Samsung 700TSN-2 Quick Start Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. SyncMaster 700TSn-2
  6. Quick start manual
Samsung 700TSN-2 Quick Start Manual

Samsung 700TSN-2 Quick Start Manual

70" 700tsn-2 touchscreen lcd display
Hide thumbs Also See for 700TSN-2:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
LCD DISPLAY

quick start guide

700TSn-2,820TSn-2


Advertisement

Table of Contents
loading

Related Manuals for Samsung 700TSN-2

Summary of Contents for Samsung 700TSN-2

  • Page 1: Quick Start Guide

    LCD DISPLAY quick start guide 700TSn-2,820TSn-2...

  • Page 2: Package Contents

    Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking Manuals Quick Setup Guide...

  • Page 3: Checking The Contents Of The Package

    Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package...
  • Page 4 Manuals Quick Setup Guide (Not available in all loca- MagicInfo Software CD, MagicInfo Manual CD Cables Power Cord Others Remote Control Batteries (AAA X 2) (BP59-00138A) (Not available in all loca- Sold separately RGB to BNC Cable Wall Mount KIT LCD Display Warranty Card User's Guide...
  • Page 5 Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values.
  • Page 6 Use this button for turning the LCD Display on and off. Brightness Sensor (Optional) Automatically detects the surrounding brightness it accordingly. Note This function is activated only on the models equipped with an auto bright- ness sensor. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions.
  • Page 7 RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB/COMPONENT IN (PC Connection Terminal (Input)) • Use a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) • Connect the RGB/COMPONENT IN port on the monitor to the COMPONENT port on the external device using the D-SUB to COMPONENT cable.
  • Page 8 Note Up to 6 Full HD or 10 HD monitors can be connected (May differ depending on the product). AV IN [VIDEO] Connect the [ VIDEO ] terminal of your mon- itor to the video output terminal of the exter- nal device using a VIDEO cable.

  • Page 9: Remote Control

    Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequen- RGB OUT LAN (LAN Connection Terminal) USB1,USB2 (USB Connection Terminal)
  • Page 10 POWER 3. Number Buttons 4. DEL / GUIDE but- 5. + VOL - SOURCE D.MENU 8. TOOLS 9. Up-Down Left-Right but- tons INFO 11. COLOR BUTTONS TTX/MIX 13. MTS/DUAL Turns the product On. Turns the product Off. Press to change the channel. The "-"...
  • Page 11 ENTER/PRE-CH MUTE CH/P 17. TV MENU RETURN EXIT 21. MagicInfo Mechanical Layout (700TSn-2) Mechanical Layout broadcasting type by using the DUAL button on the remote control while watching TV. This button is used to return to the immediately previous channel. - This function does not work for this LCD Display.

  • Page 12: Lcd Display Head

    • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions...

  • Page 13: Wall Bracket Installation

    • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

  • Page 14: To Mount The Product On The Wall Bracket

    There are two hinges(left and right). Use the correct one. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
  • Page 15 Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. •...

  • Page 16: Wall Bracket Angle Adjustment

    Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
  • Page 17 When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation profes- sionals will visit you and install the bracket.
  • Page 18 • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
  • Page 19 Wall Bracket(1) Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.
  • Page 20 Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
  • Page 21 Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes.
  • Page 22 Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.

  • Page 23: Connecting A Computer

    Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, RGB/COMPONENT IN port on the back of your LCD Display and the 15 pin D-sub Port on the computer.

  • Page 24: Connecting To Other Devices

    • Turn on both your computer and the LCD Display. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices • AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display.

  • Page 25: Connecting Av Devices

    • The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. Connecting AV Devices Connect the Video and [R-AUDIO-L] port of the DVD, VCR or DTV Set-Top Box to the Video and [R-AUDIO-L] LCD Display. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted.

  • Page 26: Connecting Using A Dvi Cable

    Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Connecting Using a DVI Cable Connect between the DVI OUT port on the LCD Display and the input port on another monitor using a DVI cable.

  • Page 27: Connecting Using A Dvi To Hdmi Cable

    Select HDMI using the SOURCE button on the front of the LCD Display or on the remote control. Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable.

  • Page 28: Connecting A Lan Cable

    Connecting the Touch Screen USB hub Note To use the touch screen function in MagicInfo mode, flip the toggle switch to the left. To use the touch screen function in PC mode, connect the USB port on your PC to the product using the USB cable and then flip the toggle switch to the right.
  • Page 29 Connections You can connect USB devices such as a mouse or keyboard.

  • Page 30: Troubleshooting

    Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.

  • Page 31: Symptoms And Recommended Actions

    2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, etc.

  • Page 32: Problems Related To The Screen

    Check if the signal cable between the computer and the LCD Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.

  • Page 33: Problems Related To Audio

    The screen color is inconsistent. Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
  • Page 34 Check if the batteries are empty. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q & A How can I change the frequency? The frequency can be changed by reconfiguring the video card.
  • Page 35 Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the In- formation section or contact your dealer.

This manual is also suitable for:

820tsn-2

Table of Contents