Page 1 Pacifica 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION versions are not expressly indicated in the text. Therefore, you should only consider the information which is related Dear Customer, to the trim level, engine, and version that you have Congratulations on selecting your new vehicle. Be assured purchased.
Page 7: Symbols
INTRODUCTION Since the specification of your vehicle depends on the items Symbols of equipment ordered, certain descriptions and illustra- Consult the following table for a description of the symbols tions may differ from your vehicle’s equipment. that may be used on your vehicle or throughout this The detailed index at the back of this Owner’s Manual Owner’s Manual: contains a complete listing of all subjects.
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INSTRUMENT PANEL .....10 REAR VIEW .
Page 10: Front View
8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Doors 2 — Windshield 5 — Wheels/Tires 3 — Exterior Mirrors 6 — Headlights...
Page 11: Rear View
GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Tail Lamps 2 — Rear Windshield Wiper 3 — Liftgate...
Page 12: Instrument Panel
10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 5 — Glove/Storage Compartment 2 — Multifunction Lever 6 — Ignition 3 — Instrument Cluster 7 — Steering Wheel 4 — Windshield Wiper Lever 8 — Headlight Switch...
Page 13: Interior
GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior Features 1 — Power Window/Door Lock Switches 5 — Door Handle 2 — Electronic Gear Selector 6 — Climate Control 3 — Uconnect Radio 7 — Center Console 4 — Switch Panel 8 — Seats...
Page 15 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .18 SENTRY KEY .
Page 16 14 GETTING TO KNOW YOUR VEHICLE ▫ Manual Sliding Side Door....42 ▫ Manually Folding Third Row Seats — If Equipped ......79 ▫...
Page 17 GETTING TO KNOW YOUR VEHICLE 15 ▫ Driver’s Outside Automatic Dimming Mirror — If ▫ Headlights On With Wipers — If Equipped ..96 Equipped ......90 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Automatic Uconnect 4C/4C NAV Climate Control HOOD .......142 Overview .
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ▫ Smoker’s Package Kit — If Equipped ..176 INTERNAL EQUIPMENT ....164 ▫...
Page 20: Keys
18 GETTING TO KNOW YOUR VEHICLE KEYS Key Fob Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system. The Remote Keyless Entry system consists of a key fob and Keyless Enter-N-Go feature if equipped.
Page 21 GETTING TO KNOW YOUR VEHICLE 19 Four Button Key Fob Five Button Key Fob...
Page 22 20 GETTING TO KNOW YOUR VEHICLE Six Button Key Fob Seven Button Key Fob To Unlock The Doors NOTE: Uconnect Settings lets you program the system to unlock either the driver’s side doors on the first push (default) or unlock all doors on the first push of the unlock button on the key fob.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 hazard lights will flash to acknowledge the unlock signal. The illuminated entry system will be activated. Second Push Unlock This feature lets you program the system to unlock either the driver’s side doors or all doors on the first push of the First Push Unlock unlock button on the key fob.
Page 24 22 GETTING TO KNOW YOUR VEHICLE Emergency Key Feature To remove the emergency key, press the mechanical button on the side of the key fob with your thumb and pull the The key fob also contains an emergency key, which stores emergency key out with your other hand while pushing in the bottom of the key fob.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 Key Fob Battery Replacement 1. Remove the emergency key by pushing the mechanical release button on the side of the key fob with your The recommended replacement battery is one CR2032 thumb and then pull the key out with your other hand. battery.
Page 26 24 GETTING TO KNOW YOUR VEHICLE Programming Additional Key Fob If you do not have a programmed key fob, contact your authorized dealer for details. Request For Additional Remote Controls NOTE: Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 KeySense Features — If Equipped This feature provides the vehicle owner with the ability to customize vehicle settings that can be applied to determine the driving experience for other drivers of the vehicle. The vehicle settings are protected by a unique 4-digit PIN, which the vehicle owner creates when accessing the spe- cific settings for the first time.
Page 28: Ignition Switch
26 GETTING TO KNOW YOUR VEHICLE The following features are always enabled when this key is 2. This device must accept any interference received, in- in use: cluding interference that may cause undesired opera- tion. • Entertainment Audio Muted if 1st row occupied Seat Belts are not Fastened NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the...
Page 29 GETTING TO KNOW YOUR VEHICLE 27 ON/RUN • Driving position. • All the electrical devices are available. START • Start the vehicle. The engine only runs in the ON/RUN ignition position or from a remote start request. In case the ignition switch does not change with the push of a button, the key fob may have a low or dead battery.
Page 30 28 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector.
Page 31: Remote Starting System - If Equipped
GETTING TO KNOW YOUR VEHICLE 29 • With remote start, the engine will only run for 15 REMOTE STARTING SYSTEM — IF EQUIPPED minutes (timeout) unless the ignition key is placed in the ON/RUN position. This system uses the key fob to start the engine •...
Page 32: Remote Start Cancel Message - If Equipped
30 GETTING TO KNOW YOUR VEHICLE The message will stay active until the ignition is placed in WARNING! the ON/RUN position. • Do not start or run an engine in a closed garage or To Enter Remote Start Mode confined area. Exhaust gas contains Carbon Monox- Push and release the Remote Start button on the key fob ide (CO) which is odorless and colorless.
Page 33: To Exit Remote Start Mode Without Driving The Vehicle
GETTING TO KNOW YOUR VEHICLE 31 To Exit Remote Start Mode Without Driving The Remote Start Comfort Systems — If Equipped Vehicle When Remote Start is activated, the Climate Control, Push and release the Remote Start button one time or allow vented seats (if equipped) are also activated in tempera- the remote start cycle to complete the entire 15-minute tures above 80°...
Page 34: Sentry Key
32 GETTING TO KNOW YOUR VEHICLE SENTRY KEY Customer Key Programming The Sentry Key Immobilizer system prevents unauthorized Programming key fobs may be performed at your autho- operation by disabling the vehicle. The system does not rized dealer. need to be armed or activated. Operation is automatic, Replacement Keys regardless of whether the vehicle is locked or unlocked.
Page 35: General Information
GETTING TO KNOW YOUR VEHICLE 33 General Information lamps and/or turn signals will flash, and the vehicle security light in the instrument cluster will flash. The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: Rearming Of The System This device complies with Part 15 of the FCC Rules and If something triggers the alarm, and no action is taken to...
Page 36: To Disarm The System
34 GETTING TO KNOW YOUR VEHICLE exterior zone (refer to Keyless Enter-N-Go — Passive NOTE: Entry in Getting To Know Your Vehicle for further • The driver’s door key cylinder and the liftgate button on information). the key fob cannot arm or disarm the vehicle security •...
Page 37: Doors
GETTING TO KNOW YOUR VEHICLE 35 If the vehicle security alarm is armed and the battery becomes disconnected, the vehicle security alarm will remain armed when the battery is reconnected; the exterior lights will flash, and the horn will sound. If this occurs, disarm the vehicle security alarm.
Page 38 36 GETTING TO KNOW YOUR VEHICLE Manual Door Lock Rocker Switch Manual Rear Door Lock Location 1 — Door Handle 2 — Manual Door Lock If the door lock button is locked (no ribbing is visible) when you shut the door, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door.
Page 39: Central Lock/Unlock - If Equipped
GETTING TO KNOW YOUR VEHICLE 37 Central Lock/Unlock — If Equipped WARNING! A power door lock switch is on each front door trim panel. • For personal security and safety in the event of a Use this switch to lock or unlock the doors. collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle.
Page 40: Unlock Doors Automatically On Exit - If Equipped
38 GETTING TO KNOW YOUR VEHICLE allow the locks to operate. A chime will sound if the NOTE: ignition is in the ACC or ON/RUN position and a door is • Passive Entry may be programmed ON/OFF. Refer to open, as a reminder to place the ignition in the OFF “Uconnect Settings”...
Page 41 GETTING TO KNOW YOUR VEHICLE 39 To Unlock From The Driver’s Side: To Unlock From The Passenger Side: With a valid key fob within 5 ft (1.5 m) of the driver’s door With a valid key fob within 5 ft (1.5 m) of the passenger handle, grab the driver’s front door handle to unlock the door handle, grab the front passenger door handle to drivers side doors (driver/sliding door) automatically.
Page 42 40 GETTING TO KNOW YOUR VEHICLE • A lock request is made by the door panel switch while To Enter The Liftgate the door is open. With a valid key fob within 5 ft (1.5 m) of the liftgate, cycle When any of these situations occur, after all open doors are the handle to open the liftgate and pull the liftgate open shut, the FOBIK-Safe search will be executed.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 To Lock The Vehicle’s Doors With one of the vehicle’s key fobs within 5 ft (1.5 m) of the driver or passenger front door handle, push the door handle lock button to lock all four doors and the liftgate. Do NOT Grab The Door Handle When Locking NOTE: •...
Page 44: Manual Sliding Side Door
42 GETTING TO KNOW YOUR VEHICLE Manual Sliding Side Door The sliding door may be opened from the inside or the outside. Pull outward on the exterior handle to open the sliding door. The sliding door inside handle functions by rocking forward and back.
Page 45: Power Sliding Side Door - If Equipped
GETTING TO KNOW YOUR VEHICLE 43 • There is a hold-open latch that is activated when the – On the outside handle sliding door is fully opened. This latch will keep your Push the button on the key fob twice within five sliding door open on any incline.
Page 46 44 GETTING TO KNOW YOUR VEHICLE There are power sliding side door switches located on the B-Pillar trim panel, just in front of the power sliding door for the rear seat passengers. To operate the sliding door manually with the handles or to avoid unintentional operation of the power sliding doors from the rear seats, push the power sliding door power off button, located in the overhead console, to remove power...
Page 47 GETTING TO KNOW YOUR VEHICLE 45 WARNING! Personal injury or cargo damage may occur if caught in the path of the sliding door. Make sure the door path is clear before closing the door. WARNING! Before driving off, check the instrument cluster for a sliding door or door open message or warning indica- tor.
Page 48: Hands-Free Sliding Doors - If Equipped
46 GETTING TO KNOW YOUR VEHICLE Hands-Free Sliding Doors — If Equipped NOTE: • To open the Hands-Free Sliding Doors requires a valid Passive Entry key fob within 5 ft (1.5 m) of the door handle. If a valid Passive Entry key fob is not within 5 ft (1.5 m), the door will not respond to any kicks.
Page 49 GETTING TO KNOW YOUR VEHICLE 47 To Engage The Child Protection Door Lock NOTE: • After engaging (or disengaging) the Child Protection 1. Open the sliding side door. Door Lock, always test the inside door handle with the 2. On the rear of the sliding door, slide the Child Protection sliding door closed to make certain the Child Protection Door Lock control inward (toward the vehicle) to en- Door Lock is in the desired position.
Page 50: Seats
48 GETTING TO KNOW YOUR VEHICLE To Disengage The Child Protection Door Lock WARNING! (Continued) 1. Open the sliding side door. these areas are more likely to be seriously injured or killed. 2. Slide the Child Protection Door Lock control outward •...
Page 51 GETTING TO KNOW YOUR VEHICLE 49 Manual Front Adjuster move forward and rearward on the seat to be sure that the seat adjusters have latched. Both front seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat WARNING! cushion at the front edge of each seat.
Page 52: Manual Adjustment (Rear Seats)
50 GETTING TO KNOW YOUR VEHICLE Manual Adjustment (Rear Seats) WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured.
Page 53: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 51 Power Adjustment (Front Seats) — If Equipped Some models may be equipped with eight-way power seats for the driver and front passenger. The power seat switches are located on the outboard side of the seat. The switches control the movement of the seat cushion and the seatback.
Page 54 52 GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. Push • Adjusting a seat while driving may be dangerous. the seat switch forward or rearward, and the seat will Moving a seat while driving could result in loss of move in the direction of the switch.
Page 55: Power Adjustment (Rear Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 53 Push the switch forward or rearward to increase or de- WARNING! crease the lumbar support. Push the switch upward or • Adjusting a seat while driving may be dangerous. downward to raise or lower the lumbar support. Moving a seat while driving could result in loss of Power Adjustment (Rear Seats) —...
Page 56 54 GETTING TO KNOW YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Third Row Power Recline —...
Page 57 GETTING TO KNOW YOUR VEHICLE 55 NOTE: • The outer head restraints will lower automatically as necessary when the power seat begins to move. • The center head restraint raises and lowers manually but will not lower automatically. • The head restraint can also be lowered manually using the pull strap located at the back of the seat.
Page 58 56 GETTING TO KNOW YOUR VEHICLE To move the selected seat(s) back in the forward or reverse direction, push and hold the Fold forward or rearward button. Release the button when the desired position is reached. NOTE: 1. Disconnect the center shoulder belt from the mini- buckle before attempting to fold/stow the power third row seats.
Page 59: Driver Memory Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE 57 Driver Memory Seat — If Equipped Programming The Memory Feature The Memory Buttons (1) and (2) on the driver’s door panel To create a new memory profile, perform the following: can be programmed to recall the driver’s seat, outside 1.
Page 60 58 GETTING TO KNOW YOUR VEHICLE Linking And Unlinking The Remote Keyless Entry 5. Push and release the lock button on the key fob within Key Fob To Memory 10 seconds. Your key fob can be programmed to recall one of two NOTE: Your key fob can be unlinked to your memory pre-programmed memory profiles by pushing the unlock settings by pushing the set (S) button, and within 10...
Page 61: Heated Seats
GETTING TO KNOW YOUR VEHICLE 59 • The Easy Entry/Easy Exit feature is disabled when the NOTE: Pushing the mirror adjust switch will cancel the memory mirror recall. driver seat position is less than 0.9 inches (22.7 mm) forward of the rear stop. At this position, there is no Easy Entry/Exit Seat (Available With Memory Seat benefit to the driver by moving the seat for Easy Exit or Only)
Page 62 60 GETTING TO KNOW YOUR VEHICLE • Press the heated seat button a second time to turn WARNING! the LO setting ON. • Persons who are unable to feel pain to the skin • Press the heated seat button a third time to turn the because of advanced age, chronic illness, diabetes, heating elements OFF.
Page 63: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 61 operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after approximately 60 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change.
Page 64: Stow 'N Go Seating
62 GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With Remote Start WARNING! On models that are equipped with remote start, the venti- During power seat operation, personal injury or cargo lated seats can be programed to come on during a remote damage may occur.
Page 65 GETTING TO KNOW YOUR VEHICLE 63 Using the Auto Advance ‘n Return Feature NOTE: • To abort seat operation while seat is in motion, push the NOTE: Auto Advance ‘n Return button, or push the front power • The button is only functional when the power sliding seat button to stop the seat movement.
Page 66 64 GETTING TO KNOW YOUR VEHICLE Second Row Stow ’n Go For Manual Seats: To stow the seat in the floor, move the front seat all the way forward using the manual seat adjustment bar. Move the seat back all the way forward using the recliner handle located on the outboard side of the cushion.
Page 67 GETTING TO KNOW YOUR VEHICLE 65 2. Pull the latch located near the second row seat to open 3. Pull the floor panel and position it toward the front seats the floor panel. while folding the top half down and rest it against the front seats.
Page 68 66 GETTING TO KNOW YOUR VEHICLE 4. Fold the armrest upward and stow the seat by grabbing 5. Push down on the seat back to lock the seat in the tub. the strap on the lower part of the seat back, and guide the seat into the tub.
Page 69 GETTING TO KNOW YOUR VEHICLE 67 6. Close the floor by pulling the floor panel backwards by the bottom corner edge of the panel. Push To Lock 8. Readjust the front seat as needed. Extend Floor Panel WARNING! 7. Push down on floor panel to lock into place. In a collision, serious injury could result if the seat storage bin covers are not properly latched: •...
Page 70 68 GETTING TO KNOW YOUR VEHICLE CAUTION! • The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. • Do not sit on the second row seat when it is in the stowed position with the seatback upright otherwise damage to the seat may occur.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 2. Pull the latch located near the second row seat to open 3. Pull the floor panel and position it toward the front seats the floor panel. while folding the top half down and rest it against the front seats.
Page 72 70 GETTING TO KNOW YOUR VEHICLE 4. Pull the strap located on the seat and pull the seat out of 5. To position the floor panel back into its original state, the storage bin. Push the seat rearward making sure that grab the bottom corner and extend it outward.
Page 73 GETTING TO KNOW YOUR VEHICLE 71 6. Lay the floor panel flat and push down until it clicks 7. Readjust the front seat as needed. into position. Replace the floor mat as needed. WARNING! • In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments.
Page 74: Easy Entry
72 GETTING TO KNOW YOUR VEHICLE Easy Entry Easy Tilt Seat — With Or Without Child Seat Installed The 2nd row seats can be tilted forward for easy entry into the third row with or without a child seat installed. 1.
Page 75 GETTING TO KNOW YOUR VEHICLE 73 Easy Entry — With The Seat Folded Flat Pull the strap on the back of the seat and the seat will tilt forward. The seats can be folded and tilted for more accessibility for passengers to enter and exit the third row.
Page 76: Fold-Flat - Quad Seats
74 GETTING TO KNOW YOUR VEHICLE Exit For 3rd Row Passengers Fold-Flat — Quad Seats For passengers seated in the third row, there is a pull strap To fold the seat, lift the recliner lever to the full upward located on the outboard side of the seat near the bottom of position and push the seatback forward until it rests on the the seat back.
Page 77: Second Row Removable 8Th Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE 75 NOTE: Second Row Removable 8th Seat — If Equipped • The seatback may lock into the fold flat position. Use the While the 8th seat does not stow in the floor, it is foldable recline lever to unlock the seatback.
Page 78: Second Row Bench Seat - If Equipped
76 GETTING TO KNOW YOUR VEHICLE Release Strap In Floor Detent Guides NOTE: Seat can be removed easier with one outboard seat WARNING! stowed in the load floor. If not properly latched, the seat could become loose. To reinstall the seat, align the seat into the detent positions Personal injuries could result.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 push back to the desired position and release the lever. Removing The Bench Seat Lean forward and lift the lever to return the seatback to its 1. Adjust the driver and passenger seats forward to allow normal position.
Page 80 78 GETTING TO KNOW YOUR VEHICLE 3. Pull the release strap located behind the seat, in the center near the floor to release the latches. Tilt Bench Seat Forward NOTE: Release Strap Location • Due to the weight of the bench seat, it is recommended 4.
Page 81: Manually Folding Third Row Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 79 NOTE: Push downward to ensure the rear latches are in 2. Pull release strap marked “1” to release the anchors. the locked position. 3. Lift the recline handle and return the seat back to the seating position.
Page 82 80 GETTING TO KNOW YOUR VEHICLE 3. Pull release strap marked “2” and tumble the seat rearward into the storage bin. Stowed Third Row Seat To Unfold Third Row Seats Strap “2” 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 Assist Straps Strap “2” 2. Pulling strap “2” releases the seatback to return to its 3. Raise the head restraint to its upright position. full upright position. WARNING! • In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments.
Page 84: Plastic Grocery Bag Retainer Hooks
82 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Head restraints should never be adjusted while the their upright positions when the seat is to be occu- pied. vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could Plastic Grocery Bag Retainer Hooks cause serious injury or death in the event of a...
Page 85 GETTING TO KNOW YOUR VEHICLE 83 restraint, put the head restraint posts into the holes and push downward. Then, adjust the head restraint to the appropriate height. Normal Position Front Head Restraint 1 — Adjustment Button 2 — Release Button...
Page 86: Head Restraints - Second Row Quad Seats
84 GETTING TO KNOW YOUR VEHICLE Head Restraints — Second Row Quad Seats The second row outboard head restraints, as well as the removable 8th passenger seat (if equipped) have adjustable head restraints. To raise the head restraint, pull upward on the head restraint.
Page 87: Head Restraints - Third Row
GETTING TO KNOW YOUR VEHICLE 85 WARNING! • A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re- moved head restraints in a location outside the occupant compartment.
Page 88 86 GETTING TO KNOW YOUR VEHICLE NOTE: To remove the center head restraint, raise it as far as it can go. Then, push the release button and the adjustment button at the base of each post while pulling the head restraint up.
Page 89: Power Folding Third Row Head Restraints - If Equipped
GETTING TO KNOW YOUR VEHICLE 87 Power Folding Third Row Head Restraints — If STEERING WHEEL Equipped Tilt/Telescoping Steering Column For improved visibility, the third row outboard head This feature allows you to tilt the steering column upward restraints can be folded using the Uconnect System. or downward.
Page 90: Heated Steering Wheel - If Equipped
88 GETTING TO KNOW YOUR VEHICLE • Press the heated steering wheel button steering column in position, push the lever upward until once to turn fully engaged. the heating element on. • Press the heated steering wheel button a second time WARNING! to turn the heating element off.
Page 91: Mirrors
GETTING TO KNOW YOUR VEHICLE 89 WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. MIRRORS Inside Day/Night Mirror —...
Page 92: Outside Mirrors
90 GETTING TO KNOW YOUR VEHICLE dimming feature is activated. The sensor to the right of the Outside Mirrors button does not illuminate. To receive maximum benefit, adjust the outside mirror(s) to NOTE: This feature is disabled when the vehicle is in center on the adjacent lane of traffic with a slight overlap of REVERSE.
Page 93: Conversation Mirror
GETTING TO KNOW YOUR VEHICLE 91 Conversation Mirror Power Mirrors — If Equipped Located in the overhead console there is a conversation The power mirror controls are located on the driver-side mirror to view all the passengers in the vehicle. Push the door trim panel.
