Page 2
Dear Customer, Thank you for choosing a Superior Innovation product. It is our intent to deliver the best products possible. Delivering innovative, well-built, ergonomic, efficient products is our goal to help you do the best job...
Page 3
Superior Innovations Reservation All of the information and data in this Operator’s Manual was up to date at the time the Operator’s Manual was sent to print. Superior Innovations research and development is continually working on product development and improvements. Therefore, we reserve the right to modify the design, appearance and features of the product without prior notice.
Page 4
Vibration Warning WARNING! Overexposure to vibration can lead to circulatory damage and or nerve damage, especially in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration. Symptoms include: numbness, loss of feeling, tingling, pricking, pain, loss of strength, and changes in skin color and condition.
Page 5
It is not possible to cover every conceivable situation. Exercise care and use common sense if you get into a situation where you feel unsafe. Stop and seek expert advice by contacting Superior Innovations, Inc., a service dealer or an experienced user. Do not attempt any task that you are unsure of.
Page 6
Before Starting Inspect equipment to ensure that there are no loose fasteners, cracks, leaks, or other obvious damage. If there are do not use until the problems are corrected. Make sure that daily maintenance has been completed. Make sure that the MagVibe™ Pro battery is fully charged. In the Box...
Warranty New equipment sold by Superior Innovations is warranted to be free from manufacturing defects under normal service for a period of one (1) year from date of purchase by the original consumer. Component manufacturers offer separate warranties and are covered separately.
Page 12
Align the QAS™ receptacle with the QAS™ dovetail and slide over to engage. Center the MagVibe Pro™ over the QAS™ dovetail and tighten both QAS™ knobs by turning them clockwise.
Page 13
Four Fastener Float Attachment (QAS™-M) Place QAS™-M adapter onto four fastener float and tighten (4) 3/8”-16 x ½” Low head socket head cap screws (supplied with adapter). You will need a 3/16” Allen tool for this operation. Loosen both QAS™ knobs by turning them counterclockwise.
Page 15
QAS™-W Slide (2) QAS™-W T-washers into the channel of the float. Place the dovetail mount onto the float and tighten (4) M6 x 10mm socket head cap screws (supplied with adapter). You will need a 4mm Allen tool for this operation.
Page 16
Loosen both QAS™ knobs by turning them counterclockwise. Make sure that the threaded studs are retracted enough to clear the dovetail. Align and slide the Magvibe™ Pro QAS™ receptacle over the dovetail on the QAS™- W adapter. Tighten both QAS™ knobs by turning them clockwise.
Page 17
Attaching the Pole Extension Press and hold the pins in pole extension, then align and insert into Magvibe™ Pro pivot handle. Push into bore and make sure that the pins snap through the two holes in the pivot handle to engage. Same procedure for an outside pole extension;...
Page 18
Button A turns the Magvibe™ Pro on and off, and Button B is an auxiliary RF control for powered accessories from Superior Innovations. To turn the Magvibe™ Pro on, simply press button A and the vibration will start. When you want to turn it off, press button A again.
Page 19
If you lose your RF remote control you can still turn the Magvibe™ Pro on and off by pressing the latching on / off switch. NOTE: This switch is very compact and was designed to be used as a failsafe if the RF remote was lost.
Page 20
Battery Indicator The battery indicator is positioned so the operator can see the status of the battery when the Magvibe™ Pro is in operation. There are 10 LED’s: 5 Green, 3 Amber and 2 Red. Every LED represents approximately 10% of battery life. For instance, if 6 LED’S are lit, you have approximately 60% of battery life remaining.
Page 21
Programming a Replacement Remote If you lost your remote and need to program a replacement, you can do it yourself. You will need to order part number D-13535. Once you receive your replacement remote, use a 4mm Allen key to remove (6) M5 socket head cap screws on the bottom plate as shown.
Page 22
Once programming is successful, apply silicon sealer between the Magvibe™ Pro main body and baseplate. Then reassemble in reverse order. Maintenance Statement The owner is responsible for the performance of all required maintenance, as described in the Operator’s Manual. Maintenance Schedule Daily Maintenance Weekly Maintenance Monthly Maintenance...
Maintenance Remove MagVibe™ Pro from the float and clean after every use. Make sure to pay special attention to the QAS™ receptacle. If concrete sets-up around the QAS™ it may become difficult to use. The MagVibe™ Pro has sensitive electronics located inside the pivot and the main body;...
Page 24
Reinstall the (4) screws and tighten using a Philips screwdriver. You may need to reprogram MagVibe Pro RF receiver if the code was lost during the battery reinstall process. See Programming a Lost Remote in this manual for instructions.
Page 25
Technical Data Motor 24V DC, 0.6A Battery 18V DC, 3000mAh Lithium Polymer Weight Gears Beveled, 3.17:1 ratio Dimensional (L x W x H) 10.425” x 6.5” x 3.16” (264.8mm x 165.1mm x 80.3mm)