Operating Time; Using The Appliance; Trimming With Comb - Philips QP6510 User Manual

- When the appliance is charging, first the bottom
light flashes white and then lights up white
continuously (Fig. 6). Then the second light
flashes and then lights up continuously, and so
on until the appliance is fully charged.
- Quick charge: after approx. 5 minutes charging,
the appliance contains enough energy for 5
minutes using. During quick charge the lights of
the battery status indicator will light up
continuously one after another and then all
switch off. This will repeat itself until quick
charge is finished.
- When the battery is fully charged, all lights of
the battery status indicator light up
continuously.
Note: After approx. 30 minutes, the light goes
out automatically.
Charging with the supply unit
1 Insert the small plug into the appliance and put
the supply unit in the wall socket (Fig. 7).
2 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.

Operating time

A fully charged appliance has an operating time of
up to 60 minutes.

Using the appliance

You can use the appliance to trim, edge or shave
facial hair (beard, moustache and sideburns).
Shave for a smooth result, trim to obtain a certain
length and edge to create perfect edges and sharp
lines. Take your time when you first start to use the
appliance. You have to acquire practice with the
appliance.
This appliance is for use on facial hair. This
appliance is not intended for shaving, edging or
trimming hairs on lower body parts or scalp hair.
Always check the appliance before you use it. Do
not use the appliance or any other part if it is
damaged, as this may cause injury. Always
replace a damaged part with one of the original
type.
Note: This appliance can only be used without
cord (Fig. 4).
Switching the appliance on and off
1 To switch the appliance on or off, press the
on/off button once (Fig. 8).
Shaving
Before you use the appliance, always check
the blade for damage or wear. If the blade is
damaged or worn, do not use the appliance,
as injury may occur. Replace a damaged blade
before you use the appliance (see chapter
'Replacement').
- Make sure that the blade is in full contact with
the skin by placing it flat on the skin.
- For the best result, move the appliance against
the grain.
- Make long strokes while pressing lightly.
- You can use the appliance dry or wet with gel
or foam, even in the shower.
- Shaving a clean beard and face gives the best
results.
1 Switch on the appliance (Fig. 8).
2 Place the blade on the skin and move the
appliance up or against the grain in long strokes
while pressing lightly (Fig. 9).
Note: Make sure you hold the surface of the
blade flat against your skin (Fig. 10).
3 Switch off and clean the appliance after every
use (see 'Cleaning and maintenance').
Edging
- You can also use both edges of the blade to
create sharp lines and perfect edges.
- Hold the appliance in such a way that the blade
is perpendicular to the skin and one of its edges
touches the skin. This allows more precise
detailing of sideburns and the area around the
mouth and nose.
1 To use the blade for creating sharp edges and
lines, use either edge of the blade (Fig. 11).
2 Switch on the appliance (Fig. 8).
3 Place the edge of the blade perpendicular onto
the skin (Fig. 12).
4 Make straight strokes while applying gentle
pressure (Fig. 13).
5 Switch off and clean the appliance after every
use (see 'Cleaning and maintenance').

Trimming with comb

- The precision trimming comb allows you to trim
hair to different lengths. Start at the highest
setting to acquire practice with this appliance.
- The settings on the wheel correspond to the
remaining hair lengths after trimming, in
millimeters. You can select a length from 0.5mm
(1/32 in.) to 10mm (13/32 in.).
- Always trim in the direction of the teeth of the
precision trimming comb making sure the flat
part of the comb is in full contact with the skin
for an even trimming result (Fig. 14).
- Since hair grows in different directions, you
need to hold the appliance in different
positions as well. However, always make sure
that you move the appliance upwards against
the grain.
- Trimming is easier when the skin and hair are
dry.
1 Place the front part of the comb onto the blade
and push the projection at the back of the
comb into the appliance ('click') (Fig. 15).
2 Turn the hair length setting wheel to select the
desired hair length setting (Fig. 16).
The settings on the wheel correspond to the
hair lengths in millimeters (Fig. 17).
3 Switch on the appliance (Fig. 8).
4 Place the comb onto the skin and move the
appliance upwards slowly, against the grain
(Fig. 18).