Driving Your Model - Traxxas 86086-4 Owner's Manual

20 • E-REVO VXL BRUSHLESS

DRIVING YOUR MODEL

Now it's time to have some fun! This section contains instructions on
driving and making adjustments to your model. Before you go on,
here are some important precautions to keep in mind.
• Make Sure The Axle Nuts Are Tight Before Each Run
Before operating your E-Revo VXL
Brushless, take a moment to make sure
the axle nuts are tight, as they may have
loosened during shipping. The correct
size axle-nut wrench is supplied with
the truck. Check the tightness of the
axle nuts before each run. The E-Revo's
high speed and torque can loosen the
nuts over time if left unchecked.
• Allow the model to cool for a few minutes between runs. This is
particularly important when using high capacity battery packs that
allow extended periods of running. Monitoring temperatures will
extend the lives of the batteries and motors.
• Do not continue to operate the model with low batteries or you
could lose control of it. Indications of low battery power include
slow operation and sluggish servos (slow to return to center). Stop
immediately at the first sign of weak batteries. When the batteries
in the transmitter become weak, the red power light will begin to
flash. Stop immediately and install new batteries.
• Do not drive the model at night, on public streets, or in large
crowds of people.
• If the model becomes stuck against an object, do not continue to
run the motors. Remove the obstruction before continuing. Do not
push or pull objects with the model.
• Because the model is controlled by radio, it is subject to radio
interference from many sources beyond your control. Since radio
interference can cause momentary losses of control, allow a safety
margin of space in all directions around the model in order to
prevent collisions.
• Use good, common sense whenever you are driving your model.
Intentionally driving in an abusive and rough manner will only
result in poor performance and broken parts. Take care of your
model so that you can enjoy it for a long time to come.
• High performance vehicles produce small vibrations which may
loosen hardware over time. Frequently check wheel nuts and
other screws on your vehicle to ensure that all hardware remains
properly tightened.
About Run Time
A large factor affecting run time is the type and condition of your
batteries. The milliamp hour (mAh) rating of the batteries determines
how large their "fuel tank" is. A 3000mAh battery pack will theoretically
run twice as long as a 1500mAh sport pack. Because of the wide
variation in the types of batteries that are available and the methods
with which they can be charged, it's impossible to give exact run times
for the model.
Another major factor that affects run time is how the model is driven.
Run times may decrease when the model is driven repetitively from a
stop to top speed and with repetitive hard acceleration.
Tips for Increasing Run Time
• Use batteries with the highest mAh rating you can purchase.
• Use a high-quality peak-detecting charger.
• Read and follow all maintenance and care instructions provided by
the manufacturer of your batteries and charger.
• Keep the VXL-6s cool. Get plenty of airflow across the ESC.
• Lower your gear ratio. Installing smaller pinion gears will lower
your gear ratio and cause less power draw from the motor and
batteries, and reduce overall operating temperatures. Always
replace both pinion gears together.
• Vary your speed. Continuous high-speed, high-gear running
shortens the run time on the E-Revo.
• Maintain your model. Do not allow dirt or damaged parts to cause
binding in the drivetrain. Keep the motor clean.
mAh Ratings and Power Output
The mAh rating of the battery can effect your top-speed performance.
The higher capacity battery packs experience less voltage drop under
heavy load than low mAh rated packs. The higher voltage potential
allows increased speed until the battery begins to become discharged.
RUNNING IN WET CONDITIONS
Your new Traxxas model is designed with water-resistant features
to protect the electronics in the model (receiver, servos, electronic
speed control). This gives you the freedom to have fun driving your
model through puddles, wet grass, snow, and through other wet
conditions. Though highly water resistant, the model should not be
treated as though it is submersible or totally 100% waterproof. Water
resistance applies only to the installed electronic components. Running
in wet conditions requires additional care and maintenance for the
mechanical and electrical components to prevent corrosion of metal
parts and maintain their proper function.