Page 94: Outside Mirrors Folding Feature
92 GETTING TO KNOW YOUR VEHICLE Left and Right side power mirror preselected positions can Tilt Side Mirrors In Reverse (Available With be controlled by the optional Driver Memory Seat Feature. Memory Seat Only) — If Equipped Refer to “Driver Memory Seat” in “Seats” for further Tilt Side Mirrors In Reverse provides automatic outside information.
Page 95: Illuminated Vanity Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 93 • The mirrors come out of the unfolded position. • The mirrors shake and vibrate at normal driving speeds. To reset the power folding mirrors: fold and unfold them by pushing the button (this may require multiple button pushes).
Page 96: Exterior Lights
94 GETTING TO KNOW YOUR VEHICLE EXTERIOR LIGHTS Headlight Switch The headlight switch is located on the left side of the Multifunction Lever instrument panel. The switch controls the operation of the The multifunction lever is located on the left side of the headlights, parking lights, instrument panel lights, interior steering column.
Page 97: Daytime Running Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 95 Rotate the headlight switch to the third detent for head- NOTE: Broken, muddy, or obstructed headlights and tail- light, parking light and instrument panel operation. lights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).
Page 98: Flash-To-Pass
96 GETTING TO KNOW YOUR VEHICLE 2. Pull the multifunction lever toward you to switch the NOTE: The engine must be running before the headlights headlights from the high beam to the low beam position. will come on in the Automatic mode. 3.
Page 99: Lights-On Reminder
GETTING TO KNOW YOUR VEHICLE 97 When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60, or 90 seconds or not remain on. To change the timer setting, select the proper setting through the Uconnect System. Refer to “Uconnect Settings”...
Page 100: Lane Change Assist - If Equipped
98 GETTING TO KNOW YOUR VEHICLE Turn Signal Warning INTERIOR LIGHTS If the vehicle electronics sense that the vehicle has traveled Courtesy/Interior Lighting for about 1 mile (1.6 km) with the turn signals on, a chime The courtesy light switches are used to turn the courtesy will sound and a message will display in the cluster to alert lights on/off.
Page 101 GETTING TO KNOW YOUR VEHICLE 99 NOTE: The courtesy lights also function as reading lights. Push the lens to turn these lights on while inside the vehicle. Push • Before exiting the vehicle, make sure that the interior the lens a second time to turn each light off. lights are turned off.
Page 102 100 GETTING TO KNOW YOUR VEHICLE Ambient Light Control — If Equipped Interior Lighting Off Rotate the ambient dimmer control upward or downward Rotate the right (instrument panel) dimmer control to the to increase or decrease the brightness of the ambient light off position (extreme bottom).
Page 103: Windshield Wiper And Washers
GETTING TO KNOW YOUR VEHICLE 101 (dome off), and the cluster, radio and instrument lighting WINDSHIELD WIPER AND WASHERS go to their lowest dimmable setting. Windshield Wiper Operation The wipers and washers are operated by a switch within the wiper lever. Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation.
Page 104 102 GETTING TO KNOW YOUR VEHICLE NOTE: Always remove any buildup of snow that prevents Windshield Washers the windshield wiper blades from returning to the off To use the washer, pull the lever rearward toward you and position. If the windshield wiper switch is turned off and hold while spray is desired.
Page 105: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE 103 • Use of Rain-X or products containing wax or silicone Rain Sensing Wipers — If Equipped may reduce rain sensor performance. This feature senses rain or snowfall on the windshield and • The Rain Sensing feature can be turned on and off automatically activates the wipers for the driver.
Page 106: Rear Wiper And Washer
104 GETTING TO KNOW YOUR VEHICLE • Neutral Wipe Inhibit — The Rain Sensing feature will Rear Wiper And Washer not operate when the ignition is ON, when the transmis- Rear Windshield Wiper Operation sion gear selector is in the NEUTRAL position and the Rotate the windshield wiper lever center ring upwards to vehicle speed is less than 3 mph (5 km/h), unless the operate one of two modes for the rear window wiper:...
Page 107: Climate Controls
GETTING TO KNOW YOUR VEHICLE 105 CLIMATE CONTROLS Manual Climate Controls Overview Uconnect 4 With 7–inch Display Manual Climate Controls...
Page 108 106 GETTING TO KNOW YOUR VEHICLE Uconnect 4/4C NAV With 8.4–inch Display Manual Climate Controls...
Page 109 GETTING TO KNOW YOUR VEHICLE 107 Manual Climate Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 110 108 GETTING TO KNOW YOUR VEHICLE Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase.
Page 111 GETTING TO KNOW YOUR VEHICLE 109 Icon Description SYNC Button — If Equipped Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger tempera- ture setting with the driver temperature setting.
Page 112 110 GETTING TO KNOW YOUR VEHICLE Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 Icon Description Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF. Controlling The Rear Climate Controls From The Front MTC Display/Touchscreen The Three-Zone MTC system allows for adjustment of the rear climate controls from the front MTC display/ touchscreen.
Page 114 112 GETTING TO KNOW YOUR VEHICLE To change the rear system settings: • Press the REAR CLIMATE button on the touchscreen to change control to rear control mode, Rear display appears. Control functions now operate rear system. • To return to the Front screen on the Uconnect system, press the Front Climate button on the touchscreen.
Page 115 GETTING TO KNOW YOUR VEHICLE 113 Icon Description SYNC Button — If Equipped Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indica- tor is illuminated when this feature is enabled. SYNC is used to synchronize the front and rear passenger temperature settings with the driver temperature setting.
Page 116 114 GETTING TO KNOW YOUR VEHICLE Icon Description Panel Mode Panel Mode Press this button on the touchscreen to change the air distribution mode to Panel Mode. In Panel Mode, air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air.
Page 117 GETTING TO KNOW YOUR VEHICLE 115 Rear Manual Temperature Control The rear MTC system has floor air outlets at the rear right side of the 3rd Row seats and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 118 116 GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 119 GETTING TO KNOW YOUR VEHICLE 117 Icon Description Rear Climate Control/Blower Off To manually set the rear blower controls to off, press the Rear Climate Control/Blower Off button. CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille, located in floor under the passengers’...
Page 120: Automatic Uconnect 4 Climate Control Overview
118 GETTING TO KNOW YOUR VEHICLE Automatic Uconnect 4 Climate Control Overview Uconnect 4 With 7–inch Display Automatic Temperature Controls...
Page 121: Automatic Uconnect 4C/4C Nav Climate Control Overview
GETTING TO KNOW YOUR VEHICLE 119 Automatic Uconnect 4C/4C NAV Climate Control Overview Uconnect 4C/4C With 8.4–inch Display NAV Automatic Climate Controls...
Page 122 120 GETTING TO KNOW YOUR VEHICLE Automatic Climate Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 123 GETTING TO KNOW YOUR VEHICLE 121 Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase.
Page 124 122 GETTING TO KNOW YOUR VEHICLE Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. SYNC is used to synchronize the front and rear pas- senger temperature settings.
Page 125 GETTING TO KNOW YOUR VEHICLE 123 Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 126 124 GETTING TO KNOW YOUR VEHICLE Icon Description Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
Page 127 GETTING TO KNOW YOUR VEHICLE 125 Uconnect 4 Front ATC Panel Rear Control Display Uconnect 4C/4C NAV Front ATC Panel Rear Control Display...
Page 128 126 GETTING TO KNOW YOUR VEHICLE Icon Description REAR AUTO Rear Auto Button Automatically controls the rear interior cabin temperature by adjusting airflow distribution and amount. Performing this function causes the system to switch between manual mode and auto- matic modes. Refer to “Automatic Operation” within this section for more information. Rear Lock Button Press and release to lock out the rear manual temperature controls from adjusting the rear tem- perature and blower settings.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 Icon Description SYNC Button — If Equipped Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indica- tor is illuminated when this feature is enabled. SYNC is used to synchronize the front and rear passenger temperature settings with the driver temperature setting.
Page 130 128 GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Press this button on the touchscreen to change the air distribution mode to Bi-Level Mode. In Bi-Level Mode, air comes from both the headliner outlets and the floor outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 131 GETTING TO KNOW YOUR VEHICLE 129 1. Adjust the rear blower, rear temperature and the rear NOTE: modes to suit your comfort needs. • It is not necessary to move the temperature settings. The system automatically adjusts the temperature, mode and 2.
Page 132 130 GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. Rear Temperature Control • Rear Passenger Temperature Up Button To change the temperature in the rear of the vehicle, push temperature control up button to raise the temperature. The rear temperature settings are displayed in control head.
Page 133: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE 131 Icon Description Rear Climate Control/Blower Off To manually set the rear blower controls to off, press the Rear Climate Control/Blower Off button. • If fog or mist appears on the windshield or side glass, Climate Control Functions select Defrost Mode and adjust blower speed if needed.
Page 134: Automatic Temperature Control (Atc) - If
132 GETTING TO KNOW YOUR VEHICLE Automatic Temperature Control (ATC) — If feature. Refer to the “Uconnect Settings” in “Multime- Equipped dia” for further information. To provide you with maximum comfort in the Automatic Automatic Operation mode during cold start-ups, the blower fan will remain on 1.
Page 135 GETTING TO KNOW YOUR VEHICLE 133 Winter Operation Window Fogging To ensure the best possible heater and defroster perfor- Vehicle windows tend to fog on the inside in mild, rainy, mance, make sure the engine cooling system is functioning and/or humid weather. To clear the windows, select De- properly and the proper amount, type, and concentration frost or Mix mode and increase the front blower speed.
Page 136: Windshield
134 GETTING TO KNOW YOUR VEHICLE Outside Air Intake Operating Tips Chart Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains.
Page 137: Windows
GETTING TO KNOW YOUR VEHICLE 135 WINDOWS Power Windows You can control either the front or rear windows using controls located on the driver’s door trim panel. The driver may lock out the rear power windows by pushing the bar control just below the power window controls.
Page 138 136 GETTING TO KNOW YOUR VEHICLE Auto Up Feature With Anti-Pinch Protection — If Equipped The front driver and front passenger controls may be equipped with an Auto Up feature. Lift the window control fully upward to the second detent, release, and the window will go up automatically.
Page 139 GETTING TO KNOW YOUR VEHICLE 137 The controls will operate only when the ignition switch is WARNING! in the ON/RUN or ACC position and during power accessory delay. There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear NOTE: The controls will not operate if the driver has your arms, hands, fingers and all objects from the activated the Power Window Lockout.
Page 140: Tri-Pane Panoramic Sunroof - If Equipped
138 GETTING TO KNOW YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 141: Opening Sunroof
GETTING TO KNOW YOUR VEHICLE 139 NOTE: If the sunshade is in the closed position when the WARNING! (Continued) open switch is pushed, the sunshade will automatically ON/RUN mode. Occupants, particularly unattended cycle to the halfway open position prior to the sunroof children, can become entrapped by the power sun- opening.
Page 142: Wind Buffeting
140 GETTING TO KNOW YOUR VEHICLE The sunroof will close fully and stop automatically. This is Power Sun Shade — If Equipped called “Express Close.” During Express Close operation, Opening Power Shade — Express Mode any other actuation of the switch will stop the sunroof. Push the shade switch rearward and release it within one Manual Mode second and the shade will open automatically from any...
Page 143: Pinch Protect Feature
GETTING TO KNOW YOUR VEHICLE 141 and stop automatically. This is called “Express Close”. Sunroof Maintenance During Express Close operation, any other actuation of the Use only a non-abrasive cleaner and a soft cloth to clean the switch will stop the shade. glass panel.
Page 144: Hood
142 GETTING TO KNOW YOUR VEHICLE HOOD 3. Push the safety latch release lever toward the passenger side of the vehicle. The safety latch is located behind the Opening center front edge of the hood. The hood release lever (to open the primary latch) and safety latch (to open the secondary latch) must be released to open the hood.
Page 145: Closing
GETTING TO KNOW YOUR VEHICLE 143 • Vehicle must be at a stop and the transmission must be CAUTION! in PARK. To prevent possible damage, do not slam the hood to Closing close it. Lower hood to approximately 12 inches (30 cm) 1.
Page 146 144 GETTING TO KNOW YOUR VEHICLE Unlock Liftgate Using Key Fob Unlock Liftgate Using Passive Entry The key fob and the overhead console button will release NOTE: If 1st Press of key fob Unlocks “All Doors” is the liftgate when the liftgate is locked. The outside handle programmed in Uconnect Settings, all doors will unlock requires the liftgate to be unlocked.
Page 147: Closing
GETTING TO KNOW YOUR VEHICLE 145 Closing Power Liftgate — If Equipped To Close The Liftgate The power liftgate may be opened or closed in several ways: Grasp the liftgate closing handle and initiate lowering the • Overhead console liftgate button liftgate.
Page 148 146 GETTING TO KNOW YOUR VEHICLE (if equipped) will unlock and open the liftgate, with a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate handle. NOTE: • To open the liftgate, the Hands-Free Liftgate foot activa- tion (if equipped) requires a valid Passive Entry key fob within 5 ft (1.5 m) of the door handle.
Page 149: Hands-Free Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE 147 To Close The Liftgate Hands-Free Liftgate — If Equipped The liftgate can also be closed using the Rear Interior Power Liftgate button (if equipped), located in the upper left trim in the liftgate opening. Hands-Free Liftgate Activation Zone To open the liftgate using hands-free activation, use a straight in and out kicking motion under the vehicle...
Page 150 148 GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With A Trailer Tow Package NOTE: To open the Hands-Free Liftgate requires a valid Passive Entry key fob within 5 ft (1.5 m) of the door handle. NOTE: If your vehicle is equipped with the Trailer Tow If a valid Passive Entry key fob is not within 5 ft (1.5 m), the Package, the hands-free activation zone(s) for the Power liftgate will not respond to any kicks.
Page 151 GETTING TO KNOW YOUR VEHICLE 149 • If the power liftgate encounters multiple obstructions Gas props support the liftgate in the open position. How- within the same cycle, the system will automatically ever, because the gas pressure drops with temperature, it stop.
Page 152: Cargo Area Features
150 GETTING TO KNOW YOUR VEHICLE Cargo Area Features Stow ‘n Vac Integrated Vacuum — If Equipped Your vehicle may be equipped with an integrated vacuum Cargo Area Storage system. This vacuum is for in-vehicle use only and should When the third row seats are not in the stowed position, only be used on dry materials and on in-vehicle surfaces.
Page 153 GETTING TO KNOW YOUR VEHICLE 151 WARNING! (Continued) WARNING! (Continued) • Do not leave the key fob in or near the vehicle, or in a from flammable liquids may form an explosive mix- location accessible to children, and do not leave the ture with air and can be ignited by heat, sparks, or ignition of a vehicle equipped with Keyless Enter- flames.
Page 154 152 GETTING TO KNOW YOUR VEHICLE Engine Running (ON) Operation - For more than 10 WARNING! minutes of operation • Position vehicle outdoors and fully open all side This equipment incorporates parts such as switches, motors, or the like that tend to produce arcs or sparks windows.
Page 155 GETTING TO KNOW YOUR VEHICLE 153 • Hose Extension — Use to add another 12 ft of usable 3. Install desired attachment if needed. length to the vacuum hose. Hose extension is located in the upper access panel behind the third row seat on the driver’s side.
Page 156 154 GETTING TO KNOW YOUR VEHICLE WARNING! For in vehicle use ONLY. To reduce the risk of fire, serious injury or death: • Do not use vacuum while vehicle is in motion or while driving. • Do not vacuum wet surfaces or any liquids.
Page 157 GETTING TO KNOW YOUR VEHICLE 155 5. When finished, push power button to turn vacuum off WARNING! (Continued) and store vacuum hose and any attachments. • Do not put any object into openings. Do not use with 6. Before exiting the vehicle: any opening blocked;...
Page 158 156 GETTING TO KNOW YOUR VEHICLE stale odors, allow both to dry completely before rein- stalling in your vehicle. If filter has tears, holes or other damage and needs to be replaced, please contact your authorized dealer. • If there are any other issues with your vacuum, contact your authorized dealer.
Page 159: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE 157 Hose Access Port 2. Return to vacuum nozzle storage location located be- hind the sliding door. The hose access port is located behind the upper access panel behind the third row seat on the driver’s side. 3.
Page 160: Before You Begin Programming Homelink
158 GETTING TO KNOW YOUR VEHICLE The HomeLink buttons, located on the driver’s sunvisor, battery be placed in the hand-held transmitter of the device designate the three different HomeLink channels. The that is being programmed to the HomeLink system. HomeLink indicator is located above the center button. To erase the channels, place the ignition in the ON/RUN position, and push and hold the two outside HomeLink buttons (I and III) for up to 20 seconds or until the orange...
Page 161 GETTING TO KNOW YOUR VEHICLE 159 4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and then rapidly after HomeLink has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.
Page 162 160 GETTING TO KNOW YOUR VEHICLE To program the remaining two HomeLink buttons, repeat 3. Press and hold the HomeLink button you want to each step for each remaining button. DO NOT erase the program while you press and hold the hand-held trans- channels.
Page 163: Canadian/Gate Operator Programming
GETTING TO KNOW YOUR VEHICLE 161 2. Press and hold the desired HomeLink button until the 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) indicator light begins to flash after 20 seconds. Do not away from the HomeLink button you wish to program release the button.
Page 164: Using Homelink
162 GETTING TO KNOW YOUR VEHICLE If you unplugged the garage door opener/device for Security programming, plug it back in at this time. It is advised to erase all channels before you sell or turn in Reprogramming A Single HomeLink Button (Canadian/ your vehicle.
Page 165: General Information
GETTING TO KNOW YOUR VEHICLE 163 General Information WARNING! The following regulatory statement applies to all Radio • Vehicle exhaust contains carbon monoxide, a danger- Frequency (RF) devices equipped in this vehicle: ous gas. Do not run your vehicle in the garage while This device complies with Part 15 of the FCC Rules and programming the transceiver.
Page 166: Internal Equipment
164 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT Front Door Storage Both interior front door panels have multiple pockets for Storage storage. Glove Compartment The glove compartment is located on the passenger side of the instrument panel. To open the glove compartment, pull the release handle. Front Door Storage WARNING! If containers of hot liquid are placed in the bottle...
Page 167 GETTING TO KNOW YOUR VEHICLE 165 Instrument Panel Drawer There is a storage drawer located in the lower center of the instrument panel. It can be released by pushing the access button above it. The drawer is actuator assisted once the access button is pushed.
Page 168 166 GETTING TO KNOW YOUR VEHICLE Front Seatback Storage — If Equipped The front seatbacks have a storage pocket on some models. Drawer Fully Open CAUTION! Front Seatback Storage The storage drawer must be closed while driving. If left open during a collision, additional damage may occur to property or the drawer mechanism.
Page 169 GETTING TO KNOW YOUR VEHICLE 167 Umbrella Holder Second Row Floor Storage Bins An umbrella holder has been conveniently molded into the The area below the load floor, located in front of the second front door entry scuff moldings. row seats, is available for storage. Umbrella Holder In Floor Storage Location...
Page 170 168 GETTING TO KNOW YOUR VEHICLE 1. To access the storage bin with front seats in the rearward position, place the lock rod in the unlocked position so the load floor can fold upwards towards the seatback. Floor Latch WARNING! Lock Rod In a collision, serious injury could result if the seat storage bin covers are not properly latched.
Page 171 GETTING TO KNOW YOUR VEHICLE 169 CAUTION! WARNING! (Continued) • Do not drive the vehicle with the storage bin covers The storage bin cover must lay flat and be locked to open. Keep the storage bin covers closed and latched avoid damage from contact with the front seat tracks, while the vehicle is in motion.
Page 172 170 GETTING TO KNOW YOUR VEHICLE Seat Storage Bin Cover Emergency Release Lever Coat Hooks — If Equipped As a security measure, the Seat Storage Bin Cover has an Coat hooks are located along the headliner for the second Emergency Release Lever built into the latching mecha- and third row seating positions.
Page 173: Sun Screens - If Equipped
GETTING TO KNOW YOUR VEHICLE 171 Sun Screens — If Equipped Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks Sun screens are available for second and third row seating attached to the top of the window.
Page 174: Power Outlets
172 GETTING TO KNOW YOUR VEHICLE Power Outlets The front power outlet is located at the bottom of the instrument panel. Your vehicle is equipped with 12 Volt (15 Amp) power outlets, and 5 Volt (2.5 Amp) USB power outlets, that can be used to power cellular phones, small electronics and other low powered electrical accessories.
Page 175 GETTING TO KNOW YOUR VEHICLE 173 Front USB Charge Only Port Rear Power Outlet In addition to the front power outlets, there is also a power NOTE: The USB outlet in the bottom of the instrument outlet located in the rear cargo area. panel can be switched from “ignition”...
Page 176 174 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 177: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE 175 Power Inverter — If Equipped The Power Inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the There is a 115 Volt, 150 Watt Power Inverter outlet located Power Inverter shuts down.
Page 178: Smoker's Package Kit - If Equipped
176 GETTING TO KNOW YOUR VEHICLE Overhead Sunglass Storage WARNING! At the front of the overhead console, a compartment is When the cigar lighter is in use it becomes very hot. To provided for the storage of one pair of sunglasses. avoid serious injury, handle the cigar lighter with care.
Page 179: Roof Luggage Rack - If Equipped
GETTING TO KNOW YOUR VEHICLE 177 The door will slowly rotate to the full open position. Roof Rack Full Open Position 1 — Side Rail ROOF LUGGAGE RACK — IF EQUIPPED 2 — Crossbar The crossbars and side rails are designed to carry weight The roof rack does not increase the total load carrying on vehicles equipped with a luggage rack.
