4.8 Disassembly a side heater 5. Parts Exploded View and Replacement Parts List 5.1 Parts Exploded View : Body 5.2 Parts Exploded View : Packing 5.3 Replacement Parts List : SR-TMG10 / SR-TMG18 15 - 17 6. Detail Change Notice - 2 -...
SR-TMG10 / TMG18 2. WIRING DIAGRAM PCB lead wire C (Red) Thermal fuse lead wire A (Black) Should be above thermal fuse lead wire A and then goes below terminal of side heater lead wire D Side heater lead wire C (Black)
SR-TMG10 / TMG18 3. TROUBLESHOOTING GUIDE When receiving a rice boiler to be repaired, be sure to check that the main body is completely provide with the inner pan and the inner lid, ask the condition (phenmenon) of the trouble in detail. Before troubleshooting single parts, be sure to disconnect the power supply plug from the receptacle.
Page 6
SR-TMG10 / TMG18 Condition Troubleshooting Remedy • Excessive burning. Does the center thermostat operate (More than light brown) • Replace the center thermostat. properly? (Check with the evaporation test). • Seeing at Table 2. Are the parts on the P.C.B. mistake? Improper operation •...
Page 7
SR-TMG10 / TMG18 Table 2 Condition Troubleshooting Remedy • Rice is not boiling. • Replace the transformer. Is the transformer operating? (The indicating lamp does not come on) • Replace the P.C.B. complete. • Rice is not boiling. • Replace the relay.
SR-TMG10 / TMG18 4. TESTING PROCEDURE 4.1 Bubbling test Input the pan in the main body, lightly rotate the pan clockwise and counter clockwise to settle the pan on the heating plate properly. 1. Fill water until center area of the pan bottom is dipped and close the lid. Then turn on the boiling switch.
SR-TMG10 / TMG18 The above conditions are proper. Top view of pan Pan flange Holes on the tissue paper Tissue paper 4.3 Heat reserving test 1. Put approx. 1 liter of water and the thermometer [ repairing tool (mercury thermometer ASN-150H) ] in the pan, close the lid and turn on the boiling switch.
SR-TMG10 / TMG18 4.5 Inner enclosure and upper frame removal 1. As show in the figure, pry up three fastening hooks. Fixing the upper frame, turn the inner enclosure in the arrow direction. 2. The upper frame will be seperated from the inner enclosure and the upper frame.
SR-TMG10 / TMG18 4.6 Disassembly a control unit 1. Pull out the hinge shaft. 2. Pulling out wiring for lid heater and then pulling out outer lid ass’y. 3. Loosen a screw for bottom frame. 4. Loosen a screw for P.C.B. base 2 pcs.
SR-TMG10 / TMG18 4.7 Disassembly cast heater and thermostat case ass’y 1. Loosen a screw for cast heater. 2. Bending leg of thermostat. Screw 3. Lift a thermostat. 4.8 Disassembly a side heater 1. Pulling out a side heater and after that if will replace new side heater, keep a distance between 23 ~ 27 mm.
SR-TMG10 / TMG18 Important safety notice : Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer’s specified part. 5.3 Replacement Parts List : SR-TMG10 / SR-TMG18 Parts List MODEL / Q’TY REF.
SR-TMG10 / TMG18 Parts List MODEL / Q’TY REF. PART NAME PART NO. REMARK SR-TMG10 SR-TMG18 HINGE COVER ARE40H6162W9 DEW COLLECTOR ARK10H616-C0 BOTTOM FRAME ASS’Y ARH30T935W9U ARH30T934W9U FOOT RUBBER ARH90H663 NAME PLATE ARY30H935-CS ARY30H935-CP ARY30H935-MB ARY30H934-CS ARY30H934-CP ARY30H934-MB POWER CORD ASS’Y...
Page 17
SR-TMG10 / TMG18 Screws MODEL / Q’TY REF. PART NAME PART NO. REMARK SR-TMG10 SR-TMG18 TAPPING SCREW XTB4+10GFJ FOR HANDLE SEMS SCREW XYN4+C10FNS FOR CAST HEATER SEMS SCREW XYN4+C7FNS FOR WIRING SPRING WASHER XWA4BPW WITH XTN4+8FFU TAPPING SCREW XTN4+8FFJ FOR BODY EARTH...
SR-TMG10 / TMG18 DETAIL CHANGE NOTICE REVISION ITEM NO. PAGE DETAIL REMARK JAN. 2010 CHANGE PART NO. OF PAN CHANGE COATING FROM 1 TO 2 LAYER AUG. 2011 ADD NEW PAGE FOR CONTENT IT’S PAGE NO. 2 2 - 18 NEW RUNNING PAGE NO.