Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package box. Note • After unpacking the package, make sure to check the contents of the package.
Page 3
Manuals Quick Setup Guide (Not available in all loca- Cables Power Cord Others Remote Control Batteries (AAA X 2) (BP59-00138B) (Not available in all loca- Sold separately Semi Stand KIT Warranty Card User's Guide tions) D-Sub Cable MagicInfo Software CD, MagicInfo Manual CD (Applicable to the 460UTn-2, 460UTn-B...
Page 4
Sold separately RGB to BNC Cable Wall Mount KIT Your LCD Display Front SOURCE button Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [Display- Port] →...
Page 5
Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the LCD Display. Rear Note See the "Connections"...
Page 6
• Connect a DVI or DVI-HDMI cable to OUT (LOOPOUT)] on the product and [DVI IN] or [HDMI IN] on another monitor. • HDMI and network signals sent via the [DVI OUT(LOOPOUT)] port are dis- played on the second display which has [DVI IN] port.
[DP IN] on the product Connect a DP cable to and DP IN on another display. AV/COMPONENT AUDIO IN [L-AUDIO- [AV/COMPONENT AUDIO IN Connect the [L-AUDIO-R]] port on the monitor to the audio output port on the PC or on the external de- vice using an audio cable.
Page 8
Note The MAGICINFO OUT port must be connec- [HDMI IN 2 (MAGICINFO)] port. ted to the RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port [RJ45 MDC] on the Connect the LAN cable to product and LAN on the PC. To use an MDC, the MDC program must be installed on the Note Go to Multi Control and select RJ45 MDC as...
Page 9
Note See the "Connections" section for details about cable connections. USB (USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. Note Applicable to the 460UTn-2, 460UTn-B mod- el only. Kensington Lock slot A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations.
Page 10
Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequen- POWER Number Buttons / GUIDE button + VOL - POWER Number Buttons...
Page 11
SOURCE D.MENU TOOLS Up-Down Left-Right but- tons INFO PC/DVI/HDMI/DP TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE Selects a connected external input source or MagicInfo mode. Press the button to change the input signal SOURCE. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time.
Page 12
comes back on if MUTE or - VOL + is pressed in the Mute mode. In TV mode, selects TV channels. CH/P - This is activated when a TV tuner box is installed. Selects the TV mode directly. - This is activated when a TV tuner box is installed. Opens the on-screen menu and exits from the menu or MENU closes the adjustment menu.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card.
Connect the power cord for your LCD Display to the POWER port on the back of the LCD Display. Turn on the power switch. Note Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Note •...
Connect between the the input port on another monitor using a DVI cable. Connect between the input port on another monitor using a stereo cable. Note Select DVI Mode as an input source for the external monitor connected to DVI OUT does not support HDCP. Connecting AV Devices Connect an audio cable to the product and the audio port on an external device such as a VCR or...
Connecting to a Camcorder Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the play . Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the LCD Display .
Connecting Using a HDMI Cable Connect an HDMI cable to 460UT-2, 460UT-B model) or output port on a digital device. SOURCE on the product or remote control and select "HDMI1 / Press HDMI2(only with a 460UT-2, 460UT-B model)" Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to 460UT-2, 460UT-B model) or...
nect the opposite jack to the the LCD Display. SOURCE on the product or remote control and select "HDMI1 / Press HDMI2(only with a 460UT-2, 460UT-B model)" Connecting a DVD Player Connect a RGB to Component cable between the IN] port on the LCD Display and the P Connect a set of audio cables between the [L-AUDIO-R]] on the LCD Display and the AUDIO OUT jacks on the DVD player.
Connecting a DTV Set Top (Cable/Satellite) Box Connect a RGB to Component cable between the IN] port on the LCD Display and the P Connect a set of audio cables between the [L-AUDIO-R]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Connecting a LAN Cable Connect the LAN cable between the [LAN] port on your PC. Note Applicable to the 460UTn-2, 460UTn-B model only. Connecting a USB devices You can connect USB devices such as a mouse or keyboard. Note Applicable to the 460UTn-2, 460UTn-B model only. [LAN] port on the product and the...
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, etc.
Check if the signal cable between the computer and the LCD Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.
The screen color is inconsistent. Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
Page 25
Check if the batteries are empty. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q & A How can I change the frequency? The frequency can be changed by reconfiguring the video card.
Page 26
Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the In- formation section or contact your dealer.