Icom IP100H Instructions page 2

PANEL DESCRIPTIONS
D Front and side panels
Antenna connector
Attach the supplied antenna.
Or, attach the supplied antenna connector
cap, if the internal antenna is used.
CAUTION: NEVER HOLD just the
attached antenna when carrying the
communication terminal.
[PTT] switch
In the simplex mode, hold down to
transmit, and release to receive.
In the full-duplex mode, push to make a call.
[Option] key
• Push to hang up a telephone call.
Or, push to select one of the often
used messages or IDs, depending on
the settings.
• Hold down until "Emergency" is dis-
played to send an emergency call de-
pending on the settings.
Internal microphone
When the VOX function is used, the
internal microphone is disabled.
D Function keys
[ ] (Address) key
Repeatedly push to select an address
book from All, Group, Talkgroup,
Individual or Telephone.
• Selectable address book may differ,
depending on the IP1000C settings.
• Push [J]/[K] to select a desired address.
[ ] (Call History) key
Repeatedly push to select call history
from the TX log, RX log, TX MSG log,
RX MSG log, TX TEL log or RX TEL log.
• Selectable log may differ, depending on the
IP1000C settings.
• Push [J]/[K] to select a desired log.
• Hold down until "Emergency" is displayed
to send an emergency call, depending on
the settings.
[J] (Up)/[K] (Down) keys
Push to select a desired address (ID),
log, message, status or the Area Call
function.
D Function display
Blinks Scrolls
1/23 12:34 1/23 12:34
All Back to office ASA
Standby screen When a message is received
• Signal strength indicator
Displays the signal strength in 3 levels when your
communication terminal is in a service area.
" " blinks when you are out of the service area, and " " is
displayed if your communication terminal is not registered,
or not connected to the IP1000C.
[PWR/VOL] knob
Turns the communication terminal
power ON or OFF and adjusts the audio
output level.
Function display
[ / ] jack
(External microphone/speaker jack)
Connect an optional speaker-microphone
or headset for hands-free, full-duplex
operation.
CAUTION: Attach the jack cover
when optional equipment is not used.
Be sure to turn power OFF before
connecting or disconnecting optional
equipment to or from the [ / ] jack.
Function keys
Internal speaker
When an optional speaker-microphone
or headset is connected, the internal
speaker is disabled.
[FUNC] key
• Push to select a Talkgroup, depending
on the settings.
• After a desired address is selected, re-
peatedly push to select a message, sta-
tus, or the Area Call function select sta-
tus.
• Selectable functions may differ, depending
on the IP1000C settings.
• Push [J]/[K] to select a desired message,
status or the function setting.
[CLR• ] (Clear•Lock) key
• Push momentarily to select the
standby screen.
• Hold down for 1 second to turn the Key
lock function ON or OFF.
•
Call mode icon
: Displayed when All or Group call is selected.
: Displayed when Individual call is selected.
: Displayed when Telephone call is selected.
: Displayed when Talkgroup call is selected.
• Area Call function icon
Displayed when the Area Call function is ON.
• Pocket beep function icon
Displayed when the Pocket beep function is ON.
• P-Bell function icon
Displayed when the P-Bell function is ON.
• Key lock function icon
Displayed when the Key lock function is ON.
• Battery indicator
Displays the attached battery pack's remaining battery charges.
BATTERY CHARGING
D Using the BC-202
The BC-202 rapidly charges a battery pack.
Charging time: Approximately 2 hours for the BP-271
Approximately 3.5 hours for the BP-272
The following item is required.
• A power adapter ( A different type, or no power adapter is supplied,
depending on the charger versions).
Turn OFF the power
Communication Battery pack
terminal
+ battery pack
AC outlet
Tapping screws
Power adapter
3.5×30 mm
Charging
indicator
Desktop charger
BC-202
CALLING PROCEDURES
1. Push [ ] several times to select a desired address
book.
・ Select "All" for all stations call, "Group" for group call,
"Talkgroup" for talkgroup call, "Individual" for individual
station call or "Telephone" for telephone call.
・ Selectable address book may differ, according to the
IP1000C's setting.
2. Push [J]/[K] several times to select a desired ID or
extension number.
・ Selectable ID or extension number may differ, according to
the IP1000C's setting.
・ You can select a desired ID or extension number from call
history by pushing [ ] for easy recalling.
3. If you want to send a message or status, or make an
Area Call, push [FUNC] several times.
・ Selectable function may differ, according to the IP1000C's
setting.
・ Select "Message" to transmit a message, "Status" to
transmit a status, or "Area Call" for an Area Call.
・ When Area Call is selected, push [J]/[K] to select ON.
4. Push [PTT] to make a call.
5. Hold down [PTT], and speak at your normal voice
level.
6. Release [PTT] to listen.
7. Repeat the steps 5 and 6 until you finish your
conversation.
8. To hang up the telephone call, push [Option].
For your information
When the VOX function or full-duplex mode is set in the
IP1000C, the steps 5 and 6 are not necessary.
When the VOX function is set, speak into the headset
microphone to transmit, then stop speaking to listen.
In full-duplex, you can speak and hear the other person at
the same times.
NOTE: Use the optional HM-153LS, HM-166LS, or HS-85
with OPC-2144 for full-duplex operation.
*This document is described based on the IP100H firmware version 2.04.
D Using the BC-211
The BC-211 rapidly charges up to 6 battery packs.
Charging time: Approximately 2 hours for the BP-271
Approximately 3.5 hours for the BP-272
The following item is required.
• A power adapter (not supplied with some versions).
Turn OFF the power
Battery pack
Communication
terminal
+ battery pack
Multi-Charger AC outlet
BC-211
Charging indicator
(one for each slot)
Power adapter
(BC-157S)
OPTIONS
・ BP-271/BP-272
Li-ion battery packs
BP-271: 7.4 V/1150 mAh (minimum), 1200 mAh (typical)
BP-272: 7.4 V/1880 mAh (minimum), 2000 mAh (typical)
・ BP-273
(for LR6 (AA) × 3 alkaline batteries)
battery case
・ BC-202
+ BC-123S
desktop charger ac adapter
・ BC-211
- + BC-157S
multi charger ac adapter
・ MB-127
belt clip
・ LC-181
carrying case
For full-duplex operation
・ HM-153
+ OPC-2144
earphone microphone adapter cable
・ HM-166
+ OPC-2144
earphone microphone adapter cable
・ HM-153LS/HM-166LS
earphone microphones
・ HM-183LS
-
speaker microphone
・ HM-186
- + OPC-2144
speaker microphone adapter cable
・ HS-85
+ OPC-2144
vox unit adapter cable
・ HS-102
+ OPC-2359
headset ptt switch cable
For simplex operation only
・ HM-186LS
-
speaker microphone
・ HS-94/HS-95
/HS-97
headsets throat microphone
+ OPC-2006LS /OPC-2328
adapter cable ptt switch cable
HS-94: Ear-hook type
HS-95: Neck-arm type
OPC-2006LS: For VOX operation
・ SP-13
+ OPC-2144
earphone adapter cable
Icom is not responsible for the destruction or damage to the
Icom communication terminal, if the malfunction is because of:
• Force majeure, including, but not limited to, fires, earthquakes,
storms, floods, lightning, other natural disasters, disturbances,
riots, war, or radioactive contamination.
• The use of Icom communication terminal with any equipment
that is not manufactured or approved by Icom.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand, and/or other countries.
All other products or brands are registered trademarks or trademarks of
their respective holders.