Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Huawei EC315
Summary of Contents for Huawei EC315
- Page 1 Quick Start Guide...
- Page 2 Thank you for choosing the 3G EVO Wingle; a Wi-Fi USB that lets you freely Mingle with multiple Wi-Fi gadgets On-the-Go! This guide briefly describes the appearance of the 3G EVO Wingle and the procedures for using the 3G EVO Wingle. For details about how to set the management parameters, please see help information on the web management page.
-
Page 3: Connection Scenarios
Connection Scenarios Scenario 1: One-device Internet access using computer... - Page 4 Scenario 2: Multi-device Internet access using Wi-Fi (connected to a computer)
- Page 5 Scenario 3: Multi-device Internet access using Wi-Fi (connected to the power adapter)
- Page 6 Getting to Know Your 3G EVO Wingle The following figure shows the 3G EVO Wingle. It is provided only for your reference. The actual product may be slightly different.
-
Page 7: Usb Connector
USB connector It connects the 3G EVO Wingle to a computer. Strap holes You can tie the 3G EVO Wingle and its cap together by threading a strap through the strap holes. - Page 8 Wi-Fi indicator It indicates the status of a Wi-Fi network. Blinking green once every 3 seconds: The 3G EVO Wingle is powered on, and the Wi-Fi function is available. Steady green: A Wi-Fi connection is set up. Off: The Wi-Fi function is turned off or fails, or the 3G ...
- Page 9 Green, blinking once every 0.2s: The software of the 3G EVO Wingle is being upgraded. Green, blinking once every 2s: The 3G EVO Wingle is registering with a 2G network. Green, solid: The 3G EVO Wingle is transmitting data ...
-
Page 10: Microsd Card Slot
UIM card slot It holds a User Identity Module (UIM) card. Also known commonly as SIM Card. Your 3G EVO Wingle is pre-configured to PTCL EVO network; and hence does not require a UIM/SIM card for service activation. microSD card slot It holds a microSD card. -
Page 11: Getting Started
Getting Started Installing the microSD Card 1. Slide the front cover off. 2. Slide the microSD card holder door towards its hinges to unlock it. Then open the door. 3. Place the microSD card into the holder. Ensure that the gold contact area faces down and that the gold contacts of the microSD card align with those of the holder. - Page 12 5. Slide the front cover back onto the 3G EVO Wingle until it snaps into place. Note: The microSD card is an optional accessory. If it is not included in the product package, purchase one separately. When installing a microSD card, ensure that the ...
-
Page 13: Using The Power Adapter
use. Otherwise, the card and your 3G EVO Wingle may be damaged and the data stored on the card may be corrupted. Using the Power Adapter Connect the 3G EVO Wingle to the power adapter's USB port, and connect the power adapter to a power outlet. - Page 14 Note: Only use power adapters compatible with the 3G EVO Wingle and provided by a designated manufacturer (HW-050100E2W). Use of an incompatible power adapter or one from an unknown manufacturer may cause the 3G EVO Wingle to malfunction, fail, or could even cause a fire.
-
Page 15: Connecting To A Network
Using Your 3G EVO Wingle The procedure for installing the management program depends on your computer's operating system. The following sections are based on Windows 7. Connecting to a Network 1. Connect the 3G EVO Wingle to one of your computer's USB ports. - Page 16 The installation wizard runs automatically. 2. Complete the installation as prompted. When the installation is complete, the 3G EVO Wingle's web management page is displayed. 3. A dial-up connection is set up and you are connected to the network in automatic mode.
- Page 17 Note: If the installation wizard does not run automatically, find the AutoRun.exe file in the driver path, and double-click the file to run it. The default user name and password of the web management page are admin. When using the 3G EVO Wingle to access a network, ...
- Page 18 By default, the 3G EVO Wingle automatically disconnects from the Internet when you are roaming outside the network coverage area. If you are not connected to the network, access http://192.168.1.1 to check the device status. If you cannot access http://192.168.1.1, disconnect ...
-
Page 19: Disconnecting From A Network
Disconnecting from a Network Remove the 3G EVO Wingle from your computer. Note: By default, the 3G EVO Wingle automatically disconnects from the network if no data is transferred within 10 minutes. If you do not need to connect to the network, it is ... -
Page 20: Setting Up A Wi-Fi Connection
Setting Up a Wi-Fi Connection 1. Ensure that the Mobile WiFi Smart's Wi-Fi function is 2. Select Start > Control Panel > Network and Internet > Network and Sharing Center > Connect to a network. Note: Before establishing a Wi-Fi connection, ensure that the computer is equipped with a wireless network adapter. - Page 21 3. Select the wireless network connection with the Mobile WiFi Smart's SSID and click Connect. Note: If a security mechanism is enabled for the wireless network connection, enter the correct network key. The SSID and the network key are printed on the ...
-
Page 22: Viewing Service Information
4. Wait until a wireless network connection icon is displayed in the lower right corner of the computer screen. A wireless network connection is set up. Viewing Service Information Visit http://192.168.1.1 to view your service information. Wi-Fi Sharing 1. Log in to the web management page http://192.168.1.1. - Page 23 3. Set up the following options according to your needs then click “Select” > “Apply”. 4. Under web share mode settings you may select the Access type as “Read only” or “Read/Write only”. Read only option is only for viewing the files from SD card – copying or downloading the file is restricted while with Read/write option you can download the file from SD card.
- Page 24 6. For uploading a file in the SD card you need to select the upload option and then browse the file from your PC which you want to upload followed by clicking the upload button. IP Sharing 1. Log in to the web management page http://192.168.1.1.
- Page 25 4. From the “Settings” page, choose “Security” > “Firewall Switch”. 5. Select the “Enable firewall” and “Open Wan IP sharing”, and then click “Apply”. 6. The “IP Sharing” link now is available. 7. By typing the Wan IP address, the other users can remotely access the web management page and view the SD files.
-
Page 26: Restoring Factory Defaults
Restoring Factory Defaults If you are uncertain of which settings you have configured or changed, you can restore the factory defaults that come with the 3G EVO Wingle, and reconfigure the device. To restore the factory defaults, connect the 3G EVO Wingle to a computer or a power outlet, and press and hold the RESET button for 5 seconds. - Page 27 Note: Restoring factory defaults deletes all the device's user-defined settings and restores all the settings on the web management page to their defaults. 31010UGQ_01...