Page 180: Deploying The Crossbars
178 GETTING TO KNOW YOUR VEHICLE Deploying The Crossbars 1. To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar from its stowed position in the side rail. Repeat with crossbar on the opposite side. Removing Crossbars CAUTION! Use care when removing and handling the crossbars to...
Page 181 GETTING TO KNOW YOUR VEHICLE 179 2. Bend the crossbar supports at each end, taking care to 3. Position the crossbars across the roof making sure the keep hand clear of pivoting joint. Slide the thumb screw letters on the crossbars align with the matching letters down.
Page 182: Stowing The Crossbars
180 GETTING TO KNOW YOUR VEHICLE 4. Once the crossbar is in place, tighten both thumb screws Stowing The Crossbars completely. 1. Starting with one crossbar, completely loosen the thumb screws at both ends. Lift the crossbar away from the matching letter to remove it from the deployed position.
Page 183 GETTING TO KNOW YOUR VEHICLE 181 Crossbar Pivot Stowing Crossbars 3. Then, position the crossbar along the correct side rail. Make sure the letters on the crossbar align with the matching letters on the side rail.
Page 184 182 GETTING TO KNOW YOUR VEHICLE 4. The crossbar will nest fully within the side rail. 5. Once the driver’s side crossbar is in place, tighten the thumb screws completely. Crossbar To Side Rail Tightening Crossbar...
Page 185 GETTING TO KNOW YOUR VEHICLE 183 6. Repeat the procedure to stow the second crossbar on the WARNING! opposite side. Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the ve- hicle, particularly at high speeds, resulting in personal injury or property damage.
Page 186 184 GETTING TO KNOW YOUR VEHICLE CAUTION! (Continued) points if needed. Tie loops are intended as supple- mentary tie down points only. Do not use ratcheting mechanisms with the tie loops. Check the straps and thumb wheels frequently to be sure that the load remains securely attached.
Page 187 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....186 WARNING LIGHTS AND MESSAGES ..201 ▫...
Page 188: Instrument Cluster
186 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Base Instrument Cluster...
Page 189: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 187 Premium Instrument Cluster 2. Instrument Cluster Display Instrument Cluster Descriptions • When the appropriate conditions exist, this display 1. Tachometer shows the instrument cluster display messages. Refer • Indicates the engine speed in revolutions per minute to “Instrument Cluster Display”...
Page 190: Instrument Cluster Display
188 GETTING TO KNOW YOUR INSTRUMENT PANEL 3. Speedometer WARNING! (Continued) • Indicates vehicle speed. into the normal range and is no longer red. If the gauge 4. Fuel Gauge remains on the “H”, turn the engine off immediately • The gauge shows the level of fuel in the fuel tank when and call an authorized dealer for service.
Page 191: Instrument Cluster Display Location And Controls
GETTING TO KNOW YOUR INSTRUMENT PANEL 189 cluster display is designed to display important informa- The instrument cluster display controls allows the driver to tion about your vehicle’s systems and features. Using a select information by pushing the directional buttons mounted on the steering wheel: driver interactive display located on the instrument panel, your instrument cluster display can show you how sys-...
Page 192 190 GETTING TO KNOW YOUR INSTRUMENT PANEL • Right Arrow Button Vehicle Info • Tire Pressure Monitor Push and release the right arrow button to access the information screens or submenu screens of a • Coolant Temp main menu item. •...
Page 193: Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL 191 Trip (Trip A/Trip B) is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal • Distance driving style. • Average MPG • Unless reset, this message will continue to display each •...
Page 194: Keysense Cluster Messages - If Equipped
192 GETTING TO KNOW YOUR INSTRUMENT PANEL Without pressing the brake pedal, push the ENGINE KeySense Cluster Messages — If Equipped START/STOP button and place the ignition in the ON/ When the KeySense key is in use there will be: RUN position (do not start the vehicle.) •...
Page 195: Instrument Cluster Display Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL 193 Setting Instrument Cluster Display Message ParkSense “Feature cannot be disabled. KeySense in use” Blind Spot “Feature cannot be disabled. KeySense in use” Forward Collision Warning “Feature cannot be disabled. KeySense in use” • Tire Pressure Instrument Cluster Display Menu Items •...
Page 196 194 GETTING TO KNOW YOUR INSTRUMENT PANEL • Transmission Temperature If the conditions are met, holding the OK button will reset the gauge and the numeric display will return to 100%. Displays the actual transmission temperature. If the conditions are not met, a popup message will display •...
Page 197 GETTING TO KNOW YOUR INSTRUMENT PANEL 195 – Current Fuel Economy (MPG, L/100 km, or km/l) Audio – The Max and Min values will correspond to the Push and release the up or down arrow button until the particular engine requirements Audio Menu displays in the instrument cluster display.
Page 198 196 GETTING TO KNOW YOUR INSTRUMENT PANEL Screen Setup submenus. The Screen Setup feature allows you to change what information is displayed in the instrument cluster as Push and release the up or down arrow button until the well as the location that information is displayed. Screen Setup Menu displays in the instrument cluster display.
Page 199 GETTING TO KNOW YOUR INSTRUMENT PANEL 197 Premium Instrument Cluster Display Screen Setup Options: • None 3 — Lower Right • Compass • Outside Temp. (Default) • Time • Range • Average/Current (MPG, L/100km, or km/L) • Trip A Distance •...
Page 200 198 GETTING TO KNOW YOUR INSTRUMENT PANEL Base Instrument Cluster Display Screen Setup Options: • None 2 — Upper Right • Compass • Outside Temp (Default) • Time • Range • Average/Current (MPG, L/100km, or km/L) • None 3 — Center •...
Page 201: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL 199 Battery Saver On/Battery Saver Mode Message — NOTE: Electrical Load Reduction Actions — If Equipped • The charging system is independent from load reduc- tion. The charging system performs a diagnostic on the This vehicle is equipped with an Intelligent Battery Sensor charging system continuously.
Page 202 200 GETTING TO KNOW YOUR INSTRUMENT PANEL • The battery was used for an extended period with the Loss of the battery charge may indicate one or more of the following conditions: engine not running to supply radio, lights, chargers, +12V portable appliances like vacuum cleaner’s, game •...
Page 203: Trip Computer
GETTING TO KNOW YOUR INSTRUMENT PANEL 201 • The vehicle should have service performed if the mes- Trip B sage is still present during consecutive trips and the • Shows the total distance traveled for Trip B since the last evaluation of the vehicle and driving pattern did not reset.
Page 204: Red Warning Lights
202 GETTING TO KNOW YOUR INSTRUMENT PANEL Red Warning Lights been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, — Air Bag Warning Light and a brake pedal pulsation may be felt during each stop. This light indicates a fault with the air bag, and will turn on The dual brake system provides a reserve braking capacity for four to eight seconds as a bulb check when the ignition...
Page 205 GETTING TO KNOW YOUR INSTRUMENT PANEL 203 Vehicles equipped with the Anti-Lock Brake System (ABS) — Door Open Warning Light — If Equipped are also equipped with Electronic Brake Force Distribution This indicator will illuminate when a door is ajar/open and (EBD).
Page 206 204 GETTING TO KNOW YOUR INSTRUMENT PANEL and the transmission is placed in the PARK position. The If the light turns on while driving, safely pull over and stop light should turn off. If the light remains on with the the vehicle.
Page 207 GETTING TO KNOW YOUR INSTRUMENT PANEL 205 — Transmission Temperature Warning Light — If — Vehicle Security Warning Light — If Equipped Equipped This light will flash at a fast rate for approximately 15 This light indicates high transmission fluid temperature. seconds when the vehicle security alarm is arming, and This may occur with strenuous usage such as trailer then will flash slowly until the vehicle is disarmed.
Page 208: Yellow Warning Lights
206 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Warning Lights — Electronic Park Brake Warning Light This telltale will turn on to indicate the Electronic Park — Adaptive Cruise Control (ACC) Fault Warning Brake is not functioning properly and service is required. Light —...
Page 209 GETTING TO KNOW YOUR INSTRUMENT PANEL 207 (kilometers) at speeds greater than 30 mph (48 km/h), see — Low Fuel Warning Light your authorized dealer as soon as possible to have the When the fuel level reaches approximately 1.85 gal (7 L) problem diagnosed and corrected.
Page 210 208 GETTING TO KNOW YOUR INSTRUMENT PANEL several typical driving styles. In most situations, the ve- — Service Forward Collision Warning (FCW) hicle will drive normally and will not require towing. Light — If Equipped This telltale will turn on to indicate a fault in the Forward When the engine is running, the MIL may flash to alert Collision Warning System.
Page 211 GETTING TO KNOW YOUR INSTRUMENT PANEL 209 can lead to tire failure. Under-inflation also reduces fuel CAUTION! efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Do not continue driving with one or more flat tires as handling may be compromised.
Page 212: Yellow Indicator Lights
210 GETTING TO KNOW YOUR INSTRUMENT PANEL ensure that the replacement or alternate tires and wheels — Rear Fog Light Indicator allow the TPMS to continue to function properly. This indicator will illuminate when the rear fog lights are CAUTION! Green Indicator Lights The TPMS has been optimized for the original equip- —...
Page 213: Blue Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 211 — Front Fog Indicator Light — If Equipped — Stop/Start Active Indicator Light — If Equipped This indicator will illuminate when the front fog lights are This telltale will illuminate when the Stop/Start function is in “Autostop”...
Page 214: White Indicator Lights
212 GETTING TO KNOW YOUR INSTRUMENT PANEL the rear of the vehicle) to turn off the high beams. If the Refer to “LaneSense — If Equipped in “Starting And high beams are off, pull the lever toward you for a Operating”...
Page 215: Onboard Diagnostic System - Obd Ii
GETTING TO KNOW YOUR INSTRUMENT PANEL 213 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! (Continued) Your vehicle is equipped with a sophisticated Onboard • If the MIL is flashing while the vehicle is running, Diagnostic system called OBD II. This system monitors the severe catalytic converter damage and power loss performance of the emissions, engine, and automatic trans- will soon occur.
Page 216: Emissions Inspection And Maintenance Programs
214 GETTING TO KNOW YOUR INSTRUMENT PANEL Normally, the OBD II system will be ready. The OBD II WARNING! (Continued) system may not be ready if your vehicle was recently vehicle control could occur that may result in an serviced, recently had a dead battery or a battery replace- accident involving serious injury or death.
Page 217 GETTING TO KNOW YOUR INSTRUMENT PANEL 215 3. Approximately 15 seconds later, one of two things will If your OBD II system is not ready, you should see an happen: authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, •...
Page 219 SAFETY CONTENTS ▫ Seat Belt Systems ..... .245 SAFETY FEATURES ..... .218 ▫...
Page 220: Safety Features
218 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 221: Electronic Brake Control System
SAFETY benefits of anti-lock brakes. If the “Anti-Lock Brake Warn- WARNING! (Continued) ing Light” does not come on when the ignition is turned to • The capabilities of an ABS equipped vehicle must the ON/RUN mode, have the light repaired as soon as never be exploited in a reckless or dangerous manner possible.
Page 222 220 SAFETY and controls the wheel spin across a driven axle. If one WARNING! wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This The Brake Assist System (BAS) cannot prevent the will allow more vehicle torque to be applied to the wheel natural laws of physics from acting on the vehicle, nor that is not spinning.
Page 223 SAFETY Dynamic Steering Torque (DST) Electronic Roll Mitigation (ERM) Dynamic Steering Torque is a feature of the ESC and This system anticipates the potential for wheel lift by Electric Power Steering (EPS) modules that provides monitoring the driver’s steering wheel input and the speed torque at the steering wheel for certain driving conditions of the vehicle.
Page 224 222 SAFETY Electronic Stability Control (ESC) Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to This system enhances directional control and stability of adapt your speed and driving to the prevailing road the vehicle under various driving conditions.
Page 225 SAFETY Partial Off WARNING! (Continued) The “Partial Off” mode is intended for times when a more the performance of the ESC system. Changes to the spirited driving experience is desired. This mode may steering system, suspension, braking system, tire modify TCS and ESC thresholds for activation, which type and size or wheel size may adversely affect ESC allows for more wheel spin than normally allowed.
Page 226 224 SAFETY The “ESC Activation/Malfunction Indicator Light” (lo- WARNING! (Continued) cated in the instrument cluster) starts to flash as soon as the in the TCS section), has been disabled and the “ESC tires lose traction and the ESC system becomes active. The Off Indicator Light”...
Page 227 SAFETY • HSA will work in REVERSE gear and all forward gears. Hill Start Assist (HSA) The system will not activate if the transmission is in The HSA system is designed to mitigate roll back from a PARK or NEUTRAL. For vehicles equipped with a complete stop while on an incline.
Page 228 226 SAFETY Towing With HSA Disabling And Enabling HSA HSA will also provide assistance to mitigate roll back while This feature can be turned on or turned off. To change the towing a trailer. current setting, proceed as follows: • If disabling HSA using Uconnect Settings, refer to WARNING! “Uconnect Settings”...
Page 229: Auxiliary Driving Systems
SAFETY Trailer Sway Control (TSC) AUXILIARY DRIVING SYSTEMS TSC uses sensors in the vehicle to recognize an excessively Blind Spot Monitoring (BSM) — If Equipped swaying trailer and will take the appropriate actions to The Blind Spot Monitoring (BSM) system uses two radar- attempt to stop the sway.
Page 230 228 SAFETY • The Blind Spot Monitoring (BSM) system may experi- BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when ence drop outs (blinking on and off) of the side mirror the vehicle is in PARK.
Page 231 SAFETY If the system detects degraded performance due to con- tamination or foreign objects, a message will warn you of a blocked sensor and the warning indicators in side view mirrors will be on. The warning indicators will remain illuminated until blockage clearing conditions are met. First clear the fascia area around the sensors of the block- age.
Page 232 230 SAFETY Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 233 SAFETY Overtaking Traffic If you pass another vehicle slowly with a relative speed less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
Page 234 232 SAFETY the system may alert on such objects. This is normal operation and your vehicle does not require service. Opposing Traffic WARNING! Stationary Objects The Blind Spot Monitoring system is only an aid to The BSM system will not alert you of objects that are help detect objects in the blind spot zones.
Page 235 SAFETY Rear Cross Path (RCP) (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their NOTE: In a parking lot situation, oncoming vehicles can be vision of oncoming vehicles may be blocked.
Page 236 234 SAFETY Modes Of Operation NOTE: Whenever an audible alert is requested by the BSM system, the radio is also muted. Three selectable modes of operation are available in the Uconnect System. Refer to “Uconnect Settings” in “Multi- When the system is in RCP, the system shall respond with media”...
Page 237: Forward Collision Warning (Fcw) With Mitigation - If Equipped
SAFETY General Information NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller The following regulatory statement applies to all Radio (EBC), to calculate the probability of a forward collision. Frequency (RF) devices equipped in this vehicle: When the system determines that a forward collision is This device complies with Part 15 of the FCC Rules and probable, the driver will be provided with audible and...
Page 238 236 SAFETY • It is unsafe to test the FCW system. To prevent such misuse of the system, after four Active Braking events within a key cycle, the Active Braking portion of FCW will be deactivated until the next key cycle. •...
Page 239 SAFETY FCW Braking Status And Sensitivity NOTE: • Changing the FCW status to “Only Warning” prevents The FCW Sensitivity and Active Braking status are pro- the system from providing limited active braking, or grammable through the Uconnect System. Refer to additional brake support if the driver is not braking “Uconnect Settings”...
Page 240: Tire Pressure Monitor System (Tpms)
238 SAFETY FCW Limited Warning General Information If the instrument cluster displays “ACC/FCW Limited The following regulatory statement applies to all Radio Functionality” or “ACC/FCW Limited Functionality Clean Frequency (RF) devices equipped in this vehicle: Front Windshield” momentarily, there may be a condition This device complies with Part 15 of the FCC Rules and that limits FCW functionality.
Page 241 SAFETY three hours, or driven less than 1 mile (1.6 km) after a three be driven for up to 20 minutes above 15 mph (24 km/h) in hour period. The cold tire inflation pressure must not order for the TPMS to receive this information. exceed the maximum inflation pressure molded into the For example, your vehicle may have a recommended cold tire sidewall.
Page 242 240 SAFETY NOTE: CAUTION! • The TPMS is not intended to replace normal tire care and • The TPMS has been optimized for the original maintenance, or to provide warning of a tire failure or equipment tires and wheels. TPMS pressures and condition.
Page 243 SAFETY monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
Page 244 242 SAFETY • Using tire chains on the vehicle. Service TPMS Warning • Using wheels/tires not equipped with TPMS sensors. When a system fault is detected, the “Tire Pressure Moni- toring Telltale Light” will flash on and off for 75 seconds Vehicles With Compact Spare —...
Page 245 SAFETY cluster will display a “SERVICE TPM SYSTEM” mes- display the “SERVICE TPM SYSTEM” message and then sage for five seconds and then display dashes (- -) in display dashes (--) in place of the pressure values. place of the pressure value. Beginning with the next ignition cycle, the TPMS will no 5.
Page 246: Occupant Restraint Systems
244 SAFETY (2) This device must accept any interference received, Here are some simple steps you can take to minimize the including interference that may cause undesired operation. risk of harm from a deploying air bag: NOTE: Changes or modifications not expressly approved 1.
Page 247: Seat Belt Systems
SAFETY 6. All occupants should always wear their lap and shoul- Seat Belt Systems der belts properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and 7.
Page 248 246 SAFETY a few seconds. If the driver or outboard front seat passen- Change of Status ger (if equipped with outboard front passenger seat If the driver or outboard front seat passenger (if equipped BeltAlert) is unbuckled when the ignition switch is first in with outboard front passenger seat BeltAlert) unbuckles the START or ON/RUN position the Seat Belt Reminder their seat belt while the vehicle is traveling, the BeltAlert...
Page 249 SAFETY Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • It is dangerous to ride in a cargo area, inside or lap/shoulder belts. outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or The seat belt webbing retractor will lock only during very killed.
Page 250 248 SAFETY WARNING! WARNING! (Continued) vehicle in a collision, increasing head and neck • A lap belt worn too high can increase the risk of injury. A seat belt worn under the arm can cause injury in a collision. The seat belt forces won’t be at internal injuries.
Page 251 SAFETY equipped with a rear seat). Grasp the latch plate and 3. When the seat belt is long enough to fit, insert the latch pull out the seat belt. Slide the latch plate up the plate into the buckle until you hear a “click.” webbing as far as necessary to allow the seat belt to go around your lap.
Page 252 250 SAFETY on the lap belt. A snug seat belt reduces the risk of Lap/Shoulder Belt Untwisting Procedure sliding under the seat belt in a collision. Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
Page 253 SAFETY NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.
Page 254 252 SAFETY Second Row Center (If Equipped) And Third Row Center Seat Belt Operating Instructions The second row center (if equipped) and third row center seat belts feature a seat belt with a mini-latch plate and buckle, which allows the seat belt to detach from the lower anchor when the seat is folded.
Page 255 SAFETY 2. Grasp the mini-latch plate and pull the seat belt over the 3. Route the shoulder belt to the inside of the left head seat. restraint. Mini-Latch Plate Routing The Rear Seat Belt Latch Plate 1 — Seat Belt Latch Plate...
Page 256 254 SAFETY 4. When the seat belt is long enough to fit, insert the 5. Sit back in seat. Slide the regular latch plate up the mini-latch plate into the mini-buckle until you hear a webbing as far as necessary to allow the seat belt to go “click.”...
Page 257 SAFETY 6. When the seat belt is long enough to fit, insert the latch 9. To release the seat belt, push the red button on the plate into the buckle until you hear a “click.” buckle. 10. To disengage the mini-latch plate from the mini-buckle for storage, insert the regular latch plate into the center red slot on the mini-buckle.
Page 258 256 SAFETY Seat Belt Extender Seat Belts And Pregnant Women If a seat belt is not long enough to fit properly, even when the webbing is fully extended and the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a Seat Belt Extender.
Page 259 SAFETY Seat Belt Pretensioner Switchable Automatic Locking Retractors (ALR) The front seat belt system is equipped with pretensioning The seat belts in the passenger seating positions are devices that are designed to remove slack from the seat belt equipped with a Switchable Automatic Locking Retractor in the event of a collision.
Page 260 258 SAFETY 7 Passenger Stow ‘n Go Seating Automatic Locking 8 Passenger Automatic Locking Retractor (ALR) Locations Retractor (ALR) Locations ALR — Switchable Automatic Locking Retractor ALR — Switchable Automatic Locking Retractor If the passenger seating position is equipped with an ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR.
Page 261 SAFETY In Automatic Locking Mode, the shoulder belt is automati- 3. Allow the seat belt to retract. As the seat belt retracts, cally pre-locked. The seat belt will still retract to remove you will hear a clicking sound. This indicates the seat any slack in the shoulder belt.
Page 262 260 SAFETY Seat Belt Park Stitch — If Equipped Third Row Stow Clip - If Equipped The rear outboard seat belts may be equipped with a park Your vehicle may be equipped with a stow clip on the stitch to raise the latch plate for easier access to occupants. lower trim behind the third row.
Page 263: Supplemental Restraint Systems (Srs)
SAFETY • Instrument Panel WARNING! • Knee Impact Bolsters Do not place the seat belt webbing behind the third • Driver and Front Passenger Air Bags row stow clip when using the seat belt to restrain an occupant. The seat belt will not be positioned properly •...
Page 264 262 SAFETY The ORC turns on the Air Bag Warning Light in the NOTE: If the speedometer, tachometer, or any engine instrument panel for approximately four to eight seconds related gauges are not working, the Occupant Restraint for a self-check when the ignition switch is first in the Controller (ORC) may also be disabled.
