A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. SyncMaster 150MP...
Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from solder removal devices not classified as “anti-static” a carpeted floor can generate enough static can generate electrical charges sufficient to damage electricity to damage an ESD. ESDs. SyncMaster 150MP...
GND-Blue GND-Blue GND-Blue No Connection No Connection Not Used GND-Sync/Self Test GND-Sync/Self Test GND-Sync/Self Test DDC Data DDC Data DDC Data H/V-Sync Not Used Horizontal sync Vertical sync Not Used Not Used DDC Clock DDC Clock DDC Clock SyncMaster 150MP...
Page 6
2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart SyncMaster 150MP...
Page 7
Sync. width 0.057ms 0.106ms 0.125ms 0.064ms 0.106ms Back porch 0.626ms 0.607ms 0.478ms 0.448ms 0.513ms Sync. polarity Positive Positive Positive Positive Negative or Negative Dot Clock 36.000MHz 40.000MHz 50.000MHz 49.500MHz 75.000MHz Sync. Type Separate Separate Separate Separate Separate Scan Type SyncMaster 150MP...
Page 8
13.714ms 12.549ms Front porch 0.017ms 0.086ms 0.020ms Sync. width 0.050ms 0.086ms 0.060ms Back porch 0.466ms 1.114ms 0.784ms Sync. polarity Positive Negative Negative Dot Clock 78.750MHz 30.240MHz 57.284MHz Sync. Type Separate Separate Separate Composite Composite Sync.-on-G Sync.-on-G Scan Type SyncMaster 150MP...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the SyncMaster 150MP monitor. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly.
Page 11
3-2 Replacement Order of Lamp Assemblies 1. After confirm there is nothing on the desk Turn the LCD module over and put it on a flat desk set to the ground. 2. Push down the stopper and slide the lamp unit. SyncMaster 150MP...
Page 12
LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state and rcommended clean bench condition. 3-3 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. SyncMaster 150MP...
Page 13
3 Disassembly and Reassembly Memo SyncMaster 150MP...
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 7. To protect aganist shock hazard,use an isolation transform. SyncMaster 150MP...
Page 15
4 Alignments and Adjustments Memo SyncMaster 150MP...
Does proper DC 5 V appear at Check IC103. Pin 1 of IC103? Does proper DC 2.5 V appear at Check FT116 and IC100. Pin 2 of IC100? Does proper DC 3.3 V appear at Check IC104. Pin 1 of IC104? Check IC101. SyncMaster 150MP...
Page 17
RA301 ~ RA304? Does the clock pulse appear at Check IC501 and related circuit of IC501. Pin 37 ~ 48 of IC501? Does the clock pulse appear at Replace FT501 ~ FT510. output of FT501 ~ FT510? Replace LCD Panel. SyncMaster 150MP...
Page 18
Check Pin 16 (AGC), 12 (CVBS) of Check IC101 and replace the tuner. IC703 (TDA9810) Check Pin 15 (CVBS) of IC204 Replace IC204. (STV6400D) Check related circuit of IC504 and Check IC504 (VPC3230D) replace IC504. Check IC301 (PW264) and replace mainboard SyncMaster 150MP...
Page 19
Does the high signal at R822? Check R856 and replace Q801. Check Pin 12 of IC800 (TDA7268) Replace IC800. Check Pin 60, 67 of Replace IC801 (MSP3450). IC801 (MSP3450) Check IC703, tuner, related circuit of IC703 and tuner SyncMaster 150MP...
Page 20
6 Exploded View and Parts List SyncMaster 150MP...