Product Information; Scope Of Delivery; Accessories; Warranty Conditions - Bosch EasyControl CT200 Installation And Operating Instructions Manual

3

Product information

3.1

Scope of delivery

4
Fig. 1 Scope of delivery
[1] EasyControl CT 200
[2] Quick Install Guide
[3] Screw with rawl plug 2 ×
[4] Wall plate
3.2

Accessories

The following accessories are available:
• Electronic thermostatically controlled radiator valve
• EasyControl adaptor
• EasyControl app (free of charge)
3.3

Warranty conditions

A manufacturer's warranty of 2 years is provided for the EasyControl.
3.4

Declaration of Conformity (Europe)

This product complies with RED 2014/53/EU, the European Directives
and the supplementary national requirements. Its conformity is
demonstrated by the CE designation.
The Declaration of Conformity can be downloaded on the internet
(www.bosch-easycontrol.com/manual) or can be requested from the
manufacturer. You will find the relevant web address on the back cover of
this document.
3.5

FCC Statement (USA)

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
EasyControl – 6720884199 (2018/01)
1
2
2x
3
0010018147-001
• To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment. (Example - use
only shielded interface cables when connecting to computer or
peripheral devices).
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
3.6

IC Statement (Canada)

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
3.7

Data privacy

Information about data protection can be found on the EasyControl site
1)
under Data protection.
3.8

Data connection

▶ The EasyControl supports open Wi-Fi connections and Wi-Fi
connections encrypted with WEP 128, WPA and WPA2 protocols.
WPA2 is the safest protocol and is therefore preferred.
▶ "Hidden" networks are not supported.
▶ The EasyControl takes over the time setting of the Bosch server. If
there is no connection to the server, the EasyControl can only be put
into operation in manual operation.
▶ All costs for creating an Internet connection and a smart device are to
be borne by the user.
▶ The type of connected heat source determines, which functions can
be used. Consult the EasyControl site to gain an overview of which
functions are available for which heat source.
1) See the back of this document for the web address.
Product information
1)
3