AT&T CL82107 Quick Start Manual

CL82107/CL82207/CL82307/
This quick start guide provides you
CL82357/CL82407/CL82507
with basic instructions only. For
more complete instructions, refer
to your Abridged user's manual
provided in the package, or see the
online Complete user's manual at
www.telephones.att.com/manuals.
Quick start guide
Part lists
Ì
1 for CL82207
Ì
2 for CL82307/
CL82357
Ì
3 for CL82407
Ì
4 for CL82507
Install
Telephone base
Notes:
Ì
Plug one end of the telephone line cord into a telephone jack or a DSL
filter.
Ì
If you have DSL high-speed Internet service, a DSL filter (not included)
is required.
Charger
Caution: Use only the power adapter(s) provided with this product.
To obtain a replacement, visit our website at
www.telephones.att.com 1 (800) 222-3111
or call
1 (866) 288-4268
Canada, dial
.
Battery
Install the battery, as shown below. Charge your handset(s)
before initial use. The battery is fully charged after ten hours
of continuous charging.
THIS SIDE UP /
CE CÔTÉ VERS LE HAUT
Ì
1 for CL82107
Ì
2 for CL82207
Ì
3 for CL82307/
CL82357
Ì
4 for CL82407
Ì
5 for CL82507
CL82107/CL82207/CL82307/
CL82357/CL82407/CL82507
Quick start guide
Caution: Use only the supplied rechargeable battery or replacement
battery (model BT183342/BT283342).
Overview
Handset
Ì
CHARGE light On when the handset is charging in
the telephone base or charger.
Ì
PUSH TO TALK Press to initiate a one-to-one or
one-to-group broadcast.
Ì
Press and hold to broadcast to a
group of system devices.
Ì
Press repeatedly to view the last
REDIAL
PAUSE
ten numbers dialed.
Ì
While entering numbers, press and
hold to insert a dialing pause.
. In
Ì
MENU When the handset is not in use,
SELECT
press to show the menu.
Ì
While in the menu, press to select
an item or save an entry or setting.
Ì
FLASH Press to make or answer a call.
Ì
During a call, press to answer an
PHONE
incoming call when you receive a
call waiting alert.
Ì
During a call, press to hang up.
CANCEL
Ì
While in a menu, press to cancel an
OFF
operation, back up to the previous
menu, or exit the menu display; or
press and hold this button to exit to
idle mode.
Ì
DIR Press DIR to show directory entries
when the handset is not in use.
Ì
Press to scroll up or down while in
menus.
Ì
Press to increase or decrease the
listening volume when on a call.
Ì
CID Press CID to show caller ID log
when the handset is not in use.
Ì
1 Press and hold to set or dial your
voicemail number.
Ì
Press to switch to tone dialing
temporarily during a call if you have
pulse service.
Ì
While entering names, press to
change the next letter to upper or
lower case.
Ì
Press and hold to enter the
QUIET mode setting screen, or to
deactivate QUIET mode.
We recommend you program your telephone system
before use. The following are a few examples of common
features to set before using the telephone. Refer to the
Handset settings and Answering system settings in
the Abridged user's manual or the online Complete user's
manual for detailed instructions on setting all telephone
features.
Date and time
Note: Set the date/time before using the answering system.
1. ->
2. Enter the month, day and year using the dialing keys ->
SELECT.
3. Enter the hour and minute using the dialing keys.
4. or
Basic answering system setup via
voice guide
Handset
You can follow the voice guide to record your own
Ì
Press to make or answer a call using
announcement, set the number of rings and set the
the speakerphone.
message alert tone.
Ì 1. ->
During a call, press to mute the
MUTE
DELETE microphone.
2. or
Ì
Press to delete digit or character.
3. Set up the answering system by inputting the designated
numbers, as instructed.
Ì
CALL BLOCK Press to block the incoming call
when the telephone is ringing.
Record your own announcement
Ì
When on a call, press to block the call.
Ì
When the handset is not in use, Your outgoing announcement plays when calls are
press to show the call block menu. answered by the answering system. You can use the preset
announcement to answer calls, or replace it with your own
recorded announcement.
Telephone base
1. ->
Ì 2.
IN USE indicator On when the telephone is in
use, or when the answering
3.
system is answering an
4. Facing the handset, record your announcement and press
incoming call.
5 to end recording.
Ì
Flashes when another telephone
is in use on the same line.
Number of rings
Ì
Shows the number of
You can set the answering system to answer an incoming
message
messages.
call after 2, 3, 4, 5, or 6 rings. You can also select toll saver. If
counter
you choose toll saver, the answering system answers a call
X / DELETE Ì
Press to delete the message after two rings when you have new messages, and after four
currently playing. rings when there are no new messages. This enables you to
check for new messages and avoid paying unnecessary long
Ì
Press twice to delete all old
distance charges if you are calling from out of your local
messages when the telephone
area.
is not in use.
If you want the built-in answering system instead of the
Ì
Press to start or stop message
/ PLAY/STOP voicemail to answer a call, you should set the answering
playback.
system to answer a call at least two rings before the
voicemail is set to answer. Contact your telephone service
Ì provider for information on your voicemail settings.
Press to repeat a message.
/ REPEAT
Ì
Press twice to play the previous 1. ->
message.
2. or
Ì 3. or
/ SKIP Press to skip a message
4. or
Ì
While in idle mode, press to SELECT.
/ -VOLUME+ /
adjust the base ringer volume.
Ì Ringer volume
During message playback, press
to adjust the listening volume.
You can set the ringer volume level to one of the six levels, or
Ì
turn the ringer off.
Press to turn the built-in
/ ANS ON/OFF
answering system on or off.
1. ->
2.
Ì
While the phone is idle, press to
FIND HS
3. or
page all handsets.
Basic initial settings
or -> Set date/time -> SELECT.
to choose AM or PM -> SELECT.
or -> Answering sys -> SELECT.
-> Voice guide -> SELECT.
or -> Answering sys -> SELECT.
to select Announcement.
to select Record annc.
or -> Answering sys -> SELECT.
-> Ans sys setup -> SELECT.
-> # of rings -> SELECT.
to choose among 2, 3, 4, 5, 6, or Toll saver ->
or -> Ringers -> SELECT.
to select Ringer volume.
to choose the desire level -> SELECT.