Philips Norelco HC7452 Manual

Features
ENGLISH
IMPORTANT
SAFETY
A
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
B
the following:
Read all instructions before using this
appliance.
DANGER
C
To reduce the risk of electric shock:
D
1. Do not reach for a clipper that has fallen into
water. Unplug immediately. E
2. Use clipper only in dry condition. Do not use
while bathing or in a shower.
3. Do not submerge clipper in water.
F
4. Do not place or store clipper where it can
fall or be pulled into a tub or sink. Do not
G
place in or drop into water or other liquid.
5. Always unplug this clipper from the electrical
outlet immediately after using, except when
clipper is (re)charging.
6. Unplug clipper before cleaning.
A Hair Clipping Comb
7. When discarding clipper, unplug clipper to
B Cutting Unit
remove rechargeable battery. See Battery
C Adjustable Wheel Hair Length
Removal instructions.
Setting Selector
8. The batteries used in this device may present
D On/Off Button
a fire or chemical burn hazard if mistreated.
E Turbo Button
Do not disassemble, heat above 100°F
F Charging Light
(212°F) or incinerate.
G Socket for Appliance Plug
WARNING
H Cleaning Brush
I Adaptor
To reduce the risk of burns, fire, electric
J Appliance Plug
shock or injury to persons:
K Storage Case
Full Two-Year Warranty
1. Close supervision is necessary when
45-Day Money-Back Guarantee
this appliance is used by, on, or near children
or invalids.
2. Use this clipper for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this clipper if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or
dropped into water. For assistance visit our
website www.philips.com/norelco or call
1-800-243-3050.
4. Do not rinse or immerse the clipper handle
in water or any other liquid.
5. Keep the clipper, cord and any attachments
away from heated surfaces.
6. Never drop or insert any object into any
opening.
15 mm
14 mm
7. Do not use the adapter in or near a power
13 mm
outlet that contains an electric air freshener 12 mm
11 mm
to prevent damage to the adapter.
8. Do not operate, charge or plug in clipper
outdoors or where aerosol (spray) products
are being used or where oxygen is being
administered.
9. Always check cutters, cutting unit and comb
before using the clipper. Do not use the
clipper if cutters, cutting unit or comb are
damaged, as injury may occur.
10. Always attach plug to clipper first, then to
outlet. To disconnect, switch Clipper OFF,
then remove plug from outlet.
11. To prevent possible damage to the cord, do
not wrap cord around the clipper.
12. Use only the cord provided to charge and
(re)charge clipper.
13. Never put clipper in direct sunlight or store
at a temperature above 140°F.
14. This clipper is for use on human hair only.
Do not use this clipper for any other
purpose.
15. Only use the power plug and other
accessories supplied with the clipper.
SAVE THESE
INSTRUCTIONS
2
IMPORTANT: The power plug contains
a transformer. Do not cut off the power 1
plug to replace it with another plug as this
will cause a hazardous condition.
Put It To The Test
Like many new products, your Philips Norelco
Registration
Hair Clipper may take a little getting used to. If
you are using an electric Clipper for the first time,
Congratulations on your purchase and welcome
or if you've been using a different brand, take
to Philips Norelco!
the time to acquaint yourself with your new Hair
Clipper.
To fully benefit from the support that Philips
Norelco offers, register your product at
Your Hair Clipper features a double-sharpened
www.norelco.com/register
cutting element with reduced friction as well as
Turbo power to boost cutting speed for a perfect
cut even on the thickest hair.
Throw your scissors away and put your new
Hair Clipper to the test. We guarantee precise
results or Philips Norelco will refund you the full
purchase price as long as the request is received
within 45 days of purchase.
15_HC7452.indd 1
To Charge/Recharge
Fully charge Clipper before using for the first
w
time or after non-use for a long period of time.
Charging, recharging or using Clipper at
w
temperatures below 40˚F or higher than 95˚F
H
adversely affects lifespan of the battery.
1 Be certain Clipper is OFF.
2 Insert the appliance plug directly into the
I
Clipper (fig. 1) and plug the adapter into any
120V AC outlet. Use only the cord provided.
J
3 The Charging Light on the appliance will
blink green to indicate the Clipper is charging
(fig. 2).