Page 265 SAFETY Light has come on and a fault has been detected. If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately. For additional information regarding the Redundant Air Bag Warning Light refer to “Getting To Know Your Instrument Panel”...
Page 266 264 SAFETY This vehicle may be equipped with a driver and/or front WARNING! (Continued) passenger seat belt buckle switch that detects whether the to inflate. Sit back, comfortably extending your arms driver or front passenger seat belt is buckled. The seat belt to reach the steering wheel or instrument panel.
Page 267 SAFETY On the other hand, depending on the type and location of WARNING! (Continued) impact, front air bags may deploy in crashes with little • Do not put anything on or around the air bag covers vehicle front-end damage but that produce a severe initial or attempt to open them manually.
Page 268 266 SAFETY Occupant Classification System (OCS) — Front probable classification. The OCM communicates this infor- Passenger Seat mation to the ORC. The ORC may reduce the inflation rate of the Passenger Advanced Front Air Bag deployment The OCS is part of a Federally regulated safety system for based on occupant classification.
Page 269 SAFETY Front Passenger Seat Front Passenger Air Bag WARNING! Occupant Status Output • Never place a rear-facing child restraint in front of an Rear-facing child restraint Reduced-power deploy- air bag. A deploying passenger front air bag can ment cause death or serious injury to a child 12 years or Child, including a child in Reduced-power deploy- younger, including a child in a rear-facing child...
Page 270 268 SAFETY • Sitting in the center of the seat with their feet comfort- Do not decrease OR increase the front passenger’s seated ably on or near the floor weight on the front passenger seat • Sitting with their back against the seatback and the The front passenger’s seated weight must be properly positioned on the front passenger seat.
Page 271 SAFETY • The front passenger carries or holds an object while seated (e.g., backpack, box, etc.). • Objects are lodged under the front passenger seat. • Objects are lodged between the front passenger seat and center console. • Accessories that may change the seated weight on the front passenger seat are attached to the front passenger seat.
Page 272 270 SAFETY Not Seated Properly Not Seated Properly...
Page 273 SAFETY WARNING! (Continued) the seatback, sitting upright, facing forward, in the center of the seat, with your feet comfortably on or near the floor. • Do not carry or hold any objects (e.g., backpacks, boxes, etc.) while seated in the front passenger seat. Holding an object may provide an output signal to the OCS that is different than the occupant’s prop- erly seated weight input, which may result in serious...
Page 274 272 SAFETY The passenger seat assembly contains critical OCS compo- be modified or replaced with any part except those nents that may affect the Passenger Advanced Front Air which are approved by FCA US LLC. Bag inflation. In order for the OCS to properly classify the seated weight of a front seat passenger, the OCS compo- WARNING! nents must function as designed.
Page 275 SAFETY Supplemental Seat-Mounted Side Air Bags (SABs) are WARNING! located in the outboard side of the front seats. The SABs are • Do not drill, cut, or tamper with the knee impact marked with “SRS AIRBAG” or “AIRBAG” on a label or on the seat trim on the outboard side of the seats.
Page 276 274 SAFETY through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 277 SAFETY positioned in the area where the SABICs inflate. Children Side Impacts are at an even greater risk of injury from a deploying air The Side Air Bags are designed to activate in certain side bag. impacts. The Occupant Restraint Controller (ORC) deter- The SABICs may help reduce the risk of partial or complete mines whether the deployment of the Side Air Bags in a ejection of vehicle occupants through side windows in...
Page 278 276 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! system. Side Air Bags deploy in less time than it takes to • Side Air Bags need room to inflate. Do not lean blink your eyes. against the door or window.
Page 279 SAFETY • Supplemental Side Air Bags The Side Air Bags will not deploy in all rollover events. The rollover sensing system determines if a rollover event may • Supplemental Knee Air Bags be in progress and whether deployment is appropriate. In •...
Page 280 278 SAFETY quickly. However, if you haven’t healed significantly NOTE: within a few days, or if you have any blistering, see your • Air bag covers may not be obvious in the interior trim, doctor immediately. but they will open during air bag deployment. •...
Page 281 SAFETY Your vehicle may also be designed to perform any of these NOTE: After an accident, remember to cycle the ignition to other functions in response to the Enhanced Accident the STOP (OFF/LOCK) position and remove the key from Response System: the ignition switch to avoid draining the battery.
Page 282 280 SAFETY Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
Page 283: Child Restraints
SAFETY NOTE: EDR data are recorded by your vehicle only if a Children 12 years or younger should ride properly buckled non-trivial crash situation occurs; no data are recorded by up in a rear seat, if available. According to crash statistics, the EDR under normal driving conditions and no personal children are safer when properly restrained in the rear data (e.g., name, gender, age, and crash location) are...
Page 284 282 SAFETY Before buying any restraint system, make sure that it has a NOTE: label certifying that it meets all applicable Safety Stan- • For additional information, refer to www.safercar.gov/ dards. You should also make sure that you can install it in parents/index.htm or call: 1–888–327–4236 the vehicle where you will use it.
Page 285 SAFETY Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Children Too Large for Child Children 12 years old or younger, Vehicle Seat Belt, seated in the rear Restraints who have outgrown the height or seat of the vehicle weight limit of their booster seat Infant And Child Restraints WARNING!
Page 286 284 SAFETY in a forward-facing child seat with a harness for as long as WARNING! (Continued) possible, up to the highest weight or height allowed by the was designed by the car seat manufacturer, and your child seat. child may be more severely injured as a result. All children whose weight or height is above the forward- facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
Page 287 SAFETY 3. Does the shoulder belt cross the child’s shoulder be- WARNING! (Continued) tween their neck and arm? Remove the child restraint before adjusting the ve- 4. Is the lap part of the belt as low as possible, touching the hicle seat position.
Page 288 286 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Use Any Attachment Method Shown With An “X” Below Weight of the LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Child + Child Anchors Only Anchors + Top Tether Anchor Restraint...
Page 289 SAFETY Lower Anchors And Tethers For CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage Restraint System system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.
Page 290 288 SAFETY LATCH Positions For Installing Child Restraints In This Vehicle 7 Passenger Stow ‘n Go Seating LATCH Positions Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol 7 Passenger Bench Seat LATCH Positions Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol...
Page 291 SAFETY 8 Passenger LATCH Positions Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH anchor-...
Page 292 290 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the LATCH anchorages and the Do not use the seat belt when you seat belt be used together to attach a use the LATCH anchorage system to rear-facing or forward-facing child attach a rear-facing or forward-facing restraint? child restraint.
Page 293 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the head restraints be removed? The 2nd row head restraints on bench and the center head restraint in the 8 passenger vehicle are remov- able. 2nd row Stow ’n Go head re- straints are not removable.
Page 294 292 SAFETY Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 295 SAFETY LATCH Anchorages LATCH Anchorages (Second Row Bench Anchorages Shown) (Third Row 60/40 Anchorages Shown) Locating The Upper Tether Anchorages There are tether strap anchorages located behind all second row seating positions. The third row has a tether anchor on the 40% seat for the right outboard position and in the center of the 60%...
Page 296 294 SAFETY seat for either the center or left outboard seating position. All tether anchorages are located on the back of the seat, near the floor. Tether Strap Anchorages (Second Row 8 Passenger Anchorage Shown) Tether Strap Anchorages (Second Row Bench Anchorage Shown)
Page 297 SAFETY Center Seat LATCH This vehicle has 4 lower LATCH anchorages in the third row, rear seat. Anchorages A and B are used for the right outboard position behind the front passenger (1). Anchor- ages C and D are used for the center seating position (2). The left outboard position (3) does not have lower anchor- ages.
Page 298 296 SAFETY not use that outboard position. If a child seat in the center 1. Loosen the adjusters on the lower straps and on the position blocks the outboard LATCH anchors or seat belt, tether strap of the child seat so that you can more easily do not install a child seat in that outboard position.
Page 299 SAFETY 6. Test that the child restraint is installed tightly by pulling WARNING! back and forth on the child seat at the belt path. It • Improper installation of a child restraint to the should not move more than 1 inch (25.4 mm) in any direction.
Page 300 298 SAFETY Lap/Shoulder Belt Systems For Installing Child WARNING! (Continued) Restraints In This Vehicle • Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 301 SAFETY 7 Passenger Stow ‘n Go Seating Automatic Locking 8 Passenger Automatic Locking Retractor (ALR) Locations Retractor (ALR) Locations ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Frequently Asked Questions What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when...
Page 302 300 SAFETY Frequently Asked Questions Can the rear-facing child restraint Contact between the front passenger touch the back of the front passenger seat and the child restraint is al- seat? lowed, if the child restraint manufac- turer also allows contact. Can the head restraints be removed? The 2nd row head restraints on bench and the center head restraint...
Page 303 SAFETY Installing A Child Restraint With A Switchable WARNING! (Continued) Automatic Locking Retractor (ALR): head restraint in its lowered position could result in Child restraint systems are designed to be secured in serious injury or death in a collision. vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt.
Page 304 302 SAFETY 3. Slide the latch plate into the buckle until you hear a 8. If the child restraint has a top tether strap and the “click.” seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether 4.
Page 305 SAFETY Seat Belt Park Stitch Location Seat Belt Park Stitch If the park stitch interferes with the lock-off features of the Installing Child Restraints Using the Top Tether child restraint, do not use the lock-off feature. Instead, Anchorage switch the seat belt to the locking mode, as described in the steps above or move the car seat to a different seating WARNING! position.
Page 306 304 SAFETY WARNING! (Continued) “Lower Anchors and Tethers for CHildren (LATCH) Restraint System” for the location of approved tether anchorages in your vehicle. Top Tether Anchorage Locations 2nd Row Bench 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage.
Page 307 SAFETY Top Tether Anchorage Locations 2nd Row 8 Passenger Top Tether Anchorage Locations 3rd Row 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
Page 308 306 SAFETY 4. Remove slack in the tether strap according to the child WARNING! (Continued) restraint manufacturer’s instructions. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
Page 309 SAFETY 3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Outboard Tether Attachments – 3rd Row WARNING! Do not connect the tether strap for more than one child restraint to the tether anchorage on the 60% seat in the...
Page 310: Transporting Pets
308 SAFETY Transporting Pets WARNING! (Continued) Air Bags deploying in the front seat could harm your pet. • Do not allow people to ride in any area of your An unrestrained pet will be thrown about and possibly vehicle that is not equipped with seats and seat belts. injured, or injure a passenger during panic braking or in a •...
Page 311: Safety Checks You Should Make Inside The Vehicle
SAFETY Safety Checks You Should Make Inside The Vehicle WARNING! (Continued) Seat Belts • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling con- Inspect the seat belt system periodically, checking for cuts, trols to force outside air into the vehicle.
Page 312 310 SAFETY Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place the upside down or turn your floor mat over. Lightly pull blower control on high speed. You should be able to feel the to confirm mat is secured using the floor mat fasten- air directed against the windshield.
Page 313: Periodic Safety Checks You Should Make Outside
SAFETY Periodic Safety Checks You Should Make Outside WARNING! (Continued) The Vehicle • ONLY use the passenger’s side floor mat on the Tires passenger’s side floor area. • ALWAYS make sure objects cannot fall or slide into Examine tires for excessive tread wear and uneven wear the driver’s side floor area when the vehicle is patterns.
Page 315 STARTING AND OPERATING CONTENTS ▫ Nine-Speed Automatic Transmission ..327 STARTING THE ENGINE ....317 ▫ Normal Starting ..... . .317 ▫...
Page 316 314 STARTING AND OPERATING ▫ To Set A Desired Speed....339 ▫ ACC Operation At Stop ....351 ▫...
Page 317 STARTING AND OPERATING 315 ▫ ParkSense Visual Alert ....373 ▫ Changing LaneSense Status ....409 ▫...
Page 318 316 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND DRIVING TIPS ......431 MOTORHOME, ETC.) ....430 ▫...
Page 319: Starting The Engine
STARTING AND OPERATING 317 STARTING THE ENGINE Start the engine with the gear selector in the NEUTRAL or PARK position. Apply the brake before shifting to any Before starting your vehicle, adjust your seat, adjust both driving range. inside and outside mirrors, and fasten your seat belts. Normal Starting WARNING! NOTE: Normal starting of either a cold or a warm engine...
Page 320: Cold Weather Operation (Below -22°F Or −30°C)
318 STARTING AND OPERATING ENGINE START/STOP Button Functions — With Driv- After Starting — Warming Up The Engine er’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL The idle speed is controlled automatically and it will Position) decrease as the engine warms up. The ENGINE START/STOP button operates similar to an If Engine Fails To Start ignition switch.
Page 321: To Turn Off The Engine Using Engine Start/Stop Button
STARTING AND OPERATING 319 To Turn Off The Engine Using ENGINE ENGINE BLOCK HEATER — IF EQUIPPED START/STOP Button The engine block heater warms the engine and permits quicker starts in cold weather. 1. Place the gear selector in PARK, then push and release the ENGINE START/STOP button.
Page 322: Engine Break-In Recommendations
320 STARTING AND OPERATING NOTE: While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. • The engine block heater cord is a factory installed Wide-open throttle acceleration in low gear can be detri- option.
Page 323: Park Brake
STARTING AND OPERATING 321 PARK BRAKE Electric Park Brake (EPB) Your vehicle is equipped with an Electric Park Brake System (EPB) that offers simple operation, and some additional features that make the park brake more conve- nient and useful. The park brake is primarily intended to prevent the vehicle from rolling while parked.
Page 324 322 STARTING AND OPERATING NOTE: The EPB fault lamp will illuminate if the EPB Once the park brake is fully disengaged, the BRAKE switch is held for longer than 180 seconds. The light will warning lamp in the instrument cluster and the LED extinguish upon releasing the switch.
Page 325 STARTING AND OPERATING 323 WARNING! (Continued) CAUTION! of reasons. A child or others could be seriously or If the Brake System Warning Light remains on with the fatally injured. Children should be warned not to parking brake released, a brake system malfunction is touch the parking brake, brake pedal or the trans- indicated.
Page 326 324 STARTING AND OPERATING Auto Park Brake Brake Service Mode The Electric Park Brake can be programmed to be applied We recommend having your brakes serviced by your automatically whenever the vehicle is at a standstill and authorized dealer. You should only make repairs for which the automatic transmission is placed in PARK.
Page 327: Automatic Transmission
STARTING AND OPERATING 325 When brake service work is complete, the following steps WARNING! (Continued) must be followed to reset the parking brake system to • Your vehicle could move and injure you and others if normal operation: it is not in PARK. Check by trying to move the •...
Page 328: Ignition Park Interlock
326 STARTING AND OPERATING WARNING! (Continued) CAUTION! should never exit a vehicle while the engine is Damage to the transmission may occur if the following running. Before exiting a vehicle, always come to a precautions are not observed: complete stop, then apply the parking brake, shift •...
Page 329: Brake/Transmission Shift Interlock System
STARTING AND OPERATING 327 NOTE: The transmission is NOT locked in PARK when the rotate it, to access the L position. You must also press the ignition is in the ACC mode (even though the engine will brake pedal to shift the transmission out of PARK (or be off).
Page 330: Gear Ranges
328 STARTING AND OPERATING vehicle and driveline combinations utilize 9th gear only in Gear Ranges very specific driving situations and conditions. Do not depress the accelerator pedal when shifting from Only shift from DRIVE to PARK or REVERSE when the PARK or NEUTRAL into another gear range.
Page 331 STARTING AND OPERATING 329 When exiting the vehicle, always: WARNING! (Continued) • Apply the parking brake. vehicle is completely stopped, and the PARK posi- • Shift the transmission into PARK. tion is properly indicated, before exiting the vehicle. • It is dangerous to shift out of PARK or NEUTRAL if •...
Page 332 330 STARTING AND OPERATING The following indicators should be used to ensure that you WARNING! (Continued) have properly engaged the transmission into the PARK • Never leave children alone in a vehicle, or with position: access to an unlocked vehicle. Allowing children to •...
Page 333 STARTING AND OPERATING 331 If the transmission temperature exceeds normal operating WARNING! (Continued) limits, the transmission controller may modify the trans- that limit your response to changing traffic or road mission shift schedule, reduce engine torque, and/or ex- conditions. You might lose control of the vehicle and pand the range of torque converter clutch engagement.
Page 334 332 STARTING AND OPERATING LOW (L) 3. Push and hold the ignition switch until the engine turns OFF. Use this range for engine braking when descending very steep grades. In this range, the transmission will downshift 4. Wait approximately 30 seconds. for increased engine braking.
Page 335: Active Noise Cancellation
STARTING AND OPERATING 333 NOTE: The torque converter clutch will not engage until assist or prevents the vehicle from providing assist, you the engine and/or transmission is warm (usually after 1 to will still have the ability to steer the vehicle manually. 3 miles [2 to 5 km] of driving).
Page 336: Stop/Start System - If Equipped
334 STARTING AND OPERATING assistance. Refer to “Warning Lights And Messages” in This vehicle has been upgraded with a heavy duty starter, “Getting To Know Your Instrument Panel” for further enhanced battery, and other upgraded engine parts, to information. handle the additional engine starts. NOTE: Auto Stop/Start •...
Page 337: Possible Reasons The Engine Does Not Autostop
STARTING AND OPERATING 335 • HVAC set to MAX A/C. indicating you are in Autostop. Customer settings will be maintained throughout the Auto Stop/Start process. • Engine has not reached normal operating temperature. Possible Reasons The Engine Does Not Autostop •...
Page 338: To Start The Engine While In Auto Stop/Start
336 STARTING AND OPERATING To Start The Engine While In Auto Stop/Start To Manually Turn Off The Stop/Start System While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is depressed. The transmission will automatically re-engage upon en- gine restart.
Page 339: To Manually Turn On The Stop/Start System
STARTING AND OPERATING 337 4. The STOP/START system will reset itself back to an ON NOTE: If the vehicle is left in the ACC or RUN (engine not condition every time the ignition is turned off and back running) position and the transmission is in PARK, the system will automatically time out (shut down) after an initial 30 minutes of inactivity, followed by the additional Automatic Shutdown...
Page 340: Speed Control - If Equipped
338 STARTING AND OPERATING SPEED CONTROL — IF EQUIPPED NOTE: In order to ensure proper operation, the Speed Control System has been designed to shut down if multiple When engaged, the Speed Control takes over accelerator Speed Control functions are operated at the same time. If operations at speeds greater than 25 mph (40 km/h).
Page 341: To Set A Desired Speed
STARTING AND OPERATING 339 Display” in “Getting To Know Your Instrument Panel” for WARNING! more information. The speed increment shown is depen- dent on the chosen speed unit of U.S. (mph) or Leaving the Speed Control system on when not in use Metric (km/h): is dangerous.
Page 342: To Accelerate For Passing
340 STARTING AND OPERATING • If the button is continually pushed, the set speed will To Decrease Speed continue to decrease until the button is released, then the When the Speed Control is set, you can decrease speed by new set speed will be established. pushing the SET (-) button.
Page 343: Adaptive Cruise Control (Acc) - If
STARTING AND OPERATING 341 ADAPTIVE CRUISE CONTROL (ACC) — IF The Cruise Control system has two control modes: EQUIPPED • Adaptive Cruise Control mode for maintaining an ap- propriate distance between vehicles. Adaptive Cruise Control (ACC) increases the driving con- venience provided by cruise control while traveling on •...
Page 344: Adaptive Cruise Control (Acc) Operation
342 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) You should switch off the ACC system: operation of the vehicle under all road conditions. • When driving in fog, heavy rain, heavy snow, sleet, Your complete attention is always required while driving to maintain safe control of your vehicle.
Page 345: Activating Adaptive Cruise Control (Acc)
STARTING AND OPERATING 343 Activating Adaptive Cruise Control (ACC) You can only engage ACC if the vehicle speed is above 0 mph (0 km/h). The minimum Set Speed for the ACC system is 20 mph (32 km/h). When the system is turned on and in the READY state, the instrument cluster displays “ACC Ready.”...
Page 346: To Activate/Deactivate
344 STARTING AND OPERATING To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button. The ACC menu in the instrument cluster displays “ACC Ready.” Adaptive Cruise Control Off WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally Adaptive Cruise Control Ready set the system or cause it to go faster than you want.
Page 347: To Cancel
STARTING AND OPERATING 345 • The gear selector is removed from the DRIVE position. If the system is set when the vehicle speed is below 20 mph (32 km/h), the set speed shall be defaulted to 20 mph • The Electronic Stability Control/Traction Control Sys- (32 km/h).
Page 348: To Vary The Speed Setting
346 STARTING AND OPERATING NOTE: The driver’s preferred units can be selected through the Uconnect Settings if equipped. Refer to “Uconnect Set- • If your vehicle stays at standstill for longer than two tings” in “Multimedia” for more information. The speed seconds, then the driver will either have to push the RES increment shown is dependant on the chosen speed unit of (resume) button, or apply the accelerator pedal to reen-...
Page 349 STARTING AND OPERATING 347 To Decrease Speed button is released. The decrease in set speed is reflected in the instrument cluster display. While ACC is set, the set speed can be decreased by pushing the SET (-) button. NOTE: • When you override and push the SET (+) button or SET The driver’s preferred units can be selected through the Uconnect Settings if equipped.
Page 350: Setting The Following Distance In Acc
348 STARTING AND OPERATING speed. When driving up hill and down hill, the ACC system will cancel if the braking temperature exceeds normal range (overheated). Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short).
Page 351 STARTING AND OPERATING 349 Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the Distance Setting —...
