Linear DT-3 Plus 1 Code Setting Instructions

DT-3+1
ITTER
DIGITAL
1
TRANSMITTER
ing
s
Code Setting
Instructions
800) 421-1587 • www.linearcorp.com
For more information,
Code Switches. The coding switches have eight keys numbered
pleaes visit www.devancocanada.com
itch "A", select any combination of ON or OFF positions for switch
or call toll free at 855-931-3334
(800) 421-1587 • www.linearcorp.com
Use a paper clip or other pointed object (except a pencil or pen) to
et coding switch "B", select any combination of ON or OFF Setting Code Switches. The coding switches have eight keys numbered
STEP 2
keys numbered 1-8. 1-8. To set coding switch "A", select any combination of ON or OFF positions for switch
keys numbered 3-8. Use a paper clip or other pointed object (except a pencil or pen) to
"A"
set the keys. To set coding switch "B", select any combination of ON or OFF SWITCH "B"
positions for switch keys numbered 1-8.
SWITCH "A"
Keys 1, 3,
4, and 8 OFF
Keys 1, 2, 3,
4, and 6 OFF
Keys 5, 7 Keys 2, 5, 6,
and 8 ON and 7 ON
T IS NOT ADVISABLE TO SET A CODE WITH ALL KEYS ON, OFF, OR
Keys 5, 7
NG ON AND OFF. THESE CODES CAN EASILY BE DUPLICATED. and 8 ON
e equipment. Connect the receiver(s) to the operators as
CAUTION: IT IS NOT ADVISABLE TO SET A CODE WITH ALL KEYS ON, OFF, OR
eiverʼs installation instructions. Be sure the door/gate area
ALTERNATING ON AND OFF. THESE CODES CAN EASILY BE DUPLICATED.
e transmitter and verify that the receiver triggers the operator.
ect button on the DT-3+1 activates the desired operator. Test the equipment. Connect the receiver(s) to the operators as
STEP 4
described in the receiverʼs installation instructions. Be sure the door/gate area
is clear. Activate the transmitter and verify that the receiver triggers the operator.
Check that the correct button on the DT-3+1 activates the desired operator.
ACTIVATE TRANSMITTER
TO TEST EQUIPMENT
WARNING!
E SURE DOOR
REA IS CLEAR
F OBSTRUCTIONS
WARNING!
BE SURE DOOR
AREA IS CLEAR
OF OBSTRUCTIONS
DESCRIPTION
The Delta-3 DT-3+1 is a hand-held four-channel transmitter with a
three-channel section plus an individual one-channel section. It is
designed so that channel 1 may have a system code independent
of the other three channels. This transmitter operating in
The Delta-3 DT-3+1 is a hand-held four-channel transmitter with a
c o n j u n c t i o n w i t h f o u r s i n g l e - c h a n n e l r e c e iv e r s , o r o n e three-channel section plus an individual one-channel section. It is
multi-channel receiver, can perform a variety of remote switching
designed so that channel 1 may have a system code independent
tasks. The DT-3+1 has 2 digital encoders (switch A, and switch B).
of the other three channels. This transmitter operating in
Coding switch "A" is designed for use with private multiple garage c o n j u n c t i o n w i t h f o u r s i n g l e - c h a n n e l r e c e iv e r s , o r o n e
door openers, activated by push buttons 2, 3, and 4. Coding switch
multi-channel receiver, can perform a variety of remote switching
"B" under the back cover is designed for use with less frequently tasks. The DT-3+1 has 2 digital encoders (switch A, and switch B).
1
changed codes, such as a community access gate that can be
Coding switch "A" is designed for use with private multiple garage
activated by push button 1.
door openers, activated by push buttons 2, 3, and 4. Coding switch
"B" under the back cover is designed for use with less frequently
NOTE: The transmitter transmits continuously with the button
changed codes, such as a community access gate that can be
pressed. The red indicator lights during transmission to indicate
activated by push button 1.
battery condition. Should it fail to illuminate, it is recommended that
you replace the 9-volt battery. NOTE: The transmitter transmits continuously with the button
pressed. The red indicator lights during transmission to indicate
battery condition. Should it fail to illuminate, it is recommended that
you replace the 9-volt battery.
