Page 1
SMT Series Hot Water - Electric Start - Diesel Pressure Washer Trailer Service Manual MODEL: SMT-354037E 1.103-841.0 WARNING: This product and accessories may contain a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.
AVERTISSEMENT: Ce manuel de l'utilisateur contient des informations en matière de sécurité et des instructions pour la remorque. Lire le présent manuel avant de charger ou de remorquer la remorque. Suivre toutes les précautions de sécurité et les directives. Shark SMT Operator’s Manual 9.800-504.0 - E...
10. Always wear properly rated eye protection such as flamme nue ou d'une torche est permise. safety goggles or face shield while spraying. (Safety glasses do not provide full protection.) Shark SMT Operator’s Manual 9.800-504.0 - E...
Page 5
This machine must be attended during cause malfunction of the machine operation. and result in death, serious bodily injury, and/or property damage. Follow storage instructions specified in this manual. Shark SMT Operator’s Manual 9.800-504.0 - E...
• Wheel lugs* water and no hotter then 90°F. • Bearing lube and tightness • Hitch • Safety chains • 12V running lights • Distribution and security • Caster up in travel position Shark SMT Operator’s Manual 9.800-504.0 - E...
Both the tire placard and the VIN label are permanently attached on top of the frame of your trailer and have the required information printed on them. They also list the maximum load that can be placed on the trailer without Shark SMT Operator’s Manual 9.800-504.0 - E...
Page 8
Also read the information supplied with your tow vehicle so you know and understand it's limitations. Shark SMT Operator’s Manual 9.800-504.0 - E...
If the 5,000# GVWR 2” connection was not properly made, the ball and socket will separate as the tongue of the trailer is raised. 8,000# GVWR 2” Shark SMT Operator’s Manual 9.800-504.0 - E...
GVWR of the trailer less the empty weight of the trailer because there may be another controlling factor such as frame strength that reduces Bottom View the carrying capacity to what is listed on the VIN tag. Shark SMT Operator’s Manual 9.800-504.0 - E...
NIV et/ou le flanc du pneu. Agir de la sorte risquerait de causer une défaillance d'une ou plusieurs composantes de la remorque, causant Shark SMT Operator’s Manual 9.800-504.0 - E...
STEP 1: Release the quick release pin by rotating it wise. Reverse step to lower caster. clock wise. Pull Quick release pin from receptacle. NOTE: Before towing, diesel shut-off valve must be in Rotate the caster clockwise. the OFF position. Shark SMT Operator’s Manual 9.800-504.0 - E...
ATTENTION: Ce frein comprend un mécanisme à ressort qui retournera le frein à sa position de désengagement. Garder les pieds et les mains à l'écart de la zone du point de pincement. Shark SMT Operator’s Manual 9.800-504.0 - E...
The pin can be engaged fully only if ball is properly seated in the coupler. Avoid sudden Wheel Flat stops when lockup & tire Spots possible and skidding adjust brakes. Shark SMT Operator’s Manual 9.800-504.0 - E...
This system prevents internal Wand — Must be connected to the spray gun. pump damage. High Pressure Hose — Connect one end to water pump high pressure discharge nipple and the other end to spray gun. Shark SMT Operator’s Manual 9.800-504.0 - E...
(See Hose Box and Fuel Tank pages for NOTE: Fastener assembly torque to install handle:10 fastener part numbers.) ft-lbs (due to hollow tube handle.) Shark SMT Operator’s Manual 9.800-504.0 - E...
Débrancher la borne de mise à la moment de remplir les réservoirs. terre de la batterie avant de NOTE: Diesel Fuel Shut-off must procéder à des opérations d'entre- be in the ON position prior to tien. turning on burner. Shark SMT Operator’s Manual 9.800-504.0 - E...
Trigger Safety Latch High Pressure Hose NOTE: High pressure nozzle must be inserted at end of wand to obtain high pressure. To apply detergent, read operator's manual. Shark SMT Operator’s Manual 9.800-504.0 - E...
NOTE: Detergent cannot be applied using Red, Yellow, • Produits à base de tripolyphosphate de sodium Green or White nozzles. • Ammoniac ou produits à base d'acide These chemicals will harm the machine and will damage the surface being cleaned. Shark SMT Operator’s Manual 9.800-504.0 - E...
STEP 5: Lock trigger gun safety STEP 4: Turn garden hose water lever to prevent unintentional off. Open the spray gun to relieve pulling of trigger. remaining pressure. Shark SMT Operator’s Manual 9.800-504.0 - E...
CAUTION: Failure to follow the above directions will result in damage to your pressure washer. ATTENTION: Le non-respect des directives ci- dessus entraînera des dommages à la laveuse à pression. Shark SMT Operator’s Manual 9.800-504.0 - E...
In areas where alkaline water is an extreme problem, periodic use of descale powder will remove lime and other deposits before coil becomes plugged. Shark SMT Operator’s Manual 9.800-504.0 - E...
.air band may need spray gun. to be decreased. For higher humidity, the air band opening may need to be increased; for lower relative humidity, the .air band may need to be decreased. Shark SMT Operator’s Manual 9.800-504.0 - E...
Do not settings. Check with your dealer before making local throttle down the engine for any length of time. site fuel pressure adjustments. Shark SMT Operator’s Manual 9.800-504.0 - E...
5. Reinstall the hub, reversing the procedure above using the bearing adjustment procedures below. 6. If you have the Posi–Lube system refer to the “Posi-Lube Lubrication Procedure”. Shark SMT Operator’s Manual 9.800-504.0 - E...
When you begin to see the new grease, remove the gun and clean off any excess and replace the rubber cap. Shark SMT Operator’s Manual 9.800-504.0 - E...
Broken or weak inlet or discharge PUMP Check and replace if necessary. valve springs NOISY Excessive matter in valves Check and clean if necessary. Worn bearings Check and replace if necessary. Shark SMT Operator’s Manual 9.800-504.0 - E...
Page 29
200) and smokes when burner is off NOTE: For additional service information for the engine, refer to the engine Operation and Maintenance Manual included with pressure washers. Shark SMT Operator’s Manual 9.800-504.0 - E...
Every 6 months Replace Quick Connects Annually Clean Water Screen/Filter Weekly Replace HP Hose Annually For additional service information for the engine, refer to the engine Operation and Maintenance Manual included with pressure washers. Shark SMT Operator’s Manual 9.800-504.0 - E...
Inspect for cuts, wear, Tire Conditions bulging, etc. Pump And Engine Oil Change Record Estimated Operating Estimated Operating Date Oil Changed Date Oil Changed Hours Since Last Oil Hours Since Last Oil Month/Day/Year Month/Day/Year Change Change Shark SMT Operator’s Manual 9.800-504.0 - E...
Page 32
9.800-504.0 - Printed in U.S.A. or Mexico...