Page 352: Overtake Aid
350 STARTING AND OPERATING Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
Page 353: Acc Operation At Stop
STARTING AND OPERATING 351 ACC Operation At Stop WARNING! In the event that the ACC system brings your vehicle to a When the ACC system is resumed, the driver must standstill while following a target vehicle, if the target ensure that there are no pedestrians, vehicles or objects vehicle starts moving within two seconds of your vehicle in the path of the vehicle.
Page 354: Display Warnings And Maintenance
352 STARTING AND OPERATING Adaptive Cruise Control Ready Display Warnings And Maintenance When ACC is activated but the vehicle speed setting has “Wipe Front Radar Sensor In Front Of Vehicle” not been selected, the display will read “Adaptive Cruise Warning Control Ready.”...
Page 355 STARTING AND OPERATING 353 “Normal (Fixed Speed) Cruise Control Mode” in this When the condition that deactivated the system is no section. longer present, the system will return to the “Adaptive Cruise Control Off” state and will resume function by If weather conditions are not a factor, the driver should simply reactivating it.
Page 356: Precautions While Driving With Acc
354 STARTING AND OPERATING The “ACC/FCW Limited Functionality Clean Front Wind- Service ACC/FCW Warning shield” message can sometimes be displayed while driving If the system turns off, and the instrument cluster displays in adverse weather conditions. The ACC/FCW system will “ACC/FCW Unavailable Service Required”...
Page 357 STARTING AND OPERATING 355 Offset Driving Turns And Bends ACC may not detect a vehicle in the same lane that is offset When driving on a curve with ACC engaged, the system from your direct line of travel, or a vehicle merging in from may decrease the vehicle speed and acceleration for stabil- a side lane.
Page 358 356 STARTING AND OPERATING Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 359 STARTING AND OPERATING 357 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the ACC does not react to stationary objects and stationary lane or edging into the lane are not detected until they have vehicles.
Page 360: General Information
358 STARTING AND OPERATING General Information the ACC and the Normal (Fixed Speed) Cruise Control off. Pushing the Normal (Fixed Speed) Cruise Control on/off The following regulatory statement applies to all Radio button will result in turning on (changing to) the Normal Frequency (RF) devices equipped in this vehicle: (Fixed Speed) Cruise Control mode.
Page 361 STARTING AND OPERATING 359 turn on when the system is turned on via the on/off Metric Speed (km/h) control. It turns green when the cruise control is set. • Pushing the SET (+) button once will result in a 1 km/h increase in set speed.
Page 362: Parksense Rear Park Assist - If Equipped
360 STARTING AND OPERATING • If the button is continually pushed, the set speed will • The braking temperature exceeds normal range (over- continue to decrease in 5 mph decrements until the heated). button is released. The decrease in set speed is reflected •...
Page 363 STARTING AND OPERATING 361 • The automatic braking function can be enabled/ Automatic Transmission, the vehicle brakes may be auto- matically applied and released when performing a reverse disabled from the Customer-Programmable Features parking maneuver if the system detects a possible collision section of the Uconnect System.
Page 364: Parksense Sensors
362 STARTING AND OPERATING ParkSense can be active only when the gear selector is in REVERSE. If ParkSense is enabled at this gear selector position, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.
Page 365: Parksense Display
STARTING AND OPERATING 363 detected obstacle. Refer to “Instrument Cluster Display” in If an obstacle is detected in the left and/or right rear “Getting To Know Your Instrument Panel” for further region, the display will show a single flashing arc in the left information.
Page 366 364 STARTING AND OPERATING Slow Tone/Solid Arc Slow Tone/Solid Arc...
Page 367 STARTING AND OPERATING 365 Fast Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 368 366 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc...
Page 369 STARTING AND OPERATING 367 WARNING ALERTS Rear Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than Distance than (200- (150- (120- (100-65 cm) (65-30 cm) 12 inches (in/cm) 79 inches 150 cm) 120 cm) 100 cm) (30 cm) (200 cm) Arcs —...
Page 370: Enabling And Disabling Parksense
368 STARTING AND OPERATING Enabling And Disabling ParkSense KeySense in Use Selected Feature Cannot be Disabled message. ParkSense can be enabled and disabled with the Service The ParkSense Rear Park Assist System ParkSense switch, located on the switch panel During vehicle start up, when the ParkSense Rear Park below the Uconnect display.
Page 371: Cleaning The Parksense System
STARTING AND OPERATING 369 If “PARKSENSE UNAVAILABLE SERVICE REQUIRED” cluster display will show “PARKSENSE OFF” message appears in the instrument cluster display, see an autho- for as long as the vehicle is in REVERSE. rized dealer. • ParkSense, when on, will reduce the volume of the radio when it is sounding a tone.
Page 372: Parksense Front And Rear Park Assist - If Equipped
370 STARTING AND OPERATING WARNING! CAUTION! • Drivers must be careful when backing up even when • ParkSense is only a parking aid and it is unable to using ParkSense. Always check carefully behind recognize every obstacle, including small obstacles. your vehicle, look behind you, and be sure to check Parking curbs might be temporarily detected or not for pedestrians, animals, other vehicles, obstructions,...
Page 373 STARTING AND OPERATING 371 NOTE: The automatic braking function is intended to assist the driver in avoiding possible collisions with detected ob- • The driver can override the automatic braking function stacles when backing up in REVERSE gear. by pressing the gas pedal, turning ParkSense off via ParkSense switch, or changing the gear while the auto- NOTE: matic brakes are being applied.
Page 374: Parksense Sensors
372 STARTING AND OPERATING instrument cluster display indicating the vehicle speed is too fast. The system will become active again if the vehicle speed is decreased to speeds less than approximately 6 mph (9 km/h). ParkSense Sensors The four ParkSense sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’...
Page 375: Parksense Visual Alert
STARTING AND OPERATING 373 ParkSense Visual Alert and will produce a one-half second tone. As the vehicle moves closer to the obstacle, the display will show the The ParkSense Warning screen will only be displayed if single arc moving closer to the vehicle and the sound tone Sound and Display is selected from the Customer - Pro- will change from slow, to fast, to continuous.
Page 376 374 STARTING AND OPERATING Slow Tone/Solid Arc Slow Tone/Solid Arc...
Page 377 STARTING AND OPERATING 375 Fast Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 378 376 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc...
Page 379 STARTING AND OPERATING 377 WARNING ALERTS Rear Dis- Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than tance than (200- (150- (120- (100-65 cm) (65-30 cm) 12 inches (inches/cm) 79 inches 150 cm) 120 cm) 100 cm) (30 cm) (200 cm) Arcs —...
Page 380 378 STARTING AND OPERATING Front Park Assist If an obstacle is detected in the left and/or right front region, the display will show a single flashing arc in the left When the vehicle is in DRIVE the ParkSense Warning and/or right front region and will produce a fast sound screen will be displayed when an obstacle is detected.
Page 381 STARTING AND OPERATING 379 No Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 382 380 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc...
Page 383 STARTING AND OPERATING 381 WARNING ALERTS Front Distance Greater than 47-39 inches 39-25 inches 25-12 inches Less than (inches/cm) 47 inches (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (30 cm) (120 cm) Arcs — Left None None None 2nd Flashing 1st Flashing Arcs —...
Page 384: Enabling And Disabling Parksense
382 STARTING AND OPERATING Enabling And Disabling ParkSense KeySense in Use Selected Feature Cannot be Disabled message. ParkSense can be enabled and disabled with the Service The ParkSense Park Assist System ParkSense switch, located on the switch panel During vehicle start up, when the ParkSense System has below the Uconnect display.
Page 385: Cleaning The Parksense System
STARTING AND OPERATING 383 detected within the five second pop-up duration. The ParkSense System Usage Precautions vehicle graphic will remain displayed for as long as the NOTE: vehicle is in REVERSE. • Ensure that the front and rear bumper are free of snow, Refer to “Instrument Cluster Display”...
Page 386 384 STARTING AND OPERATING bumper, or it could provide a false indication that an WARNING! (Continued) obstacle is behind or in front of the appropriate fascia/ and blind spots before backing up. You are respon- bumper. sible for safety and must continue to pay attention to •...
Page 387: Parksense Active Park Assist System - If Equipped
STARTING AND OPERATING 385 NOTE: CAUTION! (Continued) • The driver is always responsible for controlling the sensors will not be detected when they are in close vehicle, responsible for any surrounding objects, and proximity. must intervene as required. • The vehicle must be driven slowly when using •...
Page 388: Enabling And Disabling The Parksense Active Park Assist System
386 STARTING AND OPERATING • The driver’s door is opened. Enabling And Disabling The ParkSense Active Park Assist System • The liftgate is opened. • Electronic Stability Control/Anti-lock Braking System The ParkSense Active Park Assist system can be intervention. enabled and disabled with the ParkSense Active •...
Page 389: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING 387 above approximately 18 mph (30 km/h), the system will Park Assist system will automatically search for a park- cancel. The driver must then reactivate the system by ing space on the passenger’s side of the vehicle if the pushing the ParkSense Active Park Assist switch.
Page 390 388 STARTING AND OPERATING • The feature will only indicate the last detected parking When an available parking space has been found, and the space (example: if passing multiple available parking vehicle is not in position, you will be instructed to move spaces, the system will only indicate the last detected forward to position the vehicle for a parallel parking parking space for the maneuver).
Page 391 STARTING AND OPERATING 389 Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 392 390 STARTING AND OPERATING When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete. Check Surroundings —...
Page 393 STARTING AND OPERATING 391 • The ParkSense Active Park Assist system will allow a maximum of eight shifts between DRIVE or REVERSE. If the maneuver cannot be completed within eight shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 394 392 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the DRIVE be instructed to place the gear selector into the DRIVE position, the system may instruct the driver to wait for position.
Page 395 STARTING AND OPERATING 393 The system will then instruct the driver to check their surroundings and move forward. Check Surroundings — STOP NOTE: It is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- Check Surroundings —...
Page 396 394 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 397 STARTING AND OPERATING 395 The system will then instruct the driver to check their Your vehicle is now in the parallel park position. When the surroundings and move backward. maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satis- fied with the vehicle position, they should shift to PARK.
Page 398: Perpendicular Parking Space Assistance Operation/Display
396 STARTING AND OPERATING Perpendicular Parking Space Assistance Operation/Display When the ParkSense Active Park Assist system is enabled, the “Active ParkSense Searching - Push OK for Perpen- dicular Park” message will show in the instrument cluster display. Push the OK button on the left side steering wheel switch to change your parking space setting to a perpen- dicular maneuver.
Page 399 STARTING AND OPERATING 397 • The driver is responsible to ensure that the selected When an available parking space has been found, and the parking space is suitable for the maneuver and free/ vehicle is not in position, you will be instructed to move clear of anything that may be overhanging or protruding forward to position the vehicle for a perpendicular parking into the parking space (e.g., ladders, tailgates, etc.
Page 400 398 STARTING AND OPERATING Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 401 STARTING AND OPERATING 399 When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete. Check Surroundings — Move Backwards NOTE: • It is the driver’s responsibility to use the brake and Check Surroundings —...
Page 402 400 STARTING AND OPERATING the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally. • The system will cancel the maneuver if the vehicle speed exceeds 5 mph (7 km/h) during active steering guidance into the parking space.
Page 403 STARTING AND OPERATING 401 Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the DRIVE be instructed to place the gear selector into the DRIVE position, the system may instruct the driver to wait for position.
Page 404 402 STARTING AND OPERATING The system will then instruct the driver to check their surroundings and move forward. Check Surroundings — STOP NOTE: It is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- Check Surroundings —...
Page 405 STARTING AND OPERATING 403 Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 406 404 STARTING AND OPERATING The system will then instruct the driver to check their shift to PARK. The Active ParkSense Complete - Check surroundings and move backward. Parking Position message will be momentarily displayed. Check Surroundings — Move Backwards Active ParkSense Complete — Check Parking Position Your vehicle is now in the perpendicular park position.
Page 407: Lanesense - If Equipped
STARTING AND OPERATING 405 LANESENSE — IF EQUIPPED WARNING! (Continued) LaneSense Operation and blind spots before backing up and moving for- ward. You are responsible for safety and must continue The LaneSense system is operational at speeds above to pay attention to your surroundings. Failure to do so 37 mph (60 km/h) and below 112 mph (180 km/h).
Page 408: Turning Lanesense On Or Off
406 STARTING AND OPERATING the driver to remain within the lane. When only a single lane marking is detected, a haptic (torque) warning will not be provided. NOTE: When operating conditions have been met, the LaneSense system will monitor if the driver’s hands are on the steering wheel and provides an audible and visual warning to the driver when the driver’s hands are not detected on the steering wheel.
Page 409 STARTING AND OPERATING 407 • When the LaneSense system senses the lane has been Instrument Cluster Display approached and is in a lane departure situation, the When the LaneSense system is ON; the lane lines are gray visual warning in the instrument cluster display will when both of the lane boundaries have not been detected show the left inside lane line flashing yellow (on/off), and the LaneSense telltale...
Page 410 408 STARTING AND OPERATING Left Lane Departure — Both Lane Lines Detected The LaneSense telltale changes from solid green to solid yellow. At this time torque is applied to the • When the LaneSense system is ON, the lane lines turn steering wheel in the opposite direction of the lane from gray to white.
Page 411: Changing Lanesense Status
STARTING AND OPERATING 409 changes from solid yellow to flashing yellow. At Changing LaneSense Status this time torque is applied to the steering wheel in the The LaneSense system has settings to adjust the intensity of opposite direction of the lane boundary. the torque warning and the warning zone sensitivity •...
Page 412 410 STARTING AND OPERATING After five seconds, this note will disappear. The ParkView When the vehicle is shifted out of REVERSE (with camera Rear Back Up Camera is located on the rear of the vehicle delay turned on), the camera image will continue to be above the rear license plate.
Page 413 STARTING AND OPERATING 411 The following table shows the approximate distances for each zone: Zone Distance To The Rear Of The Vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green 6.5 ft or greater (2 m or greater) NOTE: If snow, ice, mud, or any foreign substance builds...
Page 414: Surround View Camera System - If Equipped
412 STARTING AND OPERATING SURROUND VIEW CAMERA SYSTEM — IF When the vehicle is shifted into REVERSE, the rear camera EQUIPPED view and top view is the default view of the system. Your vehicle may be equipped with the Surround View When the vehicle is shifted out of REVERSE (with camera Camera System that allows you to see an on-screen image delay turned on), the camera image will continue to be...
Page 415 STARTING AND OPERATING 413 The following table shows the approximate distances for each zone: Zone Distance To The Rear Of The Vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green 6.5 ft or greater (2 m or greater) Modes Of Operation...
Page 416 414 STARTING AND OPERATING NOTE: Front View • Front tires will be in image when the tires are turned. The Front view will show you what is immediately in front of the vehicle and • Due to wide angle cameras in mirror, the image will is always paired with the Top view of appear distorted.
Page 417: Refueling The Vehicle
STARTING AND OPERATING 415 • The camera delay system is turned off manually through CAUTION! the Uconnect settings menu. Refer to “Uconnect Set- • To avoid vehicle damage, Surround View should tings” in “Multimedia” for further information. only be used as a parking aid. The Surround View NOTE: camera is unable to view every obstacle or object in •...
Page 418 416 STARTING AND OPERATING WARNING! (Continued) and may cause the “Malfunction Indicator Light” to turn on. • A fire may result if fuel is pumped into a portable container that is inside of a vehicle. You could be burned. Always place fuel containers on the ground while filling.
Page 419: Vehicle Loading
STARTING AND OPERATING 417 NOTE: The label also specifies maximum capacities of front and rear axle systems (GAWR). Total load must be limited so • In certain cold conditions, ice may prevent the fuel filler GVWR and front and rear GAWR are not exceeded. door from opening.
Page 420 418 STARTING AND OPERATING Rim Size determined separately to be sure that the load is properly distributed over the front and rear axle. Weighing the This is the rim size that is appropriate for the tire size vehicle may show that the GAWR of either the front or rear listed.
Page 421: Trailer Towing
STARTING AND OPERATING 419 TRAILER TOWING Gross Trailer Weight (GTW) In this section you will find safety tips and information on The GTW is the weight of the trailer plus the weight of all limits to the type of towing you can reasonably do with cargo, consumables and equipment (permanent or tempo- your vehicle.
Page 422 420 STARTING AND OPERATING Tongue Weight (TW) other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they The tongue weight is the downward force exerted on the are commonly used to tow small and medium sized hitch ball by the trailer.
Page 423: Trailer Hitch Classification
STARTING AND OPERATING 421 Trailer Hitch Classification WARNING! The following chart provides the industry standard for the • An improperly adjusted Weight Distributing Hitch maximum trailer weight a given trailer hitch class can tow system may reduce handling, stability, braking per- and should be used to assist you in selecting the correct formance, and could result in a collision.
Page 424: Trailer Towing Weights (Maximum Trailer Weight Ratings)
422 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Max. GTW Engine/ Trailer Tow Max. Tongue Combined Frontal Area (Gross Trailer Transmission Package Weight Weight Rating)
Page 425 STARTING AND OPERATING 423 2. Determine occupant count. 4 Occupants (at 150 lbs [68 kg]) + Max Trailer = • For calculation purposes, average weight of an occu- • 1505 lbs (682 kg) – 600 lbs (272 kg) (4 x 150 lbs [68 kg]) pant is 150 lb (68 kg).
Page 426: Trailer And Tongue Weight
424 STARTING AND OPERATING Number Of Persons / Weight Of Occupants Max Cargo No Tongue Load, Max Cargo With Trailer Max Trailer Max Trailer 360 lb (136 kg) Tongue Load 455 lbs (206 kg) – 360 lbs (163 kg) = 95 lbs (43 kg) 455 lbs (206 kg) 95 lbs (43 kg)
Page 427: Towing Requirements
STARTING AND OPERATING 425 Consider the following items when computing the weight CAUTION! (Continued) on the rear axle of the vehicle: • Then, during the first 500 miles (805 km) that a trailer • The tongue weight of the trailer. is towed, do not drive over 50 mph (80 km/h) and do •...
Page 428 426 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • When hauling cargo or towing a trailer, do not 2. GTW overload your vehicle or trailer. Overloading can 3. GAWR cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, sus- 4.
Page 429 STARTING AND OPERATING 427 • When replacing tires, refer to “Tires” in “Servicing And WARNING! Maintenance” for the proper tire replacement proce- • Do not connect trailer brakes to your vehicle’s hy- dures. Replacing tires with a higher load carrying capac- ity will not increase the vehicle’s GVWR and GAWR draulic brake lines.
Page 430 428 STARTING AND OPERATING Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four- and seven-pin wiring harness.
Page 431: Towing Tips
STARTING AND OPERATING 429 Automatic Transmission Select the DRIVE range when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. For increased engine braking on steep down- hill grades, select the LOW range. Speed Control — If Equipped •...
Page 432: Recreational Towing
430 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF The Ground All Models Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer NOTE: Recreational Towing — All Models •...
Page 433: Driving Tips
STARTING AND OPERATING 431 Recreational towing is allowed ONLY if the front wheels DRIVING TIPS are OFF the ground. This may be accomplished using a tow Driving On Slippery Surfaces dolly (front wheels off the ground) or vehicle trailer (all Information in this section will aid in safe controlled four wheels off the ground).
Page 434: Driving Through Water
432 STARTING AND OPERATING complete loss of vehicle control and stopping ability. To Flowing/Rising Water reduce this possibility, the following precautions should be observed: WARNING! • Slow down during rainstorms or when the roads are Do not drive on or across a road or path where water is slushy.
Page 435 STARTING AND OPERATING 433 WARNING! (Continued) CAUTION! (Continued) • Driving through standing water limits your vehicle’s • Driving through standing water may cause damage braking capabilities, which increases stopping dis- to your vehicle’s drivetrain components. Always in- tances. Therefore, after driving through standing spect your vehicle’s fluids (i.e., engine oil, transmis- water, drive slowly and lightly press on the brake sion, axle, etc.) for signs of contamination (i.e., fluid...
Page 437 IN CASE OF EMERGENCY CONTENTS ▫ Jacking Instructions .....462 HAZARD WARNING FLASHERS ... .437 ▫...
Page 438 436 IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE ... .496 EVENT DATA RECORDER (EDR) ... .499 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) .
Page 439: Hazard Warning Flashers
IN CASE OF EMERGENCY 437 HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located in the lower center area of the instrument panel. Push the switch to turn on the Hazard Warning flasher.
Page 440 438 IN CASE OF EMERGENCY • Roadside Assistance – If you get a flat tire, or need a tow, WARNING! just push the ASSIST button and you’ll be connected to someone who can help. Roadside Assistance will know ALWAYS obey traffic laws and pay attention to the what vehicle you’re driving and its location.
Page 441 IN CASE OF EMERGENCY 439 3. Once a connection between the vehicle and a SOS NOTE: operator is made, the SOS Call system may transmit the • Your vehicle may be transmitting data as authorized following important vehicle information to a SOS op- by the subscriber.
Page 442 440 IN CASE OF EMERGENCY WARNING! (Continued) WARNING! (Continued) APPS AND SERVICES, AMONG OTHERS, WILL Emergency Services Agent. All occupants should exit the vehicle immediately and move to a safe location. NOT OPERATE. • Modifications to any part of the SOS Call system •...
Page 443 IN CASE OF EMERGENCY 441 • An In-Vehicle Audio message will state “Vehicle device • The vehicle’s electrical systems are not intact. requires service. Please contact your dealer.” • The SOS Call system software and/or hardware are damaged during a crash. WARNING! •...
