Advertisement
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
13. Do not use outdoors.
should always be taken including the following:
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
1. Read all instructions before using this appliance.
15. Always use on a dry, level surface.
2. Use fan only for purposes described in the instruction
16. Do not operate fan until fully assembled with all
manual.
parts properly in place.
3. To protect against electrical shock do not immerse
17. This product is intended for household use ONLY and
unit, plug or cord in water or spray with liquids and
not for commercial or industrial applications.
plug the appliance directly into a 120V AC electrical
18. WARNING: To reduce the risk of electrical shock
outlet.
and injury to persons, do not use in window.
4. Close supervision is necessary when any appliance is
19. WARNING: To reduce the risk of fire or electric
used by or near children.
shock, do not use this fan with any solid-state speed
5. Unplug from outlet when not in use, when moving
control device.
fan from one location to another, before putting on
20. This product employs overload protection (fuse). A
or taking off parts and before cleaning.
blown fuse indicates an overload or short-circuit
6. Avoid contact with moving parts.
situation. If the fuse blows, unplug the product from
7. Do not operate in the presence of explosive and/or
the outlet. Replace the fuse as per the user servicing
flammable fumes.
instructions (follow product marking for proper fuse
8. To avoid fire hazard, NEVER place the cord under
rating) and check the product. If the replacement fuse
rugs or any parts near an open flame, cooking or
blows, a short circuit may be present and the product
other heating appliance.
should be discarded or returned to an authorized
9. Do not operate any appliance with a damaged cord
service facility for examination and/or repair.
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
PLEASE READ AND SAVE
return to an authorized service facility for
examination and/or repair.
THESE IMPORTANT
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
SAFETY INSTRUCTIONS
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
HANF76BLZ-UC_15EM1.indd 2
F E AT U R E S - O P E R AT I O N S
ASSEMBLY INSTRUCTIONS
ADJUSTMENT INSTRUCTIONS
Your Table Fan comes completely assembled and is ready
Tilt Adjustment
for immediate use. Carefully unpack your fan, read the
Move or adjust the fan head to desired position.
instructions completely, plug it in and enjoy!
Wall Mounting Instruction
1. Use the mounting location guide below as a template
OPERATING INSTRUCTIONS
to outline the hole location.
1. Set fan on a dry, level surface.
2. Using 1/4 inch (0.6cm) drill bit, drill pilot hole
2. Plug cord into any standard 120 volt AC outlet. Please
through the wall.
o
make sure the speed control is in the OFF position (
).
3. Insert 1/4 inch (0.6cm) plastic anchors into the holes.
3. The Speed Control is located on the back of the Fan
4. Screw in two #8-15 x 1- 1/4 inch (0.6cm) screws
Motor Housing. The speed is adjusted by turning the
through the two holes in the base.
o
speed control to the desired setting: OFF - (
), HIGH
5. Hang the fan onto the screws.
- (II), LOW - (I).
6. Hardware not included with fan.
CLEANING/MAINTENANCE INSTRUCTIONS
Figure 1
A
Follow these instructions to correctly and safely care for
B
A. Fan Head
your fan. Please remember:
B. Tilt Adjustment
REPLACEABLE FUSE
Knob
If your (5 Amp, 125 Volt) replaceable fuse blows, please
C. Fan Base
visit our website at www.holmesproducts.com for
information on how to order a new fuse. Follow the below
instructions to replace the fuse on the plug.
C
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
C L E A N I N G / M A I N T E N A N C E
NOTE: Ensure that fuse
Figure 2
cover is completely open
before attempting to
Fuse cover
remove fuse.
3. Remove fuse carefully by
using a small screwdriver
to pry the fuse out of the
compartment by the metal
ends of the fuse. (see
Figure 2)
4. Place plug on a solid, flat surface. Insert new 5 Amp,
125 Volt fuse into fuse compartment and use a small
screwdriver to secure the metal ends of the fuse into
the compartment.
CAUTION: Risk of fire. Replace fuse only with 5
Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the fuse.
6. Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
FAN CLEANING
• Always unplug the fan before cleaning or
disassembling.
• Do not allow water to drip on or into the fan motor
housing.
• Use a soft cloth moistened with a soap solution to
carefully clean the front and rear grills.
MOUNTING LOCATION GUIDE
Use this diagram to help properly line up screws.
• Do not use any of the following as a cleaner:
gasoline, thinner, benzene.
Fuse
We recommend the periodic cleaning of your fan by
lightly running a vacuum cleaner nozzle over the fan grill
to remove any dust or dirt that may have accumulated
inside or on the unit.
NOTE: Please be cautious around the motor housing
Metal ends
area. Do not allow the motor or electronics to be exposed
to water. Do not attempt to take off the grills of this fan
or access the blade in any way.
FAN STORAGE INSTRUCTIONS
Your fan should be stored in the off-season in its original
box. It is important to keep it in a safe, dry location.
• We recommend using the original (or appropriately
sized) box.
• Please remember to protect the fan from dust or
moisture.
If you have any questions regarding your product or
would like to learn more about other Holmes
®
products, please visit our website at
www.holmesproducts.com. For inquiries regarding
recycling and proper disposal of this product, please
contact your local waste management facility.
1/20/15 9:55 AM
Advertisement