It will take approximately 1 hour to fully
w
charge the Clipper for a cordless clipping
time of up to 120 minutes.
K 4 When the battery is fully charged, the
charging light lights up green continuously
for 30 minutes and then turns off (fig. 3).
5 Disconnect the cord and unplug from
electrical outlet.
Turbo Power
Simply press the Turbo Button for a turbo
w
power boost for fast results, even on the
thickest hair. The memory function will
remember the last used setting.
Corded Hair Clipping
Clipper does not recharge during corded
w
clipping.
1 Connect cord provided to Clipper (fig. 1) and
plug Clipper into electrical outlet.
1 2 3 2 If battery is completely empty, wait a few
minutes before switching clipper ON.
3 Turn Clipper ON to begin clipping (fig. 4).
4 When finished clipping, switch Clipper OFF
and unplug.
4 5 6
Cordless Hair Clipping
1 Charge according to directions. Unplug
Clipper from outlet and remove cord.
7 8 9
2 Turn Clipper ON to begin clipping (fig. 4).
3 If the charge runs low while clipping, the
charging light will blink orange (fig. 2).
4 If the charge runs out while clipping, simply
connect cord provided to Clipper and outlet
10 11 12
to continue clipping.
2
Hair Clipping
1
Use this Clipper for its intended household
w
use as described in this manual.
13 14 15 Make sure that the appliance is fully charged
1 w
before you start clipping hair.
2
Before you start clipping, make sure that the
w
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
16 17 18
Only use the appliance on clean, dry hair.
2
w
Do not use on freshly washed hair.
w
Before you begin, comb the hair in the direction
w
of growth (fig. 5).
1
To achieve optimal clipping results, always move
w
the appliance slowly through the hair against
19 20 21
the direction of hair growth.
Clipping with hair clipping comb
1 Be certain the Clipper is in the OFF position.
2 Slide the hair clipping comb into the guiding
grooves on both sides of Clipper and push
until you hear it 'click' into place (fig. 6).
Make sure the comb locks properly into position.
3 Turn the Adjustable Wheel Hair Length
Setting Selector to the desired setting (fig. 7).
The Clipper can cut hair up to 24 different
lengths. See table below.
4 The remaining hair length is indicated in
millimeters on the adjustable wheel.
When you are clipping for the first time,
start at the maximum clipping length setting
(23mm/7/8 in.) to familiarize yourself with the
appliance and prevent accidentally trimming
hairs too short. As you become familiar with the
settings, adjust the Hair Length Selector to desired
trimming length.
Trimming Length Settings Table
Never rinse or immerse the Clipper in water
w
or any other liquid.
Do not apply pressure to cutters.
w
Barber
MM Inches Do not touch cutters with hard objects as this
w
Setting
may damage them.
1 #½ 3/64"
During Use:
2 ● 5/64"
If cut hairs have accumulated in the comb
w
3 #1 1/8"
area, remove hairs by shaking, blowing or using
cleaning brush provided.
4 ● 5/32"
5 #1½ 3/16" After Each Use:
6 ● 1/4"
1 Make sure the Clipper is switched OFF
and disconnected from the electrical outlet.
7 #2 9/32"
2 Remove the hair clipping comb by pressing
8 ● 5/16"
and sliding the comb off the Clipper (fig. 9).
9 #3 3/8"
3 Clean the comb with the brush supplied or
10 ● 13/32"
rinse under warm water (fig. 11).
11 ● 7/16"
4 Press the release button (1) and remove the
12 ● 15/32"
cutting unit (2) (fig. 12).
13 #4 1/2"
5 Clean the cutting unit with the brush
14 ● 9/16"
supplied or rinse under warm water (fig. 13).
15 #5 5/8"
6 Clean the inside of the Clipper with the
brush supplied (fig. 14).
16 ● 21/32"
17 ● 11/16"
7 Shake off any excess water and allow to
air dry.
18 ● 23/32"
8 Reattach cutting unit by inserting the notch
19 #6 3/4"
of the cutting unit into the guiding slot.
20 ● 25/32"
9 Push the cutting unit back onto the Clipper.
21 ● 13/16"
22 ● 55/64" 10 Clean the handle and the adapter with a
soft, dry cloth.
