Summary of Contents for ESI EWT90
- Page 1 Concrete Finishers Range EWT90 EWT120 Operator’s Manual Manual Version 1 Concrete Finisher...
- Page 2 Concrete Finisher Proposition Warning...
-
Page 3: Ec Declaration Of Conformity
Nous soussignons, 101 Gannaway Drive Suite #3 PO Box 997 Jamestown, NC 27282 USA, certifions que si le produit décrit dans ce certificat est acheté chez un distributeur de la marque déposée “ESI” au sein de la EEA, celui-ci est conforme aux norms CEE ci-après: Norme de la machine 2006/42/CE, Norme compatible pour l’électromagnétisme 2004/108/CE (modifie par... - Page 4 This manual has been written to help you operate your concrete finisher safely. It is intended primarily for dealers and operators of ESI concrete finishers. It is recommended that you keep this manual or a copy of it with the machine, so that it is readily available for reference.
-
Page 5: Safety Information
If you are unsure about the safe and correct use of the concrete finisher, consult your supervisor or ESI. Improper maintenance can be hazardous. Read and understand this section before you perform any maintenance, service or repairs. - Page 6 sometimes necessary that the manufacturer must be informed of such an event for future countermeasures. Fuel Safety Fuel is flammable. It may cause injury and property damage. Shut down the engine, extinguish all open flames and do not smoke while filling the fuel tank. Always wipe up any spilled fuel.
-
Page 7: Environment
Concrete Finisher Manual (Version 1) Environment In order to protect the environment please Component Material recycle discarded apparatus Operator Handle Steel accessories. The table beside provides Belt Guard Glass Fiber with list machine’s Blade Guard Steel components and their respective materials. Bedplate Steel Take the discarded apparatus to the... -
Page 8: Machine Description
Machine Description EWT90 1. Throttle Lever 2. Pitch Control Lever 3. Cutout Switch Handle 4. Exhaust Guard 5. Air Filter 6. Fuel Tank 7. Recoil Starter 8. Blade Guard 9. Belt Guard 10. Handle Height Adjuster 11. Lifting Bar EWT120 1. -
Page 9: Pre-Start Checks
Concrete Finisher Manual (Version 1) Pre-Start Checks The following pre-start inspection must be performed before the start of each work session. Please refer to the service & maintenance section for detailed guidance. If any fault is discovered, the concrete finisher must not be used until the fault is rectified. Thoroughly inspect the machine for signs of damage. -
Page 10: Operation
1. Verify the correct blades for the job have been chosen and that they are properly installed. Inspect the blades carefully for damage. Never use any questionable blades. 2. Check to be sure the blades are free of obstructions and the area is clear for operation. 3. - Page 11 The blades of the concrete finisher spin in a clockwise direction. All ESI concrete finisher are directed left or right by applying a slight upward (lifting) or downward (lowering) pressure on the handle (respectively).
-
Page 12: Operation
paste collected during the floating operation. Increase the blade pitch up to 10mm for the first finishing operation and then continue to increase the pitch on the following finishing operations. Continue the finishing passes until you obtained the desired finished floor surface. The time required between each finishing pass is dependent on the weather conditions, cement and water content of the concrete. -
Page 13: Service And Maintenance
CAUTION Maintenance The ESI concrete finisher is designed to give many years of trouble-free operation. It is, however, important that the simple regular maintenance listed in this section is carried out. It is recommended that an approved ESI dealer carry out all major maintenance and repairs. Always use genuine ESI replacement parts, the use of non-genuine ESI parts may void your warranty. - Page 14 Unleaded GX100 0.4 [.4] 0.77 [.8] Petrol / 10W-30 GX160 Gasoline 2.5 [2.6] EWT90 EP90 (0.35) [.37] Gearbox 90 Weight EWT120 (0.6) [.6] Note: • Check the gearbox oil at regular intervals and top-up when necessary. Make sure the oil is at the centre of the sight glass.
-
Page 15: Trouble Shooting
Concrete Finisher Manual (Version 1) Trouble Shooting Problems Possible Causes Countermeasures a. Open fuel cap, fill fuel tank. a. No fuel. b. Switch engine on. b. Engine is switched off. c. Clean & reset plug gap. Engine stops suddenly c. Spark plug is fouled. d. -
Page 16: Technical Data
Technical Data MODEL EWT90 EWT120 76.5 x 39.1 x 44.1 80.8 x 47.2 x 44.7 DIMENSION (LxWxH) – mm (in) (1,944 x 992 x 1,120) (2,053 x 1,200 x 1,135) GUARD RING DIAMETER - in (mm) 39.1 (992) 47.2 (1,200) -
Page 17: Transportation And Storage
Concrete Finisher Manual (Version 1) Transportation and Storage Extreme care must be taken when transporting, loading or unloading this machine. CAUTION • For long-term storage, empty the fuel in the carburetor by running the engine with the fuel tap closed. •... -
Page 18: Warranty
Warranty Your new ESI concrete finisher is warranted to the original purchaser for a period of one-year (12 months) from the original date of purchase. The ESI warranty covers defects in design, materials and workmanship. The following are not covered under the ESI warranty: 1. - Page 19 Notes...
- Page 20 EQUIPMENT SYNERGY INTERNATIONAL 7422 Rock Hollow Lane (PO Box 1902) Midland Michigan 48642 (48641) 1-866-648-7101 1-336-454-2665 www.theESIchoice.com service@theESIchoice.com...