Samsung SDN- 550 Quick Reference Manual

DC/Video Lens switch
Power LED
OSD Menu
buttons
Control input for
Day/Night
Output from
Motion Detection
Factory Default Settings:
LENS =............................DC
SHUTTER =.......................- - - (Auto)
WHITE BAL=.....................ATW
BACKLIGHT =...................OFF
AGC =..............................NORMAL
SSNR=............................LOW
SENS-UP=........................OFF
<SPECIAL>
CAMERA ID =......................OFF
COLOR (Day mode)...........ON
SYNC..............................INTERNAL
Motion Detection................OFF
PRIVACY =.......................OFF
MIRROR =........................OFF
SHARPNESS =..................ON (25/31)
Info :
•
The OSD Menu will disappear after 1 minute if no
buttons are pressed.
•
A common cause of NO PICTURE is the incorrect
setting of the DC/VIDEO switch at the rear of the
camera. Check this option first.
•
In The case of unexplained faults with the camera,
select the RESET option from the SPECIAL menu.
SDN- 550 Quick Reference Guide
To Adjust the Lens Brightness Level:
1. Press the SETUP Button on the back of the
camera
Video Output
2. « LENS » is selected
3. Press SETUP 1x
Power Input
4. « BRIGHTNESS » Use
the brightness level.
5. Press SETUP 1x
6. Select « EXIT »
7. Press SETUP 1x to exit menu
To set Manual Lens and Shutter option:
1. Press SETUP at the rear of the camera.
2. « LENS » Press
3. Press 1x
4. « SHUTTER » Press
5. « MANUAL » Press SETUP 1x
6. Adjust the shutter speed (Default = 1/50. 1/120000 max.)
7. Press SETUP 1x
8. Press 7x
9. Select « EXIT » option
10. Press « SETUP » 1x to exit menu.
To enable SPOTLIGHT function (a function of BACKLIGHT):
1. Press SETUP at rear of camera
2. Press 3x « BACKLIGHT »
3. Press 4x SPOTLIGHT (Reduces areas of bright or
reflected light in the image)
4. Press SETUP 1x
5. Adjust the size and the position of the box on the screen,
using the functions 1.TOP; 2.DOWN; 3.LEFT; 4.RIGHT. For
example: select 1. DOWN using
therefore the depth of the box, using
6. To exit, select option 5 « END ». Press SETUP 1x
7. Press 5x
8. Select « EXIT » then « SETUP » to exit menu.
© Goodson Wainwright Associates Ltd. 2007 (Samsung Techwin Technical Support)
and to adjust
1x "MANUAL"
1x
1x. Adjust the values and
and .
To enable Sens-up function
1. Press SETUP
2. Press 6x « SENS-UP »
3. Press 1x « AUTO »
4. Press SETUP 1x
5. The default setting is « 8x »
6. Adjust the level using and (it is
recommended that no more than 8x is set for
general use)
7. Press SETUP 1x
8. Press 2x
9. Select « EXIT » then « SETUP » to exit menu.
To change settings for WHITE BAL:
1. Press SETUP at the rear of the camera.
2. Press 2x
3. « WHITE BAL. » Press 1x
4. « MANUAL » Press SETUP 1x
5. Adjust the RED and BLUE levels if necessary.
6. Press SETUP 1x
7. Press 6x
8. Select « EXIT » then « SETUP » To exit menu.
OR:
(AWC)
1. Press SETUP at the rear of the camera.
2. Press 2x
3. « WHITE BAL. » Press 2x
4. Now hold a white card in front of the lens so that it fills
the screen, but still reflects light.
5. « AWC » Press SETUP and hold for 3 seconds.
6. Press 6x
7. Select « EXIT » then « SETUP » to exit menu.