23 #7 7/8"
NOTE: The Clipper does not need any lubrication.
Replacing the Cutting Unit
5 Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
If your cutters become damaged or worn, do
an even result (fig. 8).
not continue using the Clipper. Replace cutters
immediately.
6 Since all hairs do not grow in the same
direction, move the appliance slowly over the
1 Press the release button (1) and remove the
crown from different directions (i.e. upwards,
cutting unit (2) (fig. 12).
downwards and across) to achieve an even
result.
2 Place the notch of the new cutting unit in
the guiding slot (1) and push the cutting unit
7 Always move the appliance against the
onto the Clipper (2) (fig. 15). You will hear
direction of hair growth.
a ‛click'.
8 Make overlapping passes over the head to
This Clipper has no other user-serviceable parts.
ensure that all hair that should be cut has
For assistance call 1-800-243-3050.
been cut.
Assistance
9 For best results with curly, sparse or long
hair, use a styling comb to guide the hair
For assistance, call toll free:
towards the Clipper.
1-800-243-3050
10 Switch the Clipper off regularly during
or visit our website:
clipping and remove the hair clipping comb
www.philips.com/support
to blow and/or shake out hair that has
accumulated.
Online information is available 24 hours a day,
7 days a week.
TIP: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
Storage
sessions.
Be sure Clipper is switched OFF. Remove cord
w
Clipping without hair clipping comb
from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
Use the Clipper without a comb to clip hair
w
banged, or subject to damage.
very close to the skin (0.5mm/1/32 inch) or to
Do not wrap cord around Clipper when
w
contour the neckline and area around the ears.
storing.
Store cord in a safe location where it will not
w
1 Remove the hair clipping comb by pressing
be cut or damaged.
and sliding the comb off the Clipper (fig. 9).
Do not place or store Clipper where
w
Be careful when you are clipping without comb
it can fall or be pulled into a tub or sink, water
attachment as when the Clipper is turned on it
or other liquid while plugged in.
will remove every hair it touches.
2 To contour the hairline around the ears, Disposal
comb the hair ends over the ears.
This Philips Norelco Clipper contains a
w
rechargeable lithium-ion battery which must be
3 Tilt the Clipper in such a way that only
disposed of properly (fig. 16).
one edge of the cutter blades touches the
Contact your local town or city officials
w
hair ends when you shape the contours
for battery disposal information or call
around the ears.
1-800-8-BATTERY or www.rbrc.com for
Only cut the hair ends. The hairline should be
battery drop-off locations.
close to the ear.
For assistance, visit our website,
w
www.philips.com/support or call
4 To contour the nape of the neck or
toll free: 1-800-243-3050.
sideburns, turn the Clipper and make
downward strokes (fig. 10).
5 Move the Clipper slowly and smoothly
following the natural hairline.
Cleaning
Clean the attachments after each use.
w
Always switch Clipper OFF, unplug and remove
w
power supply cord from Clipper before
cleaning.
Do not use compressed air, abrasive cleaning
w
agents, scourers or aggressive liquids such as
alcohol, benzene, bleach or acetone to clean
the Clipper and attachments.
Never clean, replace or remove Clipper
w
attachments with motor ON.
S E R I E S 7 0 0 0
HAIRCLIPPER 7100
HC7452
Rechargeable
Cordless/Cord
Always here to help you
Question? Question?
Contact
Contact
Register your product and get support at
Philips Philips
Norelco Norelco
www.norelco.com/register
4222 002 8400 4
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new Philips
Norelco product, Model HC7452 (except cutters and comb) against
defects in materials or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective product
without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you.
*Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O. Box 10313, Stamford, CT 06904
This symbol on the product's nameplate means it is
listed by Underwriters' Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips N.V.
© 2015 Philips Electronics North America Corporation. All Rights Reserved.
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Clipper, send the product back and we'll refund you the
full purchase price. The Clipper must be shipped
prepaid by insured mail, insurance prepaid, have
the original sales receipt, indicating purchase
price and date of purchase, and the money-back
guarantee return authorization form enclosed.
We cannot be responsible for lost mail.
The Clipper must be postmarked no later than
45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6–8 weeks AFTER
receipt of returned product.
8/27/15 11:10 AM