Emptying The Clear Bin; Washing Your Filter - Dyson DC20 Operating Manual

USING YOUR DYSON VACUUM CLEANER
PLEASE NOTE:
• Always extend the cable fully to the red tape before use.
• Fine dust such as plaster or flour should only be vacuumed in very
small amounts.
• Do not use the vacuum cleaner to pick up sharp hard objects, such as small toys,
pins, paper clips etc.
• If used in a garage, care should be taken to wipe the soleplate and wheels with
a dry cloth after vacuuming to clean off any sand, dirt, or pebbles which could
damage delicate floors.
• When vacuuming, certain carpets may generate small static charges in the clear
bin. These are entirely harmless and not associated with the mains supply. To
minimise any effect from this, do not put your hand or insert any object into the
clear bin unless you have emptied it and rinsed it out with cold water.
• Only use parts recommended by Dyson; failure to do so could invalidate
your guarantee.
• Do not use any lubricants, cleaning agents, polishes or air fresheners on any
part of the vacuum cleaner.
• This vacuum cleaner is fitted with a thermal cut-out. If any part of the vacuum
cleaner becomes blocked the machine may overheat and automatically shut
'OFF'. If this happens, switch 'OFF' and unplug the vacuum cleaner and allow to
cool before attempting to check the filter or for blockages. Clear any blockages
before restarting.
• Store the vacuum cleaner indoors. Do not use or store this vacuum cleaner
below 0°C. Ensure that the vacuum cleaner is at room temperature before
operating.

EMPTYING THE CLEAR bIN

CAUTION:
• Switch 'OFF' the vacuum cleaner and unplug before emptying the clear bin.
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• To remove the clear bin from the vacuum cleaner, press the silver button at
the rear of cyclone carrying handle. To release the dirt, press the silver button on
the front of the clear bin and separate the cyclone unit from the clear bin.
• To minimise dust/allergen contact when emptying, encase the clear bin tightly
in a plastic bag and empty. Remove the clear bin carefully and seal bag tightly,
dispose as normal. Emptying into a bag is recommended for people with
asthma and allergies.
• Do not use the vacuum cleaner without the clear bin in place.
CLEANING THE CLEAR bIN
CAUTION:
• To remove the cyclone unit from the clear bin press the silver button on the front
of the clear bin and separate the cyclone unit from the clear bin.
• Clean the clear bin with cold water only.
• Ensure the clear bin is completely dry before replacing.
PLEASE NOTE:
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Clean the shroud with a cloth or dry brush to remove lint and dust.

WASHING YOUR FILTER

DO THIS EVERY 6 MONTHS
CAUTION:
• Switch 'OFF' and unplug the vacuum cleaner before removing the filter.
• Ensure the filter is completely dry before refitting to the vacuum cleaner.
PLEASE NOTE:
This machine has one filter, located as shown. It is important to check your
filter regularly and wash at least every 6 months according to instructions, to
maintain performance.
• After washing please leave for 24 hours to dry completely.
• The filter may require more frequent washing if vacuuming fine dust.
• Do not use detergents to clean the filter.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
• Register for a filter wash reminder by email (Australia only);
aucustomercare@dyson.com
8
LOOKING FOR bLOCKAGES
CAUTION:
• Switch 'OFF' and unplug the vacuum cleaner before checking for blockages.
• Beware of sharp objects when clearing blockages.
• Refit all parts of the vacuum cleaner securely before using.
PLEASE NOTE:
• Clearing blockages is not covered by your vacuum cleaner's limited guarantee.
If any part of your vacuum cleaner becomes blocked, it may overheat and then
automatically shut 'OFF'. Unplug the vacuum cleaner and leave to cool down.
Clear blockage before restarting.
• Large items may block the tools or wand inlet, if this happens switch the vacuum
cleaner 'OFF' and unplug the vacuum cleaner before removing the blockage.
Do not operate the wand release catch.
1
2
3