Page 444 442 IN CASE OF EMERGENCY General Information WARNING! (Continued) This device complies with Part 15 of the FCC Rules. applications when it is safe to do so. Failure to do so Operation is subject to the following two conditions: (1) may result in an accident involving serious injury or This device may not cause harmful interference, and (2) death.
Page 445: Bulb Replacement
IN CASE OF EMERGENCY 443 BULB REPLACEMENT Replacement Bulbs Interior Bulbs Lamps Bulb Number Center & Rear Dome Lamp LED (Serviced At Authorized Dealer) Center & Rear Reading Lamps LED (Serviced At Authorized Dealer) Front Door Courtesy Lamp LED (Serviced At Authorized Dealer) Front Header Reading Lamps –...
Page 446 444 IN CASE OF EMERGENCY Lamps Bulb Number Dedicated Daytime Running Lamp (If Equipped) LED (Serviced at Authorized Dealer) Front Turn Signal Lamp PWY24WNA (If Halogen Headlamp Equipped) PWY24WSV (If HID Headlamp Equipped) Side Marker Lamp Front Park Lamp PWY24WNA (If Bulb Equipped) LED (Serviced At Authorized Dealer) Front Fog Lamp H11LL...
Page 447: Replacing Exterior Bulbs
IN CASE OF EMERGENCY 445 Replacing Exterior Bulbs Halogen Headlamps High Intensity Discharge (HID) Headlamps — If 1. Reach behind the headlamp housing to access the Equipped headlamp bulb cap. The headlamps contain a type of high voltage discharge 2. Firmly grasp the headlamp bulb cap and rotate it light source.
Page 448 446 IN CASE OF EMERGENCY 3. Firmly grasp the headlamp bulb socket assembly and rotate counterclockwise to remove from the housing. Headlamp Bulb CAUTION! Headlamp Bulb Socket 4. Disconnect the bulb from the electrical connector and Do not touch the new bulb with your fingers. Oil then connect the replacement bulb.
Page 449 IN CASE OF EMERGENCY 447 Front Turn Signal Lamp Front And Rear Side Marker Lamps 1. Open the hood. 1. Remove the three fasteners from the inner wheel liner and carefully peel back liner for access. 2. Twist the front turn signal lamp socket assembly coun- terclockwise, and then remove the front turn signal lamp assembly from the lamp housing.
Page 450 448 IN CASE OF EMERGENCY Front Fog Lamp — Halogen 1. Remove fasteners from inner wheel liner and carefully peel back liner for access. 2. Reach through the front fascia to fog lamp housing to access the bulb. 3. Rotate the front fog lamp bulb counterclockwise, and remove the bulb from the front fog lamp housing.
Page 451 IN CASE OF EMERGENCY 449 Rear Bodyside Mounted Taillamps CAUTION! 1. Raise the liftgate. Do not touch the new bulb with your fingers. Oil 2. Remove two torx head screws on bodyside lamp using contamination will severely shorten bulb life. If the a T30 screwdriver.
Page 452: Fuses
450 IN CASE OF EMERGENCY FUSES General Information The fuses protect electrical systems against excessive current. WARNING! When a device does not work, you must check the fuse • When replacing a blown fuse, always use an appro- element inside the blade fuse for a break/melt. priate replacement fuse with the same amp rating as Also, please be aware that when using power outlets for the original fuse.
Page 453: Fuse Location
IN CASE OF EMERGENCY 451 Fuse Location After service is done, secure the cover with its two locks. The fuses are grouped into a controller located in the engine compartment. Underhood Fuses The Power Distribution Center is located in the engine compartment near the battery.
Page 454 452 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not Used – 5 Amp Tan Battery Sensor (IBS) – 10 Amp Red ECM (ESS Only) – 10 Amp Red 40 Amp Green –...
Page 455 IN CASE OF EMERGENCY 453 Cavity Cartridge Fuse Blade Fuse Description F25A – 10 Amp Red HANDSFREE LT & RT RR Door release mod F25B – 10 Amp Red Active Grill Shutter/ PWR Mirror 40 Amp Green – Front HVAC Blower Motor 25 Amp Clear –...
Page 456 454 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description 60 Amp Yellow – Vacuum Cleaner 25 Amp Clear – Rear HVAC Blower Motor – – Not Used – – Not Used 40 Amp Green – Folding Seat Module –...
Page 457 IN CASE OF EMERGENCY 455 Cavity Cartridge Fuse Blade Fuse Description F55A – 15 Amp Blue Radio Frequency HUB/ Keyless ignition system (KIN) / (Electronic Steering Lock-BUX ONLY) F55B – 15 Amp Blue DVD / Video Routing Module (VRM F56A –...
Page 458 456 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – 20 Amp Yellow Trailer Tow Left Stop/Turn — If Equipped – 15 Amp Blue RT HID Headlamp – – Not Used – 15 Amp Blue Instrument Panel Cluster (IPC) –...
Page 459 IN CASE OF EMERGENCY 457 Cavity Cartridge Fuse Blade Fuse Description – 5 Amp Tan Overhead Console / RR ISC – 20 Amp Yellow Uconnect/DCSD/ Telematics F77A – 10 Amp Red RR Entertainment Screen 1 & 2/Media HUB 1 & 2/3rd Row USB Charge Only/ 2nd Row USB Charge Only/Vaccum Cleaner SW/...
Page 460 458 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – – Not Used 20 Amp Blue – TT Park Lights — If Equipped 30 Amp Pink – Headlamp Washer Pump — If Equipped – – Not Used – 20 Amp Yellow Cigar Lighter –...
Page 461 IN CASE OF EMERGENCY 459 Cavity Cartridge Fuse Blade Fuse Description – 10 Amp Red Occupant Restraint Con- troller (ORC) (Airbag) – 10 Amp Red Occupant Restraint Con- troller (ORC) (Airbag) – 15 Amp Blue Left HID Headlamp 30 Amp Pink –...
Page 462: Jacking And Tire Changing - If Equipped
460 IN CASE OF EMERGENCY JACKING AND TIRE CHANGING — IF EQUIPPED Jack And Spare Tire Location The jacking tools, spare tire and portable air compressor (if WARNING! equipped) or tire service kit (if equipped) are stowed behind an access panel on the left hand side of the vehicle. •...
Page 463: Preparations For Jacking
IN CASE OF EMERGENCY 461 Inflatable Spare Tire and gently remove it from the 3. Remove Jack by turning the jack screw counterclockwise storage area. Remove wrench from foam tray. to collapse from storage area that is located behind the tire.
Page 464: Jacking Instructions
462 IN CASE OF EMERGENCY Jacking Instructions WARNING! WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the Carefully follow these tire changing warnings to help road to avoid being hit when operating the jack or prevent personal injury or damage to your vehicle: changing the wheel.
Page 465 IN CASE OF EMERGENCY 463 Jack Warning Label Extending The Wrench 1. Loosen (but do not remove) the wheel lug nuts by CAUTION! turning them to the left one turn while the wheel is still on the ground. Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle.
Page 466 464 IN CASE OF EMERGENCY 2. There are two jack engagement locations on each side of WARNING! the vehicle body. These locations are on the sill flange of the vehicle body. Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
Page 467 IN CASE OF EMERGENCY 465 Front Jack Engaged Rear Jacking Location...
Page 468 466 IN CASE OF EMERGENCY obtained to install the compact spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
Page 469 IN CASE OF EMERGENCY 467 nuts with wrench. After inflation, once the vehicle is lowered you will have a second opportunity to “torque” the lug nuts. 8. Inflate the tire to the prescribed pressure 60 psi (4.2 Bar) using the Portable Air Compressor or Tire Service Kit if equipped.
Page 470: Road Tire Installation
468 IN CASE OF EMERGENCY 11. Lower the jack to its fully-closed position. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided.
Page 471 IN CASE OF EMERGENCY 469 the lug nuts with the cone shaped end of the nut toward 4. Install the remaining lug nuts with the cone shaped end the wheel. Lightly tighten the lug nuts. of the nut toward the wheel. Lightly tighten the lug nuts.
Page 472 470 IN CASE OF EMERGENCY Vehicles Without Wheel Covers 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased 1. Mount the road tire on the axle. leverage. Tighten the lug nuts in a star pattern until each 2.
Page 473: Portable Air Compressor - If Equipped
IN CASE OF EMERGENCY 471 Portable Air Compressor — If Equipped Portable Air Compressor Usage With Inflatable Spare Tire Your vehicle may be equipped with a Portable Air Com- pressor. Use the Portable Air Compressor located in the 1. Remove the Portable Air Compressor from the storage side compartment of the cargo area to inflate the inflatable location.
Page 474 472 IN CASE OF EMERGENCY 4. Uncoil the power plug and connect it 7. Inflate the tire to 60 psi (4.2 Bar) the vehicles 12 Volt power Outlet. recommended as per the label on the wheel or if the vehicle equipped with the inflatable spare tire pressure indi- cated on the Tire and Loading infor- mation label located on the driver-...
Page 475: Tire Service Kit For Inflating Tire - If Equipped
IN CASE OF EMERGENCY 473 10. Return the Portable Air Compressor to the foam tray Tire Service Kit And Components And Operation and secure it with the strap. Store the foam tray in the cargo area. WARNING! • Do not lift or carry the Portable Air Compressor by the hose.
Page 476 474 IN CASE OF EMERGENCY Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button once symbols to indicate the air or sealant mode. to turn On the Tire Service Kit.
Page 477 IN CASE OF EMERGENCY 475 2. Verify that the valve stem (on the wheel with the WARNING! (Continued) deflated tire) is in a position that is near to the ground. provided. Failure to follow these warnings can result This will allow the Tire Service Kit Hose to reach the in injuries that are serious or fatal to you, your valve stem and keep the Tire Service Kit flat on the passengers, and others around you.
Page 478 476 IN CASE OF EMERGENCY 3. Uncoil the Power Plug and insert the 8. Switch the power button ON. plug into the vehicle’s 12 Volt power outlet. 4. Place the Tire Service Kit on the ground next to the 9. Inflate the tire to 60 psi (4.2 Bar) deflated tire.
Page 479: Return Inflatable Spare Tire
IN CASE OF EMERGENCY 477 11. Remove the speed limit label sticker 4. Install the foam tray with wrench and funnel installed. from the Tire Service Kit and place it 5. Install and tighten the wing nut by hand. on the center of the steering wheel. 6.
Page 480 478 IN CASE OF EMERGENCY Tire Service Kit Storage Tire Service Kit And Components And Operation The Tire Service Kit is secured with a strap and is stored in the storage bin located behind the rear cargo trim panel. Tire Service Kit Components 1 —...
Page 481 IN CASE OF EMERGENCY 479 Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button once symbols to indicate the air or sealant mode. to turn On the Tire Service Kit.
Page 482 480 IN CASE OF EMERGENCY • The Sealant Bottle is a one tire application use and needs and make sure the Mode Select Knob is in the Air Mode to be replaced after each use. Always replace these when inflating such items to avoid injecting sealant into components immediately at your original equipment them.
Page 483 IN CASE OF EMERGENCY 481 Sealing A Tire With Tire Service Kit WARNING! (Continued) Whenever You Stop To Use Tire Service Kit: • Keep Tire Service Kit away from open flames or heat source. 1. Pull over to a safe location and turn on the vehicle’s •...
Page 484 482 IN CASE OF EMERGENCY 3. Remove the cap from the valve stem 2. Ensure the Mode Select Knob is to the and then screw the fitting at the end Sealant Mode position. of the Sealant Hose onto the valve stem.
Page 485 IN CASE OF EMERGENCY 483 If the sealant (white fluid) does not flow within 0 – 10 If the sealant (white fluid) does flow through the Sealant seconds through the Sealant Hose: Hose: 1. Push the Power Button to turn Off the Tire Service Kit. 1.
Page 486 484 IN CASE OF EMERGENCY If the tire does not inflate to at least 26 psi (1.8 Bar) Drive Vehicle: pressure within 15 minutes: Immediately after injecting sealant and • The tire is too badly damaged. Do not attempt to drive inflating the tire, drive the vehicle the vehicle further.
Page 487 IN CASE OF EMERGENCY 485 After Driving: 5. Uncoil the Hose and screw the fitting at the end of the hose onto the valve Pull over to a safe location. Refer to “Whenever You Stop stem. To Use Tire Service Kit” in this section before continuing. 1.
Page 488 486 IN CASE OF EMERGENCY If the tire pressure is 19 psi (1.3 Bar) or higher: 6. Replace the Sealant Bottle at an authorized dealer as soon as possible. Refer to “Sealant Bottle Replacement”. 1. Push the Power Button to turn on Tire Service Kit and inflate the tire to NOTE: When having the tire serviced, advise the autho- the cold tire inflation pressure found...
Page 489 IN CASE OF EMERGENCY 487 3. Remove the bottle cover. 4. Rotate the bottle up beyond vertical to release. Remove The Bottle Cover Rotate The Bottle Up...
Page 490: Jump Starting
488 IN CASE OF EMERGENCY 5. Pull the bottle away from the Compressor. JUMP STARTING If your vehicle has a discharged battery it can be jump started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump starting can be dangerous if done improperly so please follow the procedures in this section carefully.
Page 491: Preparations For Jump Start
IN CASE OF EMERGENCY 489 Preparations For Jump Start The battery in your vehicle is located on the left side of the engine compartment. Negative Jump Starting Location WARNING! • Take care to avoid the radiator cooling fan whenever Positive Jump Starting Location the hood is raised.
Page 492: Jump Starting Procedure
490 IN CASE OF EMERGENCY Jump Starting Procedure WARNING! (Continued) flammable and explosive. Keep open flames or WARNING! sparks away from the battery. Failure to follow this jump starting procedure could 1. Apply the parking brake, shift the automatic transmis- result in personal injury or property damage due to sion into PARK and place the ignition to OFF.
Page 493: Refueling In Emergency
IN CASE OF EMERGENCY 491 4. Connect the opposite end of the negative (-) jumper 3. Disconnect the positive (+) end of the jumper cable from cable to the negative post near the windshield cowl the positive (+) post of the booster battery. (exposed metal part of the discharged vehicle’s engine).
Page 494: If Your Engine Overheats
492 IN CASE OF EMERGENCY NOTE: There are steps that you can take to slow down an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.
Page 495: Manual Park Release
IN CASE OF EMERGENCY 493 CAUTION! (Continued) stop the vehicle. Idle the vehicle with the air condi- tioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. MANUAL PARK RELEASE WARNING! You should be seated in the driver’s seat with your foot...
Page 496: Freeing A Stuck Vehicle
494 IN CASE OF EMERGENCY go, then release it. The transmission should now be in FREEING A STUCK VEHICLE NEUTRAL, allowing the vehicle to be moved. If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering NOTE: When the lever is locked in the released position, wheel right and left to clear the area around the front the tether will remain outside of the trim panel and the...
Page 497 IN CASE OF EMERGENCY 495 WARNING! CAUTION! (Continued) for at least one minute after every five rocking- Fast spinning tires can be dangerous. Forces generated motion cycles. This will minimize overheating and by excessive wheel speeds may cause damage, or even reduce the risk of transmission failure during pro- failure, of the axle and tires.
Page 498 496 IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheel OFF The Ground ALL MODELS Flat Tow NONE NOT ALLOWED Wheel Lift Or Dolly Tow Front Rear NOT ALLOWED...
Page 499 IN CASE OF EMERGENCY 497 • Use approved receptacle location to free the disabled If flatbed equipment is not available, this vehicle must towed with the front wheels OFF the ground (using a vehicle from its environment. towing dolly, or wheel lift equipment with the front wheels raised).
Page 500 498 IN CASE OF EMERGENCY If the key fob is unavailable, or the vehicle’s battery is CAUTION! (Continued) discharged, refer to “Manual Park Release” in this section • Is NOT to be used for transporting the vehicle over for instructions on shifting the transmission out of PARK in the road, i.e.
Page 501 IN CASE OF EMERGENCY 499 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. Please refer to “Occupant Restraint Systems” in “Safety” for further information on the Enhanced Accident Re- sponse System (EARS) function. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR).
Page 503 SERVICING AND MAINTENANCE CONTENTS ▫ Body Lubrication ..... .517 SCHEDULED SERVICING ....503 ▫...
Page 504 502 SERVICING AND MAINTENANCE ▫ Tire Rotation Recommendations ... .554 ▫ Body And Underbody Maintenance ..557 ▫ Preserving The Bodywork ....558 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES .
Page 505: Scheduled Servicing
SERVICING AND MAINTENANCE 503 SCHEDULED SERVICING NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 Your vehicle is equipped with an automatic oil change hours of engine run time, whichever comes first. The 350 indicator system.
Page 506: Maintenance Plan
504 SERVICING AND MAINTENANCE Maintenance Plan Required Maintenance Intervals Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter •...
Page 507 SERVICING AND MAINTENANCE 505 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Inspect front accessory drive belt, tensioner, idler pulley, and replace if necessary Additional Maintenance...
Page 508: Heavy Duty Use Of The Vehicle
506 SERVICING AND MAINTENANCE Heavy Duty Use Of The Vehicle WARNING! Change engine oil at 4,000 miles (6,500 km) or 350 hours of • You can be badly injured working on or around a engine run time if the vehicle is operated in a dusty and off motor vehicle.
Page 509: Engine Compartment
SERVICING AND MAINTENANCE 507 ENGINE COMPARTMENT 3.6L Engine 1 — Engine Coolant Pressure Cap 5 — Power Distribution Center (Fuses) 2 — Engine Oil Fill 6 — Battery 3 — Brake Fluid Reservoir 7 — Engine Oil Dipstick 4 — Engine Air Cleaner 8 —...
Page 510: Checking Oil Level
508 SERVICING AND MAINTENANCE Checking Oil Level Adding Washer Fluid To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut OFF.
Page 511: Maintenance-Free Battery
SERVICING AND MAINTENANCE 509 To prevent freeze-up of your windshield washer system in WARNING! (Continued) cold weather, select a solution or mixture that meets or large amounts of water. Refer to “Jump Starting exceeds the temperature range of your climate. This rating Procedure”...
Page 512: Dealer Service
510 SERVICING AND MAINTENANCE CAUTION! (Continued) WARNING! (Continued) • If a “fast charger” is used while the battery is in the have any doubt about your ability to perform a service vehicle, disconnect both vehicle battery cables before job, take your vehicle to a competent mechanic. connecting the charger to the battery.
Page 513 SERVICING AND MAINTENANCE 511 American Petroleum Institute (API) Engine Oil Engine Oil Viscosity Identification Symbol Mopar SAE 0W-20 engine oil approved to FCA Material Standard MS-6395 such as Pennzoil, Shell Helix or equiva- This symbol means that the oil has lent is recommended for all operating temperatures.
Page 514: Engine Oil Filter
512 SERVICING AND MAINTENANCE Materials Added To Engine Oil Engine Air Cleaner Filter The manufacturer strongly recommends against the addi- Refer to the “Maintenance Plan” in this section for the tion of any additives (other than leak detection dyes) to the proper maintenance intervals.
Page 515: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 513 Accessory Drive Belt Inspection WARNING! • Do not attempt to inspect an accessory drive belt with vehicle running. • When working near the radiator cooling fan, discon- nect the fan motor lead. The fan is temperature controlled and can start at any time regardless of ignition mode.
Page 516: Air Conditioner Maintenance
514 SERVICING AND MAINTENANCE • Noise (objectionable squeal, squeak, or rumble is heard WARNING! (Continued) or felt while drive belt is in operation) Warranty Information Book, located in your owner’s Some conditions can be caused by a faulty component such information kit, for further warranty information.
Page 517 SERVICING AND MAINTENANCE 515 NOTE: Use only manufacturer approved A/C system PAG compressor oil, and refrigerants. Air Conditioning Filter Replacement (Cabin Air Filter) Refer to “Scheduled Servicing” in this section for the proper maintenance intervals. WARNING! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the ACC or ON/ RUN mode.
Page 518 516 SERVICING AND MAINTENANCE inward on each travel stop, and pull the glove compart- lid from the snap. Once detached, remove the rest of the ment door down until the travel stops pass clear of their snap completely from the compartment cover. hooking points.
Page 519: Body Lubrication
SERVICING AND MAINTENANCE 517 pulling out the filter cover to expose the cabin air filter. Body Lubrication Remove the air filter by pulling it straight out of the Locks and all body pivot points, including such items as housing. seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be 8.
Page 520: Windshield Wiper Blades
518 SERVICING AND MAINTENANCE Windshield Wiper Blades The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems Clean the rubber edges of the wiper blades and the are experienced. This inspection should include the follow- windshield periodically with a sponge or soft cloth and a ing points: mild nonabrasive cleaner.
Page 521 SERVICING AND MAINTENANCE 519 Front Wiper Blade Removal/Installation CAUTION! Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged. 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position.
Page 522 520 SERVICING AND MAINTENANCE the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. Wiper Blade Removed From Wiper Arm 1 — Wiper Blade Wiper Blade With Release Tab In Unlocked Position 2 —...
Page 523 SERVICING AND MAINTENANCE 521 2. Position the wiper blade near the hook on the tip of the NOTE: The rear wiper arm cannot be fully raised off the wiper arm with the wiper release tab open and the blade glass unless the wiper arm pivot cap is unsnapped first. side of the wiper facing up and away from the wind- Attempting to fully raise the rear wiper arm without shield.
Page 524 522 SERVICING AND MAINTENANCE 2. Lift the rear wiper arm fully off the glass. NOTE: Resistance will be accompanied by an audible snap. 4. Still grasping the bottom end of the wiper blade, move the wiper blade upward and away from the wiper arm to disengage.
