CONTENTS Installation...3 Take out screw before installation ...3 DIN Front-Mount (Method A)...3 Installing the unit ...3 Removing the unit ...4 DIN Rear-Mount (Method B)...5 Wiring Connection...6 Operation...7 Location of keys ...7 Switching on/off the unit ...8 Sound adjustment ...8 Loudness ...8 Equalization ...8 Subwoofer ...8 Display ...8...
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal function of the driver. • Before installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the system works properly.
INSTALLATION Sleeve L Key Outer Trim Ring Front Panel R Key 5. Mount the sleeve by inserting it into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective.
INSTALLATION DIN REAR-MOUNT (Method B) If your vehicle is a Nissan or Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.
WIRING CONNECTION ANTENNA CONNECTOR FUSE IGNITION SWITCH (ACC+) FUSE MEMORY YELLOW BACK-UP (B+) BLACK GROUND (B–) POWER BLUE ANTENNA WHITE FRONT Lch SPEAKER WHITE/BLACK GREEN REAR Lch SPEAKER GREEN/BLACK MAIN UNIT SUBWOOFER CABLE (GREEN) RCA CABLE GREY GREY/BLACK VIOLET VIOLET/BLACK (GREY) Rch RED Lch WHITE...
OPERATION GENERAL OPERATION • SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except EJECT button (7)). When system is on, press button (1) to turn off the unit. • SOUND ADJUSTMENT Press SEL button (2) shortly to select the desired adjustment mode.
OPERATION RADIO OPERATION • SWITCHING TO RADIO MODE Press MOD button (12) momentarily to select radio mode, the radio mode appears in the display together with the memory band and frequency. • SELECTING THE FREQUENCY BAND In radio mode, press BND/LOU (ENT) button (11) momentarily to select the desired band.
OPERATION CD OPERATION • SWITCHING TO CD MODE If there is no CD inserted in the driver: Gently insert the CD with the printed side up into the CD compartment until you feel some resistance. The CD is drawn into the driver automatically. CD playback begins.
Page 11
OPERATION • SELECTING TRACKS BY AS/PS/D- AUD BUTTON AS/PS (D-AUD) button is assigned as Digital Audio Mode selection button in MP3 operation. When pressed, it selects each mode of Digital Audio. “Searching track directly” => “Searching Directory or File Name”=> “Navigation”...
OPERATION • DISPLAY INFORMATION Press DSP button (20) to show following information, such as the clock, ID3 TAG (if available: song title, directory name, artist name and other contents…) and other information. KEY Assigned IN Searching mode (Table 1) AS/PS Mode Select BND/LOU ENTER...
OPERATION SUPPORTED MP3/WMA DECODING MODES The main unit supports MP3/WMA (Windows Media Audio) decoding modes as below. Standard Bit Rate (kbps) MPEG1 Audio 32, 48, 64, 96, Layer 3 128, 192, 256, (44.1kHz) Windows 64, 96, 128, Media Audio (44.1kHz) The USB solution can support: 1.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity (S/N = 30 dB) Stereo Separation Frequency Coverage Sensitivity (S/N = 20 dB)
TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. The car ignition switch is not on. The fuse is blown. Disc cannot be Presence of CD disc inside loaded or ejected.