Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gigabyte GR-ES604
Summary of Contents for Gigabyte GR-ES604
- Page 1 GR-ES604 Server / Storage Server Quick Installation Guide Ver: 1.0...
- Page 2 Table of Contents SAFETY, CARE AND REGULATORY INFORMATION ..........3 CHAPTER 1 PACKING LIST ..................... 7 CHAPTER 2 SYSTEM OVERVIEW.................. 8 CHAPTER 3 SYSTEM SPECIFICATION................. 9 ..................... 9 ARDWARE SPECIFICATION CHAPTER 4 HARDWARE INSTALLATION ..............10 4.1. R & I .................
-
Page 3: Safety, Care And Regulatory Information
Safety, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. The product should be operated only from the type of power source indicated on the rating label. - Page 4 Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 5 NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the Load Numbers of all the devices does not exceed 100.
- Page 6 European Community Directive Conformance Statement This product is in conformity with the protection requirements of EC Council Low Voltage Directive (Safety) 73/23/EEC, EMC Directive 89/336/EEC on the approximation of the laws of the Member States relating to electro-magnetic compatibility. R&TTE Directive (applicable to products fitted with European modems) This modem does not require any physical and/or software additional switch settings from the User and is suitable for use only on telephone lines provided with Multi-Frequency Dialing facilities.
- Page 7 Chapter 1 Packing List Packing content list 1. GR-ES604 system * 1 2. Quick installation guide * 1 3. Mother board manual * 1 4. Mother board driver CD * 1 5. SATA cable * 2 6. SATA power Y-cable * 1 7.
-
Page 8: Chapter 2 System Overview
Chapter 2 System Overview Front view and rear view... -
Page 9: Chapter 3 System Specification
Chapter 3 System Specification Hardware specification CPU Support Intel P4 3.8GHz 800MHz Memory Type Un-Buffer DDR2 - 400 / 533 Memory ECC Support Memory Slot DIMM * 4 Memory Size Support RAID Type Firmware RAID 0, 1 Disk Type SATA Disk Number 2 / 4 (option) DVD-ROM... -
Page 10: Chapter 4 Hardware Installation
Chapter 4 Hardware Installation 4.1. Remove & Install Chassis Cover Step 1. Unlock the 3 screws from the back of the server. Step 3. Slide toward to remove the side cover. Step 3. Reverse Step 1, and 2 to replace the chassis cover. -
Page 11: I Nstall M Emory Dimm M Odule
4.2. Install Memory DIMM Module Step 1. Insert the DIMM memory module vertically into the DIMM slot. Then push it down. Step 2. Close the plastic clip at both edges of theDIMM slots to lock the DIMM module. Step 1 Step 2... -
Page 12: I Nstall Hdd And Connect Cable
4.3. Install HDD and connect cable Step 1. Inset a hard disk into hard disk blank. Step 2. Secure the hard disk wit h two screws. Step 3. Reverse the server system, lock another screw. Step 4. Connect the power cable to the hard disk. (See the arrow illustrated below) Step 5. -
Page 13: I Nstall Cpu And Heat Sink
4.4. Install CPU and heat sink Step 1. Gently lift the metal lever located on the CPU socket to the upper-right position. Step 2. Remove the plastic covering on the CPU socket. Step 3 . Align the indented corner of the CPU with the triangle and gently insert the CPU into position. - Page 14 Step 3 Step 4 Step 6 Step 5 Male Push Pin The top of Female Push Pin Female Push pin Step 7 Step 8 Step 9 Step 10...
-
Page 15: I Nstall Dvd And Connect Cable
4.5. Install DVD and connect cable Step 1. Remove the front bezel. Step 2. Push inward to remove the dummy cover. Step 3. Slide the DVD-ROM drive into the bay until it locks into place. Step 4. Secure the DVD-ROM drive with screws to the chassis. Step 5. - Page 16 Step 6 Step 7 Chapter 5...
-
Page 17: Power On Preparing
Power On Preparing Step 1 Switch the power supply input voltage to local voltage Step 2 Connect all cables. - Page 18 Chapter 6 (Storage Server Only) Recover System Step 1. Boot from DVD...
- Page 19 Step 2. Press Enter to start recovery. Step 3. Recovery completed!! Press any key to continue. Reboot your system.
- Page 20 Chapter 7 System Default Setting (Storage Server Only) Hostname : STORAGESERVER Management account : administrator Management account password : password IP address : Get from DHCP LCD module password : 9999 Chapter 8 Enter Web UI (Storage Server Only) Step 1 Open IE Step 2 Input “User name”...
- Page 21 Step 3. Reach the Web UI.
- Page 22 Appendix I More Information (Storage Server Only) Recovery DVD also contains 1. WSS 2003 Manual 2. E-office UI Manual 3. LCD module Manual 4. WSS End User License Agreement 5. i386 directory of Windows Server 2003 note: please check the DVD for the exact content...
- Page 23 Appendix II (Option) Install 4-HDD Cage Step 1. Lock the protrusion to connect the two HDD cages together. (See the arrow illustrated below) Step 2. Secure the HDD cages with screw. Step 3. Remove the front bezel and remove the screw next to the LCD panel. Step 4.
- Page 24 Step 5 Step 6 Step 7 Step 6 Step 8 Step 8...