Page 525: Exhaust System
SERVICING AND MAINTENANCE 523 Installing The Rear Wiper If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; 1. Lift the rear wiper arm pivot cap away from the glass to or when the underside or rear of the vehicle is damaged;...
Page 526: Cooling System
524 SERVICING AND MAINTENANCE In unusual situations involving grossly malfunctioning CAUTION! engine operation, a scorching odor may suggest severe and • The catalytic converter requires the use of unleaded abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, fuel only.
Page 527 SERVICING AND MAINTENANCE 525 Check the engine cooling system hoses for brittle rubber, WARNING! (Continued) cracking, tears, cuts, and tightness of the connection at the do not open the hood until the radiator has had time coolant recovery bottle and radiator. Inspect the entire to cool.
Page 528 526 SERVICING AND MAINTENANCE • This vehicle has not been designed for use with propyl- Selection Of Coolant ene glycol-based engine coolant (antifreeze). Use of Refer to “Fluids And Lubricants” in “Technical Specifica- propylene glycolbased engine coolant (antifreeze) is not tions”...
Page 529 SERVICING AND MAINTENANCE 527 Please review these recommendations for using Organic NOTE: Additive Technology (OAT) engine coolant (antifreeze) • It is the owner’s responsibility to maintain the proper that meets the requirements of FCA Material Standard level of protection against freezing according to the MS.90032.
Page 530 528 SERVICING AND MAINTENANCE The cap should be inspected and cleaned if there is any Coolant Level accumulation of foreign material on the sealing surfaces. The coolant expansion bottle provides a quick visual method for determining that the coolant level is adequate. WARNING! With the engine off and cold, the level of the coolant (antifreeze) in the bottle should be between the “MAX”...
Page 531: Brake System
SERVICING AND MAINTENANCE 529 If an examination of your engine compartment shows no the correct type thermostat. Other designs may result in evidence of radiator or hose leaks, the vehicle may be unsatisfactory engine coolant (antifreeze) performance, safely driven. The vapor will soon dissipate. poor gas mileage, and increased emissions.
Page 532 530 SERVICING AND MAINTENANCE level up to the requirements described on the brake fluid WARNING! (Continued) reservoir. With disc brakes, fluid level can be expected to • To avoid contamination from foreign matter or mois- fall as the brake pads wear. Brake fluid level should be ture, use only new brake fluid or fluid that has been checked when pads are replaced.
Page 533: Automatic Transmission
SERVICING AND MAINTENANCE 531 Automatic Transmission Special Additives The manufacturer strongly recommends against using any Selection Of Lubricant special additives in the transmission. Automatic Transmis- It is important to use the proper transmission fluid to sion Fluid (ATF) is an engineered product and its perfor- ensure optimum transmission performance and life.
Page 534: Raising The Vehicle
532 SERVICING AND MAINTENANCE fluid level checked. Operating the vehicle with an im- RAISING THE VEHICLE proper fluid level can cause severe transmission damage. In the case where it is necessary to raise the vehicle, go to an authorized dealer or service station. CAUTION! TIRES If a transmission fluid leak occurs, visit an authorized...
Page 535 SERVICING AND MAINTENANCE 533 Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
Page 536 534 SERVICING AND MAINTENANCE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 537 SERVICING AND MAINTENANCE 535 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions –...
Page 538 536 SERVICING AND MAINTENANCE Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 539 SERVICING AND MAINTENANCE 537 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 540 538 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 541 SERVICING AND MAINTENANCE 539 Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 542 540 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult (1) Locate the statement “The combined weight of this manual to determine how this reduces the available occupants and cargo should never exceed XXX kg or cargo and luggage load capacity of your vehicle.
Page 543 SERVICING AND MAINTENANCE 541 • For the following example, the combined weight of occu- pants and cargo should never exceed 865 lbs (392 kg). WARNING! WARNING! (Continued) increase your stopping distance. Use tires of the rec- Overloading of your tires is dangerous. Overloading ommended load capacity for your vehicle.
Page 544: Tires - General Information
542 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 545 SERVICING AND MAINTENANCE 543 Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 546 544 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 547 SERVICING AND MAINTENANCE 545 Run Flat Tires — If Equipped Tire Spinning Run Flat tires allow you the capability to drive 50 miles When stuck in mud, sand, snow, or ice conditions, do not (80 km) at 50 mph (80 km/h) after a rapid loss of inflation spin your vehicle’s wheels above 30 mph (48 km/h) or for pressure.
Page 548 546 SERVICING AND MAINTENANCE Tread Wear Indicators worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for Tread wear indicators are in the original equipment tires to further information. help you in determining when your tires should be re- placed.
Page 549 SERVICING AND MAINTENANCE 547 It is recommended to replace the two front tires or two rear WARNING! (Continued) tires as a pair. Replacing just one tire can seriously affect You could lose control and have a collision resulting in your vehicle’s handling. If you ever replace a wheel, make serious injury or death.
Page 550: Tire Types
548 SERVICING AND MAINTENANCE tire sidewall. Use all season tires only in sets of four; failure WARNING! (Continued) to do so may adversely affect the safety and handling of • Never use a tire with a smaller load index or capacity, your vehicle.
Page 551: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 549 Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 552 550 SERVICING AND MAINTENANCE spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 553: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 551 use spare wheel. This label contains the driving limitations WARNING! for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Compact and Collapsible spares are for temporary Installation of this limited use spare tire affects vehicle emergency use only.
Page 554 552 SERVICING AND MAINTENANCE and to prevent corrosion. Wash wheels with the same soap wheel cleaning chemicals and equipment to prevent dam- solution recommended for the body of the vehicle and age to the wheels. Mopar Wheel Treatment or Mopar remember to always wash when the surfaces are not hot to Chrome Cleaner or their equivalent is recommended or the touch.
Page 555: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 553 Dark Vapor Chrome, Black Satin Chrome, or Low Gloss WARNING! Clear Coat Wheels Using tires of different size and type (M+S, Snow) CAUTION! between front and rear axles can cause unpredictable handling. You could lose control and have a collision. If your vehicle is equipped with these specialty wheels, DO NOT USE wheel cleaners, abrasives, or CAUTION!
Page 556: Tire Rotation Recommendations
554 SERVICING AND MAINTENANCE The suggested rotation method is the “forward cross” CAUTION! (Continued) shown in the following diagram. This rotation pattern does • Observe the traction device manufacturer’s instruc- not apply to some directional tires that must not be tions on the method of installation, operating speed, reversed.
Page 557: Treadwear
SERVICING AND MAINTENANCE 555 All passenger vehicle tires must conform to Federal WARNING! safety requirements in addition to these grades. The traction grade assigned to this tire is based on Treadwear straight-ahead braking traction tests, and does not The Treadwear grade is a comparative rating, based on include acceleration, cornering, hydroplaning, or the wear rate of the tire when tested under controlled peak traction characteristics.
Page 558: Storing The Vehicle
556 SERVICING AND MAINTENANCE • Clean and protect polished metal parts by applying WARNING! protective waxes. The temperature grade for this tire is established for • Apply talcum powder to the front and rear wiper blades a tire that is properly inflated and not overloaded. and leave raised from the glass.
Page 559: Bodywork
SERVICING AND MAINTENANCE 557 What Causes Corrosion? CAUTION! Corrosion is the result of deterioration or removal of paint Before removal of the positive and negative terminals and protective coatings from your vehicle. to the battery, wait at least a minute with ignition The most common causes are: switch in the OFF position and close the drivers door.
Page 560: Preserving The Bodywork
558 SERVICING AND MAINTENANCE Do not use abrasive cleaning components, solvents, steel CAUTION! (Continued) wool or other aggressive material to clean the lenses. • Use of power washers exceeding 1,200 psi (8,274 kPa) Preserving The Bodywork can result in damage or removal of paint and decals. Washing Special Care •...
Page 561: Interiors
SERVICING AND MAINTENANCE 559 • If a lot of driving is done on gravel roads, consider mud Seat Belt Maintenance or stone shields behind each wheel. Do not bleach, dye or clean the belts with chemical solvents • Use Mopar Touch Up Paint on scratches as soon as or abrasive cleaners.
Page 562: Plastic And Coated Parts
560 SERVICING AND MAINTENANCE Plastic And Coated Parts Leather Parts Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended for leather upholstery. CAUTION! Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can •...
Page 563: Glass Surfaces
SERVICING AND MAINTENANCE 561 CAUTION! Do not use Alcohol and Alcohol-based and/or Ketone based cleaning products to clean leather seats, as damage to the seat may result. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner, or any commercial household-type glass cleaner.
Page 565 TECHNICAL SPECIFICATIONS CONTENTS ▫ Do Not Use E-85 In Non-Flex Fuel Vehicles ..568 IDENTIFICATION DATA....564 ▫ Vehicle Identification Number ... . .564 ▫...
Page 566: Identification Data
564 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake sys- Vehicle Identification Number tems. If either of the two hydraulic systems loses normal The Vehicle Identification Number (VIN) is on the left front capability, the remaining system will still function. How- corner of the instrument panel and is visible from outside ever, there will be some loss of overall braking effective- of the vehicle through the windshield.
Page 567: Torque Specifications
TECHNICAL SPECIFICATIONS 565 Torque Specifications Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. Ensure that the socket is Lug Nut/Bolt **Lug Nut/Bolt Lug Nut/Bolt fully engaged on the lug nut/bolt (do not insert it halfway). Torque Size Socket Size...
Page 568: Fuel Requirements
566 TECHNICAL SPECIFICATIONS cause for concern. However, if the engine is heard making WARNING! (Continued) a heavy knocking sound, see your dealer immediately. Use lowered. Failure to follow this warning may result in of gasoline with an octane number lower than 87 can cause personal injury.
Page 569: Materials Added To Fuel
TECHNICAL SPECIFICATIONS 567 Materials Added To Fuel Gasoline/Oxygenate Blends Besides using unleaded gasoline with the proper octane Some fuel suppliers blend unleaded gasoline with oxygen- rating, gasolines that contain detergents, corrosion and ates such as ethanol. stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, CAUTION! reduce emissions, and maintain vehicle performance.
Page 570: Do Not Use E-85 In Non-Flex Fuel Vehicles
568 TECHNICAL SPECIFICATIONS Do Not Use E-85 In Non-Flex Fuel Vehicles MMT In Gasoline Non-Flex Fuel Vehicles (FFV) are compatible with gasoline Methylcyclopentadienyl Manganese Tricarbonyl (MMT) is containing up to 15% ethanol (E-15). Use of gasoline with a manganese-containing metallic additive that is blended higher ethanol content may void the New Vehicle Limited into some gasoline to increase octane.
Page 571: Carbon Monoxide Warnings
TECHNICAL SPECIFICATIONS 569 Carbon Monoxide Warnings CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition WARNING! malfunctions can cause the catalytic converter to Carbon monoxide (CO) in exhaust gases is deadly. overheat. If you notice a pungent burning odor or Follow the precautions below to prevent carbon mon- some light smoke, your engine may be out of tune or oxide poisoning:...
Page 572: Fluid Capacities
570 TECHNICAL SPECIFICATIONS FLUID CAPACITIES U.S. Metric Fuel (Approximate) 3.6L Engines 19 Gallons 71 Liters Engine Oil With Filter 3.6 Liter Engine (SAE 0W-20 , 5 quarts 4.7 liters API Certified) Cooling System* 3.6 Liter Engine (Mopar Antifreeze/ 13.1 Quarts — 12.4 Liters —...
Page 573: Fluids And Lubricants
TECHNICAL SPECIFICATIONS 571 FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile (240,000 km) Formula OAT (Organic Additive Technology) or equivalent meeting the require- ments of FCA Material Standard MS.90032. Engine Oil –...
Page 574: Chassis
572 TECHNICAL SPECIFICATIONS CAUTION! (Continued) CAUTION! (Continued) rust inhibitors or antirust products, as they may not introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, be compatible with the radiator engine coolant and may plug the radiator.
Page 575 TECHNICAL SPECIFICATIONS 573 Component Fluid, Lubricant, or Genuine Part Refrigerant Use only refrigerant R-1234yf Charge Amounts: Single A/C System — 1.94 lb (880g) Dual A/C System — 2.31 lb (1050g) Compressor Oil Use only PAG oil PSD-1: Single A/C System — 140 ml Dual A/C System —...
Page 577 MULTIMEDIA CONTENTS ▫ Accessing The System From The Uconnect UCONNECT SYSTEMS ....578 System ......634 DRAG &...
Page 578 576 MULTIMEDIA ▫ Uconnect Theater Apps....646 UCONNECT VOICE RECOGNITION QUICK TIPS ....... . .665 ▫...
Page 579 MULTIMEDIA ▫ SiriusXM Travel Link (4C NAV)... . .676 ▫ General Information .....682 ▫...
Page 580: Uconnect Systems
578 MULTIMEDIA UCONNECT SYSTEMS For detailed information about your Uconnect system, refer to your Uconnect Owner’s Manual Supplement. NOTE: Uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. DRAG & DROP MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience.
Page 581: Cybersecurity
MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 582: Uconnect Settings
580 MULTIMEDIA NOTE: UCONNECT SETTINGS • FCA US LLC or your dealer may contact you directly The Uconnect system uses a combination of buttons on the regarding software updates. touchscreen and/or buttons on the faceplate located on the center of the instrument panel that allow you to access and •...
Page 583: Customer Programmable Features
MULTIMEDIA Customer Programmable Features — Uconnect 4 right side of the screen to move up or down through the available settings. Settings gives you to access all of the Settings available programmable features. NOTE: Only one touchscreen area may be selected at a time.
Page 584 582 MULTIMEDIA KeySense After pressing the “KeySense” button on the touchscreen, and entering the KeySense PIN, the following settings will This feature allows you to control specific settings when be available: the KeySense key is in use. The vehicle’s KeySense settings are protected by a unique 4-digit PIN, which the vehicle owner creates when accessing the specific settings for the first time.
Page 585 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Lights Lights & Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, it will alert, visibly and/or audibly, to indicate objects are in your blind spot. The “Blind Spot Alert” feature can be activated in “Lights” mode. When this mode is selected, the Blind Spot Monitor (BSM) system is activated and will only show a visual alert in the exterior mirrors.
Page 586 584 MULTIMEDIA Setting Name Selectable Options Start Up Fuel Level Message Early Low Fuel Alert SiriusXM Setup Channel Skip Subscription Information NOTE: SiriusXM can be programmed to skip channels. To make your selection, press the “Channel Skip” button on the touchscreen, and select the channels you would like to skip.
Page 587 MULTIMEDIA Language After pressing the “Language” button on the touchscreen, the following settings will be available: Setting Name Selectable Options English Français Español Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa- ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped).
Page 588 586 MULTIMEDIA Setting Name Selectable Options Display Brightness With 1-10 1-10 Headlights OFF NOTE: To make changes to the Display Brightness with Headlights OFF setting, the headlights must be off and the interior dimmer switch must not be in the party or parade positions. Set Theme List of Themes NOTE:...
Page 589 MULTIMEDIA Setting Name Selectable Options Navigation Turn-By-Turn In Cluster — If Equipped NOTE: When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in- strument cluster display as the vehicle approaches a designated turn within a programmed route. Ready to Drive Pop-Up —...
Page 590 588 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 591 MULTIMEDIA Setting Name Selectable Options Set Time Minutes NOTE: The “Set Time Minutes” feature will allow you to adjust the minutes. The “Sync time with GPS” button on the touch- screen must be unchecked. Set Time and Format 12 hour 24 hour NOTE: Within the “Set Time and Format”...
Page 592 590 MULTIMEDIA Setting Name Selectable Options Surround View Camera Guidelines NOTE: The “Surround View Rear Back Up Camera Active Guidelines” feature allows you to see active guidelines over the Surround View camera display whenever the gear selector is put into REVERSE or the Surround View button on the touchscreen is pushed.
Page 593 MULTIMEDIA Setting Name Selectable Options ParkView Backup Camera Fixed Guide Lines — If Equipped Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Forward Collision Warn- Warning Only Warning & Braking ing —...
Page 594 592 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- Near ing Sensitivity — If Equipped NOTE: The “Forward Collision Warning Sensitivity” setting determines at what relative distance the vehicle directly in front of you needs to be at, before the system will warn you of a possible collision with the vehicle directly in front of you, based on the option is selected.
Page 595 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Lights Lights and Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Monitor (BSM) system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 596 594 MULTIMEDIA Setting Name Selectable Options Headlight Illumi- 0 sec 30 sec 60 sec 90 sec nated On Approach NOTE: When this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the doors are unlocked with the key fob.
Page 597 MULTIMEDIA Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: NOTE: The auto door lock feature default condition is enabled. When enabled, the door locks will lock automati- cally when the vehicle’s speed exceeds 12 mph (20 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of the customer.
Page 598 596 MULTIMEDIA Setting Name Selectable Options 1st Press of Key Fob Un- Driver locks — If Equipped NOTE: When the “1st Press Of Key Fob Unlocks” feature’s “Driver” option is selected, only the driver’s door will unlock on the first push of the key fob unlock button; you must push the key fob unlock button twice to unlock the passenger’s doors.
Page 599 MULTIMEDIA Setting Name Selectable Options Gate Hands Free Power Sliding Door Personal Settings Linked to Key Fob — If Equipped NOTE: The “Personal Settings Linked to Key Fob” feature provides automatic recall of all settings stored to a memory loca- tion (driver’s seat, exterior mirrors, steering column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle.
Page 600 598 MULTIMEDIA Auto-On Comfort Systems — If Equipped After pressing the “Auto-On Comfort & Remote Start” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 601 MULTIMEDIA Setting Name Selectable Options NOTE: When the “Engine Off Power Delay” feature is selected, the power window switches, radio, Uconnect phone system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to ten minutes after the ignition is cycled to OFF.
Page 602 600 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Equalizer Bass Treble NOTE: When in this display you may adjust the “Bass”, “Mid” and “Treble” settings. Adjust the settings with the “+” and “–”...
Page 603 MULTIMEDIA Setting Name Selectable Options Speed Adjusted Volume Surround Sound — If Equipped Loudness NOTE: This feature improves sound quality at lower volumes when enabled. AUX Volume Offset — If Equipped NOTE: This feature provides the ability to tune the audio level for portable devices connected through the AUX input. AutoPlay NOTE: The “AutoPlay”...
Page 604 602 MULTIMEDIA Compass Settings — If Equipped NOTE: Before compass calibration is performed, the com- pass variance zone should be set for best results. After pressing the “Compass Settings” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Compass Variance NOTE:...
Page 605 MULTIMEDIA Compass Variance Zone Map...
Page 606 604 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Phone Pop-ups Displayed in Cluster Do Not Disturb List of Settings NOTE: The “Do Not Disturb” feature allows the paired phone to send a predetermined call, text, or both, to any incoming call, or text, before sending it directly to voicemail.
Page 607 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Channel Skip List of Channels NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning.
Page 608 606 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Reset App Drawer to Default Order Cancel Restore Settings to Default Cancel NOTE: When the “Restore Settings to Default” feature is selected it resets all settings to their default settings. Clear Personal Data After pressing the “Clear Personal Data”...
Page 609: Customer Programmable Features - Uconnect 4C/4C Nav Settings
MULTIMEDIA Customer Programmable Features — Uconnect Press the “Apps ” button, then press the “Settings ” button on the touchscreen to display the menu 4C/4C NAV Settings setting screen. In this mode the Uconnect system allows you to access all of the available programmable features. NOTE: •...
Page 610 608 MULTIMEDIA KeySense After pressing the “KeySense” button on the touchscreen, and entering the KeySense PIN, the following settings will The vehicle’s KeySense settings are protected by a unique be available: four digit PIN, which the vehicle owner creates when accessing the specific settings for the first time.
Page 611 MULTIMEDIA Setting Name Selectable Options Maximum Vehicle Speed NOTE: The “Maximum Vehicle Speed” feature can be set to 65, 70, 75, 80, or 85 mph (90, 95, 100, 105, 110 km/h). SiriusXM Setup Channel Skip Subscription Information NOTE: SiriusXM can be programmed to skip channels. To make your selection, press the “Channel Skip” button on the touchscreen, select the channels you would like to skip.
Page 612 610 MULTIMEDIA Language After pressing the “Language” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Language List of Languages NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the navigation system (if equipped).
Page 613 MULTIMEDIA Setting Name Selectable Options Display Brightness With Headlights OFF NOTE: To make changes to the Display Brightness with Headlights OFF setting, the headlights must be off and the interior dimmer switch must not be in the party or parade positions. Set Theme NOTE: When the “Set Theme”...
Page 614 612 MULTIMEDIA Setting Name Selectable Options Navigation Turn-By-Turn In Cluster — If Equipped NOTE: When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in- strument cluster display as the vehicle approaches a designated turn within a programmed route. Phone Pop-ups Displayed in Cluster Units...
Page 615 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Never With Help Always Camera After pressing the “Camera” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 616 614 MULTIMEDIA Setting Name Selectable Options Active ParkView Backup Camera Guidelines— If Equipped NOTE: The “Active ParkView Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position when the option is checked.
Page 617 MULTIMEDIA Setting Name Selectable Options Set Time Minutes NOTE: The “Set Time Minutes” feature will allow you to adjust the minutes. The “Sync time with GPS” button on the touch- screen must be unchecked. Time Format 12hrs 24hrs Safety & Driving Assistance After pressing the “Safety &...
Page 618 616 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- Near ing Sensitivity — If Equipped NOTE: The “Forward Collision Warning Plus (FCW+) Sensitivity” setting determines at what relative distance the vehicle directly in front of you needs to be at, before the system will warn you of a possible collision with the vehicle directly in front of you, based on the option is selected.
