Table of Contents
Advertisement
Windows 2000
1
Rotate the power switch clockwise and hold it for ap-
proximately one second until the power indicator turns
on before releasing it.
CAUTION
Do not press any key or move the touch pad un-
til the Windows setup screen is displayed.
At the [Welcome to the Windows 2000 Setup Wizard],
2
press [Next].
3
After reading the License Agreement, select [I accept
this agreement] or [I don't accept this agreement], then
press [Next].
NOTE
If [I do not accept the agreement] is selected, the
Windows setup will be aborted.
Select settings for your region, then press [Next].
4
5
Enter your name and organization, then press [Next].
NOTE
<During the setup procedure after reinstalling only>
A f t e r y o u a c c e p t t h e a g r e e m e n t , t h e
[Windows Product Key] may be displayed. In this
case, input the Product Key and then select [Next].
Enter your computer name and administrator password,
6
then press [Next].
CAUTION
Remember this password! If the password is for-
gotten, Windows 2000 cannot be operated.
Input the correct date, time and time zone and press [Next].
7
You can also complete these settings at a later time.
<Only for models with LAN port>
8
NOTE
At the steps
8
and
your system administrator or the person in charge
of the network.
At the [Networking Settings], select [Typical
1)
settings], then press [Next].
2)
At the [Workgroup or Computer Domain], select
[No, this computer is not on a network, or is on a
network without a domain], then press [Next].
Press [Finish]. The computer will restart.
9
<For models with LAN port>
10
1)
At the [Network Identification Wizard], press [Next].
At the [Users of This Computer], select [Users must
2)
enter a user name and password to use this computer],
then press [Next].
3)
Press [Finish].
4)
Logon as the administrator.
5)
At [Found New Hardware Wizard], select [Cancel].
<For models with modem port>
1)
Logon as the administrator.
2)
At [Found New Hardware Wizard], select [Cancel].
10
, we recommend asking
<Only for models with CF-WWL282 Driver CD-ROM>
11
If the CD drive is not installed at this time, turn the
computer off, install the CD drive, and then turn the
computer on.
If [Found New Hardware Wizard] is displayed, select
[Cancel].
Set the CF-WWL282 Driver CD-ROM.
1)
Create"c:\util\drivers\aironet" folder. Select [Start]
- [Programs] - [Accessories] - [Command Prompt]
and input the following.
xcopy d:\ * . * c:\util\drivers\aironet /s
("d" is the CD drive letter. You can change the
letter to suit your preference.)
2)
Remove the CD-ROM and turn the computer off,
and then replace the CD drive with floppy disk
drive. Turn the computer on.
Logon as the Administrator.
3)
12
At [Found New Hardware Wizard], press [Next].
Select [Search for a suitable driver for my device] and
13
press [Next].
Select [Specify a location] and press [Next].
14
15
Input [c:\util\drivers\aironet] and press [OK].
Press [Next] and press [Finish].
16
Install the Aironet Client Utility (ACU).
17
The Aironet Client Utility (ACU) is used to configure
your client adapter for use in a wireless enterprise and
perform user-level diagnostics on your client adapter.
In[Start]-[Run], input [c:\util\drivers\aironet\utilities\acu\setup.exe]
and press [OK].
Follow the on-screen instructions.
<Only for models with LAN port>
18
1)
Select [Device Manager] in [Start] - [Settings] -
[Control Panel] - [System] - [Hardware].
Double-click [Intel 8255x-based PCI Ethernet Adapter
2)
(10/100)] in [Network adapters].
3)
Select [Driver] and press [Update Driver].
4)
Press [Next], then press [Next]
5)
Add the check mark for [Specify a location] and
press [Next].
Input [c:\util\drivers\lan] and press [OK].
6)
Add the check mark for [Install one of the other
7)
drivers] and press [Next].
8)
Select the driver for which the [Provider] is [Intel],
and then press [Next].
Each time [Digital Signature Not Found] is dis-
played, press [Yes].
Press [Finish] and press [Close].
9)
19
In [Start]-[Settings]-[Control Panel]-[Network and
Dial-up Connections], make necessary change.
The settings will vary for different network environ-
ments depending on the network system being used.
For more details, ask your system administrator or the
person in charge of the network.
(
"Common Notes for Windows 98/Windows NT/Win-
dows 2000" on next page)
Enter
5
Advertisement
Table of Contents