Code Setting for Four Single-Channel Receivers. Set keys 3-8 of
STEP 3A
receivers 2, 3, and 4 to match keys 3-8 of switch "A". Set keys as follows:
Receiver 1 - Set all eight keys to match switch "B", activates from button 1
STEP 3A
Receiver 2 - Set Key 1 and 2 OFF, match keys 3-8, activates from button 2
receivers 2, 3, and 4 to match keys 3-8 of switch "A". Set keys as follows:
Receiver 3 - Set Key 1 ON, Key 2 OFF, match keys 3-8, activates from button 3
Receiver 4 - Set Key 1 OFF, Key 2 ON, match keys 3-8, activates from button 4
Receiver 1 - Set all eight keys to match switch "B", activates from button 1
Receiver 2 - Set Key 1 and 2 OFF, match keys 3-8, activates from button 2
Receiver #1 (Channel 1)
Receiver 3 - Set Key 1 ON, Key 2 OFF, match keys 3-8, activates from button 3
Match with the code set
on transmitter Switch "B"
Receiver 4 - Set Key 1 OFF, Key 2 ON, match keys 3-8, activates from button 4
1 2 3 4 5 6 7 8
SWITCH "B"
O
N
O
F
F
O
OPEN
N
Keys 1, 3,
Receiver #2 (Channel 2)
O
4, and 8 OFF
F
Match with the code set
F
on transmitterSwitch "A"
1 2 3 4 5 6 7 8
O
N
O
F
F
Keys 2, 5, 6,
O
OPEN
and 7 ON
N
O
BATTERY REPLACEMENT
F
F
The battery should last 12 to 18 months with normal use. The red
LED on the face of the transmitter will glow when the unit is
activated. When the red LED lights dimly, or not at all when
transmitting, the battery needs to be replaced. Remove the battery The battery should last 12 to 18 months with normal use. The red
access door to change the battery. Any type of 9-volt battery can LED on the face of the transmitter will glow when the unit is
be used.
activated. When the red LED lights dimly, or not at all when
transmitting, the battery needs to be replaced. Remove the battery
access door to change the battery. Any type of 9-volt battery can
be used.
ACTIVATE TRANSMITTER REPLACE BATTERY WITH
TO TEST EQUIPMENT FRESH 9-VOLT BATTERY
REPLACE BATTERY WITH
FRESH 9-VOLT BATTERY
DESCRIPTION
Code Setting for Four Single-Channel Receivers. Set keys 3-8 of
Receiver #3 (Channel 3)
Match with the code set
on transmitter Switch "A"
1 2 3 4 5 6 7 8
O
Receiver #3 (Channel 3)
Receiver #1 (Channel 1)
N
Match with the code set
O
on transmitter Switch "B"
F
F
1 2 3
1 2 3 4 5 6 7 8
OPEN O
N
Receiver #4 (Channel 4)
O
F
Match with the code set
F
on transmitter Switch "A"
OPEN
1 2 3 4 5 6 7 8
O
Receiver #2 (Channel 2) Receiver #4 (Channel 4)
N
Match with the code set
O
on transmitterSwitch "A"
F
2 F 4 5 6 8 2
1 3 7 1 3
OPEN O
N
O
F
F
OPEN
BATTERY REPLACEMENT
DT-3+1 transmitter. Code switch "A" is exposed by removing the battery access
cover by inserting your thumbnail or small screwdriver under either of the two slots
at the edge of the case. To access switch "B" remove the battery and remove the Locate coding switch. There are two digital coding switches in the
STEP 1
rear half of the case by gently pulling down and back on the battery end of the rear
DT-3+1 transmitter. Code switch "A" is exposed by removing the battery access
case. (CAUTION: the white plastic push buttons rest freely in case front and may cover by inserting your thumbnail or small screwdriver under either of the two slots
fall out if care is not exercised.)
at the edge of the case. To access switch "B" remove the battery and remove the
rear half of the case by gently pulling down and back on the battery end of the rear
case. (CAUTION: the white plastic push buttons rest freely in case front and may
fall out if care is not exercised.)