Page 619 MULTIMEDIA Setting Name Selectable Options LaneSense Warning — If Early Medium Late Equipped NOTE: The “LaneSense Warning” setting determines at what distance the LaneSense system will warn you, through steering wheel feedback, of a possible lane departure. Medium High LaneSense Strength — If Equipped Blind Spot Alert —...
Page 620 618 MULTIMEDIA Mirrors & Wipers After pressing the “Mirror and Wipers” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Rain Sensing Auto Wipers Tilt Side Mirrors in Reverse Headlights with Wipers Brakes After pressing the “Brakes” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 621 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the vehicle is shut off.
Page 622 620 MULTIMEDIA Setting Name Selectable Options Headlights With Wipers — If Equipped Auto Dim High Beams— If Equipped NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights will activate/deactivate automati- cally under certain conditions. Daytime Running Lights Flash Lights With Lock...
Page 623 MULTIMEDIA Doors & Locks The auto door lock feature can be enabled or disabled by your authorized dealer per written request of the customer. After pressing the “Doors & Locks” button on the touch- Please see your authorized dealer for service. screen, the following settings will be available: NOTE: The auto door lock feature default condition is enabled.
Page 624 622 MULTIMEDIA Setting Name Selectable Options 1st Press Of Key Fob Unlocks Driver Door All Doors NOTE: When the “1st Press Of Key Fob Unlocks” feature’s “Driver” option is selected, only the driver’s door will unlock on the first push of the key fob unlock button; you must push the key fob unlock button twice to unlock the passenger’s doors.
Page 625 MULTIMEDIA Setting Name Selectable Options Personal Settings Linked to Key Fob — If Equipped NOTE: The “Personal Settings Linked to Key Fob” feature provides automatic recall of all settings stored to a memory loca- tion (driver’s seat, exterior mirrors, steering column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle.
Page 626 624 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 627 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 628 626 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Phone Pop-ups Displayed in Cluster Do Not Disturb List Of Settings NOTE: Press “Do Not Disturb” to access the available settings. The following settings are: Auto Reply (both, text, call), Auto Reply Message (custom, default) and Custom Auto Reply Message (create message).
Page 629 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start Channel Skip List of Channels NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning.
Page 630 628 MULTIMEDIA Accessibility — If Equipped After pressing the “Accessibility” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Accessibility NOTE: The “Accessibility” feature announces a function prior to performing the action selected when using DVD/Blu-ray and USB Video functions, when it is activated.
Page 631 MULTIMEDIA Setting Name Selectable Options Clear Personal Data Cancel NOTE: When the “Clear Personal Data” feature is selected it will remove all personal data including Bluetooth devices and presets. System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Software License...
Page 632: Steering Wheel Audio Controls
630 MULTIMEDIA STEERING WHEEL AUDIO CONTROLS Left Switch • Pushing the top of the switch will Seek up for the next The remote sound system controls are located on the rear listenable station and pushing the bottom of the switch surface of the steering wheel at the three and nine o’clock will Seek down for the next listenable station.
Page 633: Aux/Usb/Mp3 Control
MULTIMEDIA AUX/USB/MP3 CONTROL The data USB ports are located on the instrument panel below the climate controls. There are numerous USB ports located throughout the vehicle. This feature allows an external USB device to be There are multiple USB “charge only” ports in this vehicle. plugged into the USB port.
Page 634: Uconnect Theater - If Equipped
632 MULTIMEDIA UCONNECT THEATER — IF EQUIPPED Uconnect Theater Overview Your Uconnect Theater is designed to give your family years of enjoyment. There are multiple ways to interact with your Uconnect Theater system. • Play your favorite CDs, DVDs or Blu-ray Discs •...
Page 635: Getting Started
MULTIMEDIA Getting Started There are three different ways to operate the features of the Uconnect Theater: • The Remote Control • The Uconnect System • The Individual Uconnect Theater Touchscreens Uconnect Theater Screen 1 — Uconnect Theater Touchscreen (Rear Touchscreens) 2 —...
Page 636: Accessing The System From The Uconnect System
634 MULTIMEDIA Accessing The System From The Uconnect System Option 2 1. Press the “Apps” button on the bottom of the touch- screen. 2. Press the Uconnect Theater button on the touchscreen. You may need to navigate to different pages in the Apps drawer to find the Uconnect Theater button.
Page 637: Uconnect Theater Controls
MULTIMEDIA Uconnect Theater Controls Parents can control certain features of the system with the “Uconnect Theater Controls” screens, right from the Uconnect touchscreen radio. Options include: • Change media sources or select APPS by using the drop down list • Lock one or both screens •...
Page 638: Accessing The System From The Uconnect Theater Rear Screens
636 MULTIMEDIA • Listen in to a particular Uconnect Theater screen NOTE: A message asking if you would like to pair a through the vehicle’s sound system by selecting the remote will pop up if one has not already been paired to “Listen In”...
Page 639: Pairing The Remote
MULTIMEDIA Pairing The Remote 3. Press the “Remote” button towards the bottom of the Uconnect Theater touchscreen, within the settings menu. 4. Press the “Pair Remote” option. Press the “OK” button. A touchscreen notification will appear indicating that your remote has been paired successfully or unsuccess- fully.
Page 640: Unpairing The Remote
638 MULTIMEDIA Unpairing The Remote Media Sources In events such as updating the Uconnect Theater software, or taking a remote to another vehicle, the remote will need to be unpaired from your Uconnect Theater system. To unpair the remote: 1. Press the Settings icon found in the lower right portion of the Uconnect Theater touchscreen.
Page 641: Uconnect Theater Remote Control
MULTIMEDIA Input” drop down menu. Options include Blu-Ray Disc, 1. Gesture Pad — Control pointer position by running HDMI, USB, Apps, and Viewing the other rear screen. your finger over this area and tapping to select items on the touchscreen, functions similar to a mouse. NOTE: Use the “View Screen”...
Page 642: Uconnect Theater Home Screen And Controls
640 MULTIMEDIA 10. Back Button — Push to exit out of menus or return to Uconnect Theater Home Screen And Controls previous screen. 11. Power Button — Turns the screen for the selected Channel on or off. 12. Screen Indicator — Indicates which screen (1 or 2) is being controlled by the remote control.
Page 643 MULTIMEDIA General Settings To change source card order, select “Source Card Reorder”, then press and hold source card on the touchscreen, and drag and drop in desired order. You can also adjust settings such as: • Brightness • Media port lighting on and off •...
Page 644: General Information
642 MULTIMEDIA General Information Play A DVD/Blu-ray Or USB Media File From Uconnect System The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: 1. Insert a Blu-ray disc or DVD disc into the disc player with the label facing up.
Page 645 MULTIMEDIA 5. To play a DVD/Blu-ray disc on both screens simultane- ously, select disc from both screen drop downs, or choose disc source on one screen and push “View Screen” button on the other. Source Controls From The Uconnect System — Uconnect Theater DVD Blu-ray Disc Player 1 —...
Page 646: Disc Menu
644 MULTIMEDIA 2. Mute Mute rear headphones for selected source for the current ignition cycle. Pressing mute again will unmute rear head- phones. 3. Lock Press to enable/disable Remote Control functions and Rear Touchscreen Controls for the selected source. 4. View Select this button to view full screen video if vehicle is not moving.
Page 647: Blu-Ray Controls - Disc Specific Functions
MULTIMEDIA DOWN, LEFT, and RIGHT arrow buttons, and the OK and MENU buttons on the remote, along with the correspond- ing buttons overlaid on the radio touchscreen, can be used to navigate the disc menu when it appears. This can be used to select specific chapters in a movie, navigate special features, or to play the movie from the menu.
Page 648: Uconnect Theater Apps
646 MULTIMEDIA Uconnect Theater Apps Sudoku App Home Screen Select the Apps source card to play pre-loaded games. Pressing the “Help” button teaches users how to play each Apps Home Screen game. Pick from games: • Back Seat Bingo • Checkers •...
Page 649: Using The Rear Video Usb Port
MULTIMEDIA • Sudoku When a navigation route has been set from the Uconnect system, the second row passengers can use “Are We There • Tic Tac Toe Yet?” for an animated screen showing distance and time NOTE: To exit a game, push “Exit Button” then “Back remaining on navigation routes, as well as the estimated Arrow,”...
Page 650: Play Video Games
648 MULTIMEDIA Plug in a USB drive, iPhone, iPod or mass storage device Play Video Games and play your favorite music or movies. Connect the video game console to the HDMI 1 or 2 ports, located behind the first row seat. NOTE: To view USB media on the rear theater screens, insert a USB drive into the port next to the DVD/Blu-ray disc player.
Page 651: Headphones Operation
MULTIMEDIA Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screens. If no audio is heard after increasing the volume control there are a number of things that can be done to trouble- shoot the issue: •...
Page 652 650 MULTIMEDIA Changing The Audio Mode For Headphones Replacing The Headphone Batteries Each set of headphones requires two AAA batteries for 1. Ensure the remote control and the headphones are on operation. the same channel. To replace the batteries: 2. Push the Home button on the remote control. 1.
Page 653: Display Settings
MULTIMEDIA What Does This Warranty Cover? Except as specified Delphi Automotive reserves the right to replace any dis- below, this warranty covers any Product that in normal use continued Product with a comparable model. THIS WAR- is defective in workmanship or materials. RANTY IS THE SOLE WARRANTY FOR THIS PRODUCT, SETS FORTH YOUR EXCLUSIVE REMEDY REGARDING What Does This Warranty Not Cover? This warranty does...
Page 654: Listening To Audio With The Screen Closed
652 MULTIMEDIA Listening To Audio With The Screen Closed Rear Climate Controls To listen to only audio portion of the channel with the The rear climate controls can also be controlled using the screen closed: Uconnect Theater system. Refer to “Climate Controls” in “Getting To Know Your Vehicle”...
Page 655 MULTIMEDIA Icon Description AUTO Button Automatically controls the rear interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and automatic modes. Refer to “Automatic Operation” in Getting To Know Your Vehicle” for more information. Rear Passenger Temperature Up and Down Buttons Provides the rear passengers with independent temperature control.
Page 656: Accessibility - If Equipped
654 MULTIMEDIA Icon Description Floor Floor Mode Mode Air comes from the floor outlets. Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation. Accessibility —...
Page 657 MULTIMEDIA Choose the Wireless Streaming Source Card on your rear Uconnect Theater touchscreen. Streaming Source On Front Uconnect Touchscreen NOTE: For system compatibility, consult your device’s owner’s manual or www.uconnectphone.com to see if your Wireless Streaming Source Card device supports wireless streaming technology compatibil- The first row passengers can also access wireless streaming ity.
Page 658 656 MULTIMEDIA NOTE: Refer to your device’s user manual or www.ucon- NOTE: The Authentication Screen will appear on both rear nectphone.com for further information. touchscreens. The touchscreen screen on which “Accept” is selected will be the primary controller for the wireless 3.
Page 659: Bd And Dvd Region Codes
MULTIMEDIA BD And DVD Region Codes Many BD and DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the BD or DVD disc does not match the region code for the Blu-ray Disc player, the disc will not play.
Page 660 658 MULTIMEDIA • For multi-session CDs that contain only multiple CD- Compressed Audio Files (MP3, WMA and AAC) Audio sessions, the player will renumber the tracks so The Blu-ray Disc player is capable of playing MP3 each track number is unique. (MPEG-1 Audio Layer 3), WMA (Windows Media Audio) •...
Page 661 MULTIMEDIA • Other compression formats such as MP3 Pro, Ogg Disc Errors Vorbis, and ATRAC3 will not play. The Blu-ray player If the Blu-ray Disc player is unable to read the disc, a Disc will automatically skip the file and begin playing the Error message is displayed on the rear screen and Radio next available file.
Page 662: Product Agreement
660 MULTIMEDIA Product Agreement Please refer the contract details which are disclosed in the following websites, for example, concerning these above Open Source Software software. http://www.gnu.org/licenses/old-licenses/gpl- The software built into this product, are composed of 2.0-standalone.html, http://www.gnu.org/licenses/lgpl- multiple software components, and there are the copy- 2.1-standalone.html, http://www.freetype.org/FTL.TXT.
Page 663 MULTIMEDIA Dolby BD-J Manufactured under license from Dolby Laboratories. Java is a registered trademark of Oracle and/or its affili- Dolby and the double-D symbol are trademarks of Dolby ates. Laboratories. MPEG THIS PRODUCT IS LICENSED UNDER THE AVC PAT- For DTS patents, see http://dts.com/patents. Manufac- ENT PORTFOLIO LICENSE FOR THE PERSONAL AND tured under license from DTS Licensing Limited.
Page 664: General Information
662 MULTIMEDIA DivX VOD section of your device setup menu. DivX, DivX CAUTION! Certified and associated logos are trademarks of DivX, LLC and are used under license. Use of controls or adjustments or performance of procedures other than those specified herein may re- Cinavia sult in hazardous radiation exposure.
Page 665: Fcc/Ic Regulatory Notices
MULTIMEDIA FCC/IC Regulatory Notices the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a Modification Statement residential installation. This equipment generates, uses and Any changes or modifications not expressly approved by can radiate radio frequency energy and, if not installed and the party responsible for compliance could void the user’s used in accordance with the instructions, may cause harm- authority to operate this equipment.
Page 666: Radio Operation And Mobile Phones
664 MULTIMEDIA RADIO OPERATION AND MOBILE PHONES The radio manufacturer believes the internal wireless radio is safe for use by consumers. The level of energy emitted is Under certain conditions, the mobile phone being on in far less than the electromagnetic energy emitted by wire- your vehicle can cause erratic or noisy performance from less devices such as mobile phones.
Page 667: Tips
MULTIMEDIA NOTE: UCONNECT VOICE RECOGNITION QUICK TIPS • This equipment has been tested and found to comply Introducing Uconnect with the limits for a Class B digital device, pursuant to Start using Uconnect Voice Recognition with these helpful Part 15 of the FCC Rules. These limits are designed to quick tips.
Page 668: Get Started
666 MULTIMEDIA Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. Helpful hints for using Voice Recognition: 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions.
Page 669: Basic Voice Commands
MULTIMEDIA Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say: • “ Cancel” to stop a current voice session • “ Help” to hear a list of suggested Voice Commands •...
Page 670: Radio
668 MULTIMEDIA Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say: •...
Page 671: Media
MULTIMEDIA • “ Change source to Bluetooth” • “ Change source to AUX” • “ Change source to USB” • “ Play artist Beethoven”; “ Play album Greatest Hits”; “ Play song Moonlight Sonata”; “ Play genre Classical” TIP: Press the Browse button on the touchscreen to see all of the music on your USB device.
Page 672: Phone
670 MULTIMEDIA • “ Call John Smith” • “ Dial 123-456-7890 and follow the system prompts” • “ Redial (call previous outgoing phone number)” • “ Call back (call previous incoming phone number)” TIP: When providing a Voice Command, push the Phone button and say “...
Page 673: Voice Text Reply
MULTIMEDIA 2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without I’ll be late. Okay. Where are you? I will be <number>...
Page 674: Climate
672 MULTIMEDIA Apple iPhone iOS 6 or later supports reading incoming Climate text messages only. To enable this feature on your Apple Too hot? Too cold? Adjust vehicle temperatures hands-free iPhone, follow these four simple steps: and keep everyone comfortable while you keep moving ahead.
Page 675: Navigation (4C Nav)
Uconnect 4 Climate 1. To enter a destination, push the VR button . After the beep, say: “ Find address 800 Chrysler Drive Auburn Hills, Michigan.”...
Page 676: If Equipped
674 MULTIMEDIA 2. Then follow the system prompts. SiriusXM Guardian (4C/4C NAV)— If Equipped TIP: To start a POI search, push the VR button . After CAUTION! the beep, say: “ Find nearest coffee shop.” Some SiriusXM Guardian services, including SOS Call and Roadside Assistance Call will NOT work without an operable LTE (voice/data) or 3G or 4G (data) net- work connection compatible with your device.
Page 677: Register (4C/4C Nav)
MULTIMEDIA Send & Go 2. Select the Activate Services icon from your list of apps. Vehicle Finder 3. Select “Customer Care” to speak with a SiriusXM Guardian Customer Care agent who will activate ser- Stolen Vehicle Assistance vices in your vehicle, or select “Enter Email” to activate Remote Vehicle Start** on the web.
Page 678: Mobile App (4C/4C Nav)
676 MULTIMEDIA • Once on the “Remote” screen, you can begin using Mobile App (4C/4C NAV) Remote Door Lock/Unlock, Remote Vehicle Start, and You’re only a few steps away from using remote com- activate your horn and lights remotely, if equipped. mands and sending a destination from your phone to your •...
Page 679: Siri Eyes Free - If Equipped
MULTIMEDIA TIP: Traffic alerts are not accessible with Voice Command. designed to keep your eyes on the road and your hands on the wheel by letting Siri help you perform useful tasks. To enable Siri, push and hold, then release the Uconnect Voice Recognition (VR) button on the steering wheel.
Page 680: Using Do Not Disturb
678 MULTIMEDIA there is a counter display to keep track of your missed calls and text messages while you were using Do Not Disturb. Do Not Disturb can automatically reply with a text mes- sage, a call or both, when declining an incoming call and send it to voicemail.
Page 681: Android Auto - If Equipped
MULTIMEDIA Android Auto — If Equipped Android Auto allows you to use your voice to interact with Android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project your Android powered smart- phone and a number of its apps onto your Uconnect touchscreen.
Page 682: Apple Carplay - If Equipped
680 MULTIMEDIA Apple CarPlay — If Equipped Apple CarPlay allows you to use your voice to interact with Siri through your vehicle’s voice recognition system, and use your smartphone’s data plan to project your iPhone and a number of its apps onto your Uconnect touchscreen.
Page 683 MULTIMEDIA Apple CarPlay On 7-inch Display Apple CarPlay On 8.4-inch Display Refer to your Uconnect Owner’s Manual Supplement for further information.
Page 684 682 MULTIMEDIA General Information Additional Information The following regulatory statement applies to all Radio © 2017 FCA US LLC. All rights reserved. Mopar and Frequency (RF) devices equipped in this vehicle: Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a This device complies with Part 15 of the FCC Rules and trademark of Google Inc.
Page 685 MULTIMEDIA CD/DVD DISC MAINTENANCE 5. Store the disc in its case after playing. To keep a CD/DVD in good condition, take the following 6. Do not expose the disc to direct sunlight. precautions: 7. Do not store the disc where temperatures may become 1.
Page 687 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......686 Impaired (TDD/TTY) .
Page 688: Suggestions For Obtaining Service For Your Vehicle
686 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 689: Fca Us Llc Customer Center
Outside Mexico City: 1-800-505-1300 • Vehicle delivery date and mileage Puerto Rico And U.S. Virgin Islands FCA US LLC Customer Center Customer Service Chrysler International Services LLC P.O. Box 21–8004 P.O. Box 191857 Auburn Hills, MI 48321–8004 San Juan 00919-1857 Phone: (800) 247-9753 Tel.: (888) 242-6342...
Page 690: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
688 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech and an Owner Identification Card in the mail within three Impaired (TDD/TTY) weeks of the vehicle delivery date. If you have any questions about the service contract, call the manufactur- To assist customers who have hearing difficulties, the er’s Service Contract National Customer Hotline at 1-800- manufacturer has installed special TDD (Telecommunica-...
Page 691: Warranty Information
CUSTOMER ASSISTANCE 689 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 692: In Canada
690 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 693 INDEX...
Page 694 692 INDEX About Your Brakes ......564 Air Conditioner Maintenance ....514 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 695 INDEX 693 Adding Fluid ......532, 572 Brake System ......529, 564 Fluid And Filter Changes .
Page 696 694 INDEX Car Washes.......558 Climate Control......105 Cellular Phone .
Page 697 INDEX 695 Cruise Light ......210, 212 Driving Customer Assistance ......686 Through Flowing, Rising, Or Shallow Standing Customer Programmable Features .
Page 698 696 INDEX Checking Oil Level ..... . .508 Filters Compartment ......507 Air Cleaner .
Page 699 INDEX 697 Fuel ........566 Hazard Additives .
Page 700 698 INDEX Hook, Coat .......170 Key Fob Battery Service (Remote Keyless Entry) ..23 Keyless Enter-N-Go Inside Rearview Mirror .
Page 701 INDEX 699 Bulb Replacement .....443, 447 Security Alarm ......205 Center Mounted Stop .
Page 702 700 INDEX Manual, Service......690 Occupant Restraints ......244 Map/Reading Lights .
Page 703 INDEX 701 Owner’s Manual (Operator Manual) ...4, 690 Radiator Cap (Coolant Pressure Cap)... . .527 Radio Frequency Paint Care....... .557 General Information .
Page 704 702 INDEX Programming Additional Key Fobs ... . .32 Seat Belt Remote Battery Replacement ....23 Adjustable Upper Shoulder Belt Anchorage .
Page 705 INDEX 703 Untwisting Procedure .....250 Service Manuals ......690 Seats .
Page 706 704 INDEX Engine Fails To Start ..... .318 Tilt Steering Column ......87 Remote .
Page 707 INDEX 705 Spare Tire ..... . .460, 549, 551 Trailer Towing Guide ......422 Spinning .
Page 708 706 INDEX Universal Transmitter......157 Water Unleaded Gasoline ......566 Driving Through .
Page 715 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Chrysler Pacifica 2018 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Quick Links

Chapters

Related Manuals for Chrysler Pacifica 2018

Summary of Contents for Chrysler Pacifica 2018