Honeywell HD55IP Quick Install Manual

Performance Series
Rugged Day/Night H.264 IP Dome Camera
Quick Install Guide
Document 800-09309V1 – Rev A – 01/12
1 Preparation
2 Camera Installation
3 Network Setup
4 Camera Operation
Introduction
Thank you for purchasing a Honeywell Performance Series Rugged Day/Night IP Dome
Camera. Before installing the camera, please read this guide carefully and verify your model:
HD55IP/HD55IPX, 720p resolution, 3.3 - 12 mm Vari-focal Auto Iris lens
HD54IP/HD54IPX, VGA resolution, 3.3 - 12 mm Vari-focal Auto Iris lens
For detailed information for your specific camera, please refer to the appropriate user guide
located on the IP Utility DVD or on the Honeywell product web site.
Before installing, Honeywell recommends that you download the latest software updates. Go
to www.honeywellsystems.com/support/download-center/index.html
instructions on the page to log on, find your camera, and then download the latest software
updates.
Product Dimensions
6.1" (154.97 mm)
Operating Notes
Power Supply This dome camera can operate on 24 V AC or PoE.
Operating Conditions to avoid:
• Viewing bright objects (for example, light fixtures) for extended periods:
• Operating or storing the unit in the following locations:
• Extremely humid, dusty, hot/cold environments (where the operating temperature is
outside the recommended range of –4°F to 122°F [–20°C to +50°C])
• Close to sources of powerful electromagnetic radiation, such as radio or TV
transmitters
• Close to fluorescent lamps or objects reflecting light
• Under unstable light sources (may cause flickering)
Document 800-09309V1 – Rev A – 01/12
1
Preparation
Removing the Dome Bubble and Turret
1. Using the supplied Allen key, loosen the captive screws on the
dome bubble. Remove the dome bubble and set it aside.
2. Gently pull the turret off the gimbal, then set it aside.
Removing the Gimbal
Remove the gimbal from the enclosure base so you can easily access the mounting holes and wiring
board (see illustration).
1. Squeeze the four black tabs until they are free of the black clips.
2. Elevate the gimbal assembly and rotate it away from the housing so that you have access to the
camera board connections and mounting holes.
Note The lanyard will keep the gimbal connected to the
housing, but should leave enough space to access the
connections and mounting holes.
Caution When moving the gimbal, make sure you do not pull
and overstress the two ribbon cables.
Mounting
holes
and follow the
Preparing the Mounting Surface
Note To prevent moisture from entering the housing, position the enclosure with the side conduit entry
pointing down.
Note The housing is intended for mounting on a flat surface only.
1. Use the mounting template to mark the mounting surface for the screw and cable access holes.
2. Pre-drill holes in the mounting surface,
as required.
Installing the Conduit Plug
The camera ships with the conduit plug
pre-installed in the enclosure base back
conduit entry. To use the back conduit
entry, remove the conduit plug and install it
in the side conduit entry after loosening the
locking screw. (See
Top View
Camera.) Retighten the locking screw to
the
secure the conduit plug in place.
Note For secure installations, protect
surface-mounted cables with
plastic or metal cable covers.
Dome bubble
Lanyard
Gimbal
Black
clips (x4)
Rubber washer
Back conduit entry
Screws
Enclosure base
Conduit
plug locking
screw
in
Adjusting
Side
conduit
entry
Conduit plug
2
Camera Installation
Mounting the Camera
1. Route the cables through your chosen conduit entry.
2. Mount the camera to a wall or ceiling using the supplied screws.
Turret
If you are using screws other than those supplied by Honeywell, then please remove the rubber
washers from the Honeywell-supplied screws, and then install them under the head of each of
your screws. See the
Installing the Conduit Plug
Connecting the Wiring
1. Connect the power input:
• For 24 V AC connection, locate the two-pin green connector that was shipped with
your camera and make the necessary connections.
• For PoE connection, connect a CAT5 cable to the RJ45 network connector.
Black
tabs
(x4)
Note It is not recommended that you supply both 24 V AC and PoE at the same time.
2. Connect to the network:
Connect a CAT5 cable to the RJ45 network connector, if you haven't already done so.
Note For detailed configuration information, refer to the Reference Guide for your camera
located on the IP Utility DVD.
Sealing the Wiring
To prevent moisture from entering the housing, if you are using the back conduit entry, apply
sealant around the conduit connection and the mounting screws.
illustration.
RJ45 Ethernet network connection
Local video out
(adjusting and focusing)
Power: 24 V AC
Please turn over