Adjusting Bass And Treble - Oregon Scientific WRS368 User Manual

NOTE If you increase (or decrease) the volume while
the speaker is on mute, the Mute function will deactivate
and the volume will turn on again.

ADJUSTING BASS AND TREBLE

Adjusting the Wireless Remote Speaker's bass and
treble settings allows the device to playback audio with
a different range of sound and tonal effects.
To adjust the bass sound:
1. Press the button once.
2. Use the / buttons to increase or decrease the
bass. To continuously increase or decrease the bass,
press and hold the
desired bass level is reached.
3. Press the button again.
To adjust the treble sound:
1. Use the / buttons to increase or decrease the
treble. To continuously increase or decrease the
treble, press and hold the
the desired treble level is reached.
2. Press the button once to exit.
NOTE
"Auto quit" activates when idle for more than
10 seconds.
CHANGING AUDIO SOURCES
If all audio source cables are properly connected to the
Transmitter, you may change to and from any source
with a convenient press of the
backlight changes colour to indicate the change in audio
source.
AUDIO SOURCE
Source
Source
Source
1. To change the audio source, press the
The default setting is source
2. Press the button again to change the audio
source to source
change from Source
3. Press the button a third time to select the third
audio source.
4. To change the audio source at any time, repeatedly
press the button until the desired source is
shown on the LCD.
SETTING THE CLOCK
To set the time:
1. Press the button. Both hands on the clock will
begin flashing.
2. Use the / buttons to set the time: press the
button once to advance the clock by 1 minute and
press the button to turn the clock back by
1 minute. Press and hold the
to set the time faster.
3. Press the button to confirm the newly set time
and exit the clock setting mode.
WRS368 Eng R15
appears on the LCD.
/ button down until the
appears on the LCD.
/ button down until
button. The LCD
LCD COLOUR
Blue
Red
Green
button.
.
. The audio source icon will
to Source .
/ buttons down
9
The clock can only be adjusted by minute
NOTE
increments and not by hour increments.
No other buttons can be pressed while the
NOTE
setting clock function is on. "Auto quit" activates when
the function is idle for more than 30 seconds; the last
time that was set prior to idling is not saved.
NOTE Regardless of whether your Wireless Remote
Speaker is powered on or off, the clock will still show on
the LCD.
THE REMOTE LEARNING FUNCTION
NOTE Oregon Scientific does not assure the
compatibility of this product with all Audio / Video devices
existing in the market.
The Remote Learning function allows you to use a
remote control device of an audio source(s) connected
to the Transmitter to adjust the Wireless Remote
Speaker's volume and activate the mute function,
regardless of where the audio source is located.
Essentially, the remote control device of the audio
source, for example, a DVD player, becomes the
speaker's remote control device.
NOTE Make sure you are using fresh batteries in both
the audio source's remote control and in the Wireless
Remote Speaker, if used.
NOTE Incandescent or low-energy light can cause
interference with the infrared transmissions. When using
the Learning function, keep the audio source's remote
control and Wireless Remote Speaker at least
0.9 m (3 feet) away from such light sources.
NOTE "Auto quit" activates when idle for more than
60 seconds.
LEARNING TO INCREASE VOLUME USING THE
AUDIO SOURCE REMOTE CONTROL DEVICE
To teach your remote control device to increase volume:
1. Check that your desired audio source is
displayed on the LCD. You may choose from any of
the 3 sources.
2. Point the top of your audio source's remote control
device at the base of the Wireless Remote Speaker
so the infrared sensor on the remote control is in
line with the infrared sensor located at the bottom of
the speaker.
9
5/10/05, 12:53 PM