Summary of Contents for Pyle Hydra PLMR440PA
- Page 1 PYLE® HYDRA PLMR440PA Marine Public Address System Controller Remote Control Included OWNER'S MANUAL...
- Page 2 • Remote Subwoofer Control • Signal-to-Noise Ratio: BetlerThan 102 dB • Dimensions (W x D x H): 12-3/4" x 7-3/8" x 2-1/4" (324 x 187 x 57 mm) Owner's 1-PLMR44QPA Manual PYLE PLMR440PA Marine Public Address PYLE your choice for marine audio entertainment!
-
Page 3: What Is Included
Introduction An important member of the pleased to introduce the unique PLMR440PA, a powerful amplifier with public address capabilities. PYLE This marine models features both high pass and low pass crossovers. For further flexibility in the use of a subwoofer, a variable bass boost control has been included. -
Page 4: Installation Precautions
Do not adjust this Input level to maximum unless your Input level requires It. Ignoring these instructions will result in an input overload to the amplifier, and excessive audio distortion. It can also cause the protection circuit to engage. 3-PLMR440PA Owner's Manual... -
Page 5: Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same timel 4-Channel Amplifier PLMR440PA $Ubwo~o.r Remote level control 4-Channel Amplifier PLMR440PA rr==~=-'O r~rl~~:-=.i··~~;;~=.ioi~~~"'~~~~~c=.i~~~7~=_... -
Page 6: High Level Input Wiring
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same timel 4-Channel Amplifier PLMR440PA with 4-Channel Audio Input Soun:e -m -- -- --rn I--~~~-- RE'®\'... - Page 7 2-Channel Audio Input Source SUbwoo~er Remote level control Input Mode switch in 2CH Position To LEFT head unft or signal LOW LEVEL INPUTS in Ihis used installation HIGH LEVEL CH3I41NPUTS UNcI inslalllllion ..RIGHT Tennlnals Speakar proc:eesor 6-PLMR440PA Owner's Manual...
- Page 8 Microphone Input Wiring If you wish to use the public address feature in the PLMR440PA, all you need to do is to connect the custom microphone included with the amp. When you press the button on the microphone, it automatically cuts off the input to Channels 1-4 from your audio source and presents the microphone signal to the amplifier.
- Page 9 4 Channel Mode Four Channel Mode """'" CONNECnONS ORANGE term",,1 FUSE (provided) PYLE" H""RA PLMR440PA. RlURCIWINELI'CIWER"'-"'_ PIIKJCADIIIIEIISa'IalEM Chassis ground point REMOTE TURN-()N head Battery WHITE Speaker GREY Speaker GREY/BLACK GREEN Spoakor GREEN BLACK PIJRPI..E Speaker PURPLE I BLACK 8-PLMR440PA Owner's Manual...
-
Page 10: Power And Speaker Wiring
Power and Speaker Wiring Bridged Mode Bridged Mode P<ME. CONNEcnONS Chassis ground point ORANGE IenTinai FUSE (provided) g..PLMR440PA Owner's Manual """'''''' PYLE" HYDRA PLMR440M _"='m"=~ER ID REMOlE lURN'()N head Battery PURPLE I BLACK ...,. Connect the CH1J+) Isad the Subwoofer 1 (+) tarmine/. -
Page 11: Speaker Wiring
&dB Passive Crossover FREQUENCY INDUCTOR CAPACITOR 470uF 7.5mH 80Hz 330uF 5.SmH 100Hz 330uF 5.5mH 120Hz 220uF 150Hz PYLE" HVClIIIIA PLIIII440PA FOU'l.u~'1il"o"=~F1E1t ci head Batteryl l ~=~'IICH3 l~=:;;;~~~CII • ..-..Speaker -... Speaker 1Q-PLMR440PA Owner's Manual... -
Page 12: Troubleshooting
Troubleshooting Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. Amplifier will not power up. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the +terminal.