BATTERY
BATTERY
CODING
SWITCH
"A"
CODING SWITCH "A"
REAR VIEW WITH BACK COVER
REMOVED TO ACCESS SWITCH "B"
Code Setting for Four-Channel Receiver. Set coding switch keys CODING SWITCH "A"
STEP 3B
3-8 of receiver to match keys 3-8 of coding switch "A" of the DT-3+1. Matching
these keys completes the coding procedure required to activate the first THREE
channels of the receiver. The receiver keys 1 and 2 do not have to be set. Their Code Setting for Four-Channel Receiver. Set coding switch keys
STEP 3B
functions are preprogrammed to access channels 1-4. Receiver channels are 3-8 of receiver to match keys 3-8 of coding switch "A" of the DT-3+1. Matching
activated as follows: these keys completes the coding procedure required to activate the first THREE
channels of the receiver. The receiver keys 1 and 2 do not have to be set. Their
functions are preprogrammed to access channels 1-4. Receiver channels are
activated as follows:
Channel 4 of the receiver can be
ACTIVATES
CHANNEL 4 ACTIVATES
activated by setting keys 3-8 of
CHANNEL 2
Match with the code set
coding switch "B" to match keys 3-8
on transmitter Switch "A"
1
of coding switch "A". Set keys 1, and
4 5 6 7 8
ACTIVATES
CHANNEL 4
2 of coding switch "B" to on position.
Channel 4 of receiver can now be
ACTIVATES
1
activated by pressing button 1 of the
CHANNEL 3
OPEN
ACTIVATES
DT-3+1.
CHANNEL 1
Match with the code set
on transmitter Switch "A"
ACTIVATES
4 5 6 8
7
CHANNEL 1
LINEAR LIMITED WARRANTY
This product is warranted to the consumer against defects in material and workmanship for one year from the
OPEN
date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option,
replace, any device it finds that requires service under this warranty, and will return the repaired or replaced
device to the consumer at the warrantorʼs cost. For warranty service and shipping instructions contact warrantor
at the address shown below. Devices must be sent to warrantor for service at ownerʼs expense. The remedies
This product is warranted to the consumer against defects in material and workmanship for one year from the
provided by this warranty are exclusive. Implied warranties under state law are to the one year period of this
date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option,
written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above
replace, any device it finds that requires service under this warranty, and will return the repaired or replaced
limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send
copy with equipment should repair be required. This warranty gives you specific legal rights, and you may also device to the consumer at the warrantorʼs cost. For warranty service and shipping instructions contact warrantor
at the address shown below. Devices must be sent to warrantor for service at ownerʼs expense. The remedies
have other rights which vary from state to state.
provided by this warranty are exclusive. Implied warranties under state law are to the one year period of this
All products returned for warranty service require a Return Product Authorization Number (RPA#).
written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send
IMPORTANT !!!
copy with equipment should repair be required. This warranty gives you specific legal rights, and you may also
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
have other rights which vary from state to state.
signaling. However, there are some limitations which must be observed.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
devices. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
that occur on or near their operating frequencies, regardless of code settings.
signaling. However, there are some limitations which must be observed.
Changes or modifications to the device may void FCC compliance.
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
devices. As such, they have limited transmitter power and therefore limited range.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
dealer, and these facts should be communicated to the ultimate users.
that occur on or near their operating frequencies, regardless of code settings.
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device
Changes or modifications to the device may void FCC compliance.
may not cause harmful interference and (2) this device must accept any interference received, including
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
interference that may cause undesired operation.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 1999 Linear Corporation This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Copyright © 1999 Linear Corporation
CODING
SWITCH
"B"
CODING
SWITCH
"B"
CODING
SWITCH
"A"
REAR VIEW WITH BACK COVER
REMOVED TO ACCESS SWITCH "B"
Channel 4 of the receiver can be
ACTIVATES
activated by setting keys 3-8 of
CHANNEL 2
coding switch "B" to match keys 3-8
of coding switch "A". Set keys 1, and
2 of coding switch "B" to on position.
Channel 4 of receiver can now be
ACTIVATES
activated by pressing button 1 of the
CHANNEL 3
DT-3+1.
LINEAR LIMITED WARRANTY
IMPORTANT !!!
207408 D
207408 D