Summary of Contents for PAC MMC200
- Page 1 Operating Manual Please Read Before Operating Unit Model MMC200 Multi-Material Cutter Service and All Spare Parts Available...
- Page 2 Compressed air………………...……..40 to 90PSI SHOULD ALWAYS BE FOLLOWED TO RE- Feed rates……………..10 selectable feed rates DUCE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOL- MMC200 Feed belt speeds LOWING: Feedrate # inches/sec cm/sec 16.8 GROUNDING INSTRUCTIONS 25.2 In the event of a malfunction or breakdown, ground- 13.2...
-
Page 3: General Instructions
Model MMC200 MULTI-MATERIAL CUTTER Do not modify the plug provided – if it will not fit the DON’T OVERREACH. Keep proper footing and outlet, have the proper outlet installed by a quali- balance at all times. fied electrician. MAINTAIN TOOLS WITH CARE. Keep tools... -
Page 4: Operation
This fea- BE KEPT FOR FUTURE REFERENCE. CON- ture can be used to stop the MMC200 by an exter- TACT ERASER IF INSTRUCTIONS ARE NOT nal signal applied to the pins of this port (a DC CLEAR. -
Page 5: Creating A New Batch
Model MMC200 Multi-Material Cutter guard during a run is not recommended. It will stop The model number and the firmware revision date the stepper motors and the piece being processed are displayed in the third line. will not be of the correct length. - Page 6 1234.56 isn’t allowed. The above. The feed rate can be changed at this point MMC200 is capable of 1% cut length accuracy only, by entering a number (0 through 9) or by pressing so, it doesn’t make sense to enter a decimal place the <+>...
- Page 7 Model MMC200 Multi-Material Cutter Model MMC200 Multi-Material Cutter prompt for a unit of measure or for the length cor- batch and to run the batch. If the operator chooses rection factor), a long beep will sound that is dis- to run some test pieces before commencing the tinctly longer than the confirmatory beep heard af- batch, press the <JOG>...
- Page 8 - CUT piece being fed (e.g. if a 28" piece is interrupted at ABORT - ESC 8", the MMC200 will continue to feed to 28" when CONTINUE - RUN the continue option is selected). This menu allows the operator to continue the...
- Page 9 Model MMC200 Multi-Material Cutter Allows the user to enter kit mode by a < > key press. To continue with the example outlined above, batch The screen will then go to the kit selecting screen: 4 will be the first batch to be run in this kit so it will be entered at index 0.
- Page 10 Model MMC200 Multi-Material Cutter INDEX #2 N KIT#1 The top line keeps a running count of kits com- SELECT BATCH: 0 pleted thus far and indicates which kit is process- LENGTH ing. A <RUN> key press gives the kit run screen:...
-
Page 11: Blade Replacement
Model MMC200 Multi-Material Cutter Some notes on kit editing: fall if not supported. Use the screws in the blade An existing kit can always be edited (i.e. add/de- as handles to safely remove the blade (see Speci- lete or change batches within a kit). Batches al- fication Photo 2). -
Page 12: Troubleshooting
Model MMC200 Multi-Material Cutter lower it down again to ensure the upper blade does 8. Return the machine to an upright position and not come down on top of the lower blade. recheck the shearing action of the blades. 5. Lower the upper blade all the way down and 9. - Page 13 Model MMC200 Specification Photos Knuckle with Key Left Blade Right Blade Holder Holder Upper Blade Lower Blade Holder Right Tension Left Tension Screw Screw Specification Photo 1 Firmly grasp both cap screws and push blade off of the knuckle key, lower Replace screw to use as a Handle blade and remove from machine.
- Page 14 Model MMC200 Specification Photos Lower Blade Holder Screws Specification Photo 4 Specification Photo 5 Production Automation • Eden Prairie, MN USA • Ph: 888-903-0333 • info@gotopac.com • www.gotopac.com • Fax 952-903-0315...
- Page 15 NOTES...
- Page 16 A u t IR1814 REV 04/08...