Samsung DV22K6800 Series User Manual
Hide thumbs
Also See for DV22K6800 Series:
- User manual (180 pages) ,
- User manual (180 pages) ,
- User manual (60 pages)
Related Manuals for Samsung DV22K6800 Series
Summary of Contents for Samsung DV22K6800 Series
-
Page 1: User Manual
Dryer User manual DV22K6800** DV22K6800-03650A-00_EN (US)_151211.indd 1 2015-12-11 7:15:41... -
Page 2: Before Installation
Before installation Read through the following instructions before installing the dryer, and keep this manual for future reference. WARNING The control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - Do not contact these parts while the appliance is energized. - Page 3 Before installation NOTE When the exhaust duct is installed at the rear of the dryer, the rear must have at least 5.5 inch (140 mm) clearance. 5.5” (140 mm) Side by side installation 1 in. (25 mm) 25.8 in. (655 mm) 23.6 in.
- Page 4 26.6 in. (676 mm) 67 in. (1702 mm) 4.75 in. (120 mm) WARNING Samsung’s washers and dryers can be stacked to maximize usable space. You can purchase an optional stacking kit from your Samsung retailer. English 11 DV22K6800-03650A-00_EN (US)_151211.indd 11...
-
Page 5: Ducting Requirements
Before installation Ducting requirements Recommended Use only for short-run installation Weather hood type 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° Metallic Metallic Rigid Rigid elbows flexible* flexible* 80 ft. (24.2 m) 40 ft. (12.2 m) 60 ft. (28.3 m) 30 ft. -
Page 6: Exhausting Requirements
Exhausting requirements Outside the United States and Canada The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl • Refer to the local codes. space, or a concealed space of a building. WARNING Exhausting the dryer to the outside will •... -
Page 7: Electrical Requirements
Before installation Electrical requirements The wiring diagram is located on the plate • The plug must be plugged into an under the control panel or rear frame. appropriate outlet that is properly installed and grounded in accordance WARNING with all local codes and ordinances. •... - Page 8 U.S. only Canada Only Most U.S. dryers require a 120 / 240 volt, • A 120 / 240 volt, 60 Hz AC approved 60 Hz AC approved electrical service. electrical service fused through a Some require 120 / 208 volt, 60 Hz 30-ampere fuse or circuit breaker on approved electrical service.
-
Page 9: Installation
What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the accessories, contact a local Samsung service center or the retailer. Dryer at a glance 01 Top cover... - Page 10 Accessories & tools Provided accessories DRYER STACKING KIT Stacking Kit Cover Plate (Canadian models only) Required tools Pliers Cutting knife Nut driver Level Philips screwdriver Duct tape Wrench WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
- Page 11 Installation Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. STEP 1 Install the exhaust system Select a location and move the dryer to the site. For easy access, we recommend you install the dryer in the same location as your washer.
- Page 12 STEP 2 Connect the electrical wiring First, read through the “Electrical requirements” section, and then follow the instructions on this page or the next page. Instructions for a 3-wire system are on this page. Instructions for a 4-wire system are on the next page. For a 3-wire system Loosen or remove the screws from the center terminal block.
- Page 13 Installation For a 4-wire system Remove the external ground connector’s screw, and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION • To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
- Page 14 • Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block. • A strain relief must be used. • Do not loosen the nuts already installed on the terminal block. Be sure they are tight. •...
- Page 15 Installation STEP 4 Final Check When installation is complete, confirm that: • The dryer is plugged into an electrical outlet and grounded properly. • The exhaust ductwork is connected and the joints are taped. • You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct. •...
-
Page 16: Changing The Direction Of The Exhaust Duct (Optional)
Changing the direction of the exhaust duct (optional) WARNING Before performing this exhaust installation, disconnect the dryer from its electrical supply. Wear gloves to protect your hands and arms from sharp edges when working inside the cabinet. Side venting Detach the right (A) or left (B) side knockout as desired. - Page 17 Installation Reconnect the cut portion of the duct (D), and then fasten it to the ramp on the appliance base with the screw (C) which you set aside in Step 2. Connect a duct to an elbow, and then tape the duct and the elbow together with duct tape.
- Page 18 Cover the back opening with a cover plate (G). WARNING Never leave the back opening uncovered. It must be covered with a cover plate. Bottom venting Detach the bottom knockout (A). Pull the duct out of the dryer, and then remove the screw (B) from the duct.
- Page 19 Installation Reconnect the cut portion of the duct (C), and then fasten it to the ramp on the appliance base with the screw (B) which you set aside in Step 2. Insert the elbow (D) through the rear hole and connect it to the duct (C). Rotate the elbow (D) through the bottom opening.
- Page 20 Cover the back opening with a cover plate (F). WARNING Never leave the back opening uncovered. It must be covered with a cover plate. English 27 DV22K6800-03650A-00_EN (US)_151211.indd 27 2015-12-11 7:15:47...
- Page 21 Installation Switching the door position To reverse the direction of the door, we recommend that you contact a qualified technician. Unplug the power cord of the dryer. Remove the two hinge screws from the door, and then remove the door by lifting it up slightly.
- Page 22 Locate and remove the 9 screws from the door as shown. Remove the door lever. Remove the door frame. English 29 DV22K6800-03650A-00_EN (US)_151211.indd 29 2015-12-11 7:15:47...
- Page 23 Installation Rotate the door glass 180°. Reassemble the door frame and the door lever. English DV22K6800-03650A-00_EN (US)_151211.indd 30 2015-12-11 7:15:47...
- Page 24 Move the location of the screws, used to fix the door hinge, as shown. 10. Remove the lever cover by pressing the hook on it. 11. Put the lever holder on the other side as shown. English 31 DV22K6800-03650A-00_EN (US)_151211.indd 31 2015-12-11 7:15:48...
- Page 25 Installation 12. Insert and tighten the two hinge screws. 13. Insert and tighten the two screws on the opposite side of the door hinge. English DV22K6800-03650A-00_EN (US)_151211.indd 32 2015-12-11 7:15:48...