Motorola H270 Quick Start Manual

BEFORE YOU BEGIN
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
Take a moment before you get started to
familiarize yourself with your new
H270 Headset.
motorola
Earhook
Volume
H270
Button
Speaker
Call Button
Microphone
Indicator Light
Quick Start Guide
Power Switch
START HERE >
Motorola, Inc.
Consumer Advocacy Office Features and
1307 East Algonquin Road
Schaumburg, IL 60196
Functions
www.motorola.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
IMPORTANT:
Guide Number: 68000202001-A
Be sure to first follow the
steps on the top row
of this guide
to complete initial setup
of your H270.
Bluetooth QD ID: Bxxxxxx
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
© 2008 Motorola, Inc. All rights reserved.
1 2
CHARGE START BLUETOOTH
FEATURE
Your Headset's Battery
Your Phone
Your phone's Bluetooth feature is off by default.
Before you can use your headset, you must pair
To use your headset, you must turn on the
(link) it with your phone.
Bluetooth feature in your phone.
Step A - ENSURE HEADSET IS IN PAIRING
For most Motorola phones (at the main menu):
MODE
1 Verify slide switch is in the off position
(toward the charging port). 1 Press ( Menu ) > Settings > Connection >
M Power on headset by sliding the Power switch
towards the microphone to initiate easy
2 Bluetooth Link > Setup.
Plug the Motorola charger into the end of the
pairing. After a few moments, the indicator
headset.
light will be steadily lit in blue to indicate
2
Scroll to Power.
The indicator light turns red or purple when
headset is in pairing mode.
the battery is charging. It may take up to 1
3 Select Change.
minute for the indicator light to turn on.
When the headset's battery is fully charged
4 Scroll to On.
(about 2 hours), the indicator light turns blue.
3 Disconnect the charger.
5
Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
Note: Headset is not functional while charging.
until you turn the feature off.
Note: This product uses a lithium ion, rechargeable,
non-replaceable battery. Under normal use, the expected life If the headset does not enter pairing mode,
Note: These steps are for most Motorola phones.
of the rechargeable battery is approximately 400 charges. see TROUBLESHOOTING for help.
For other phones, see your phone's user's guide.
TURNING HEADSET
WEARING THE
ON AND OFF
HEADSET
To turn your headset on, slide the switch
You can wear your H270 headset on your left or
toward the microphone. The indicator light To wear your headset, flex the earhook and
right ear. The headset comes ready for the right
flashes blue three times, then flashes in
loop it over your ear as shown. ear. To change the headset for the left ear:
blue and purple (if connected with a device)
or is steadily blue (if ready to be paired).
1
To turn your headset off, slide the switch
toward the charging plug. The indicator light
flashes three times then turns off.
2
3
Be sure to position the ear cushion into your
ear canal for optimal audio performance and
Indicator
comfort.
Power Switch
Light
3 4
PAIR
Your Headset and Phone
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
For most Motorola phones:
1 Menu >
On your Motorola phone, press M ( )
Settings > Connection > Bluetooth Link > 1
Handsfree > Look for Devices.
2
The phone lists Bluetooth devices it finds.
2 Select Motorola H270.
3 Select OK or Yes to pair your headset with
your phone.
Indicator Light
4
Enter the passkey: 0000
(steadily blue
5 Select OK.
for pairing)
When your headset successfully pairs and
connects with your phone, the indicator
light changes from steadily lit to flashing
blue and purple.
Power Switch
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
CHANGING FOR USE MAKING CALLS
ON OTHER EAR
Function Action
Headset Indicator
Receive a call Tap the Call button
Red
Reject a call Press and hold a
Volume button until
the ringer stops
Purple
Gently lift and pull the End a call Tap the Call button
top of the earhook up
Make a voice dial call Tap the Call button
and off speaker stem, as
and wait for voice
shown. Blue
prompt
Answer second incoming Use phone to answer
call (follow your phone's
Note: Your battery is designed to last the life of the product.
Flip the headset over. instructions)
It should only be removed by a recycling facility. ANY
ATTEMPT TO REMOVE OR REPLACE YOUR BATTERY
WILL DAMAGE THE PRODUCT.
Note: Your H270 supports both Handsfree and Headset
Attach the earhook to
Profiles. Accessing call functions depends upon which
the speaker stem, as
profile your phone supports. See your phone's user's guide
shown.
for more information.
Note: Some features are phone/network dependent.
TEST AND USE
USING YOUR H270
My headset will not enter pairing mode.
Make sure that any devices previously paired
See
with the headset are turned off. If the indicator
Your phone and headset are now paired and
Features and light is not steadily lit in blue, turn off both the
ready to make and receive calls.
Functions
other device and headset, wait 10 seconds,
on the bottom row then turn headset back on. Wait for the indicator
To make a call:
for information on
light to become steadily lit in blue, indicating
using your H270 the headset is now in pairing mode.
Place the headset over your ear.
My phone doesn't find my headset.
On the phone, dial the number you want to Make sure the indicator light on your headset is
call and press SEND key on your phone. on (lit in blue) and steady when your phone is
Note: If desired, your headset can be restored to
searching for devices (see step 3).
original factory settings. This action will erase all pairing
If your phone and headset are successfully
My headset worked before but now it's not
information stored in your headset. Thus, you will need
paired, you will hear ringing on the headset.
working.
to pair your phone and headset again (see step 3).
Make sure your phone is on and the Bluetooth
After you have successfully paired your
Note: To restore your headset to original factory feature is turned on in your phone (see step 2).
phone and headset, you don't need to
settings, press and hold both Volume and Call buttons If the Bluetooth feature was turned off or was
repeat these steps. For daily use, ensure
at the same time and slide Power switch to ON. turned on only temporarily, you may need to
that your headset is turned ON and that
restart the Bluetooth feature (see step 2) and
your phone's Bluetooth feature is ON.
pair your phone and headset again (see step 3).
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.motorola.com/Bluetoothsupport
INDICATOR LIGHT INDICATOR LIGHT
With No Charger Plugged In
With the Charger Plugged In
Audio Tone
Headset Status Headset Indicator Headset Status
Ascending tone
Charging (battery Off Power off
Two descending
level less than 70%
Three blue flashes Powering on/off
tones
charge)
Steady blue Pairing/connect mode Ring tone
Charging (battery
level more than 70% Rapid blue/purple flashes Connection successful Two short tones when
charge) pressing Volume button
Quick blue flash Incoming/outgoing call
Charging complete
High/low tones
Slow blue pulse Connected (on a call)
repeated every 60 sec.
Slow blue flash Standby (not on a call)
No audio indications;
Slow red flash Idle (not connected
deteriorating quality
to phone)
Two ascending tones
Steady red Attempting to connect
Quick red flash Low battery
Note: After 30 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
TROUBLESHOOTING
European Union Directives
Conformance Statement
Hereby, Motorola declares that
this product is in compliance with:
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product's Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product's label in
the "Search" bar on the web site.
AUDIO TONES
TROUBLESHOOTING
Headset Status
Powering on My phone does not find my headphones.
Make sure the L indicator light on your
Powering off
headphones is on and steady when your phone
is searching for devices (see step 3).
Incoming call
Volume at minimum My headphones worked with my phone
or maximum before but now their not working.
Make sure your phone is on and the Bluetooth
Low battery
feature is turned on in your phone (see step 2). If
the Bluetooth feature has been turned off or was
Out of range turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2). If you
have confirmed the Bluetooth feature is on in
Connected to phone
your phone, pair your phone and headphones
again (see step 3).
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com/bluetooth and click
Support.