Summary of Contents for CommSky AP4600 series
-
Page 1: Quick Installation Guide
Com m Sk y WLAN AP Quick Installation Guide Indoor Wireless AP4600 Quick Installation Guide Com m Sk y Te chnologie s... - Page 2 No part of this document may be photocopied, reproduced, or translated to another language without prior written consent of the CommSky Technologies, Corp. CommSky Technologies is a trademark of CommSky Technologies, Corp., its subsidiaries, and affiliates. All other trademarks are the property of their respective owners.
- Page 3 WLAN AP Quick Installation Guide Preface This guide is aimed to assist with hardware configuration, preparation for installation, installation using several methods, and system configuration of the CommSky AP 4600 Series Indoor intelligent Access Points. The Preface includes the following contents: Applicable models: CommSky AP 4600 series of products made by CommSky Technologies, Corp.
- Page 4 Technical Support Email：support@commsky.com Phone：400-826-8847 Company Website：www.commsky.com Feedback CommSky, Corp. appreciates any feedback on problems and/or corrections with our documentation. You can contact us using the following methods: E-mail：info@commsky.com Technical support：400-826-8847 CommSky Technologies, Corp.
- Page 5 4.3 Configuration procedure ......................11 4.4 Login page ..........................13 Appendices ............................14 A1 Factory Default Settings ......................14 A2 List of Toxic and Hazardous Substances .................. 15 A3 Warranty Card ........................... 17 A4 Qualification Card ........................19 CommSky Technologies, Corp.
-
Page 6: Leds And Ports
The AP has been booted, and is in standby state. Blue Blinking A client is connected to the 5G port. Steady on The AP is booting. Alternating green and Blinking Clients are connected to both the 2.4G and 5G radio interfaces. blue CommSky Technologies, Corp. -
Page 7: Ports
The LAN 1 port can serve as an uplink interface to access the Internet LAN 1（PoE） or MAN, and as an 802.3at-compliant PoE port at the same time. LAN 2 The LAN 2 port can serve as an downlink interface CommSky Technologies, Corp. -
Page 8: Installation Preparation
Table 2 Humidity requirements Item Required Range Operating relative humidity 10% t o 9 5 % Storage relative humidity 5% t o 95% 2.3 Accessories provided with the AP The following accessories are provided with the AP: CommSky Technologies, Corp. -
Page 9: User-Supplied Installation Tools And Equipment
Power adapter, and power cable are user-supplied. 2.4 User-supplied installation tools and equipment When you install a 4600 access point, you may need the following tools: Phillips screwdriver Rubber hammer Level Percussion drill with Marker Ladder matching drills CommSky Technologies, Corp. -
Page 10: Ap Installation
For more information about AP LEDs, see Section 1, LEDs and ports. Ensure all necessary cabling have been installed. AP4600 supports 802.at-compliant PoE. For best performance, Commsky recommends to only use GE connection to supply power to the device. - Page 11 Step 2 Locate the AP so that the wall screws go into the mounting holes, then push down a few mm to secure the AP into place. Figure 2 Mounting AP on screws 1：Screws 2：AP wall-hanging holes CommSky Technologies, Corp.
- Page 12 Insert two wall anchors and knock them down into the holes. Figure 3 Drill holes locations Step 2 Affix ceiling mount to ceiling using two screws. Figure 4 Affix ceiling mount 1：Mounting holes on the circular support 2：Expansion screws CommSky Technologies, Corp.
- Page 13 2：Circular support mounting holes 3：Pan head screws Step 4 At a slight counter-clockwise angle, match the housing bracket and the ceiling mount, then rotate the AP clockwise to secure in place. Figure 6 Secure AP to ceiling CommSky Technologies, Corp.
-
Page 14: Connecting The Power Supply
Prior to powering up, please ensure that there is a stable supply of power delivered to the equipment. Regardless of using public utilities, UPS, or private generators, CommSky recommends to centralize power supplied to the equipment. Such a power network is simple to use, safe to operate, flexibly configured, and easy to maintain. - Page 15 Figure 9 PoE connection 3.5.5 Post power-up checklist Once AP is powered up, please make sure AP’s LEDs are operating properly. For the list of AP LEDs and their purpose, please consult to Section 1: LEDs and Ports. CommSky Technologies, Corp.
-
Page 16: Configuration Guide
An Ethernet cable; A PoE module or PoE switch. Note Due to lack of compatibility among different browsers, CommSky recommends using the Google Chrome browser, v20 or later, for best user experience. 4.2 Device default configuration When factory default HTTP service is enabled on the AP, users can log in to the AP’s web service interface using default login credential. - Page 17 Com m Sk y WLAN AP Quick Installation Guide Figure 5-1 Ethernet Interface Double click on 【Internet（TCP/IPv4）】to configure static IP address and corresponding network mask, as show below: Figure 5-2 Internet Protocol (TCP/IPv4） CommSky Technologies, Corp.
-
Page 18: Login
Figure 5-3 Login Web Page After entering username and password, click <Log On> button or <Enter> key to perform logon. Once successfully logged on, user is ready to perform AP configuration. Figure 5-4 Configuration Page CommSky Technologies, Corp. -
Page 19: Appendices
A1 Factory Default Settings Parameter Default Value LAN IP Address 192.168.0.50 LAN Network Mask 255.255.255.0 Login Web page username admin Login Web page password admin SSID (2.4GHz/5GHz) CommSky_2.4G/CommSky_5G WPA Pass Phrase 12345678 Telnet Service Enabled HTTP Service Enabled CommSky Technologies, Corp. -
Page 20: A2 List Of Toxic And Hazardous Substances
○ Power adapter 3 × ○ ○ ○ ○ ○ Internal power 1 × ○ ○ ○ ○ ○ Internal power 2 × ○ ○ ○ ○ ○ Internal power 3 × ○ ○ ○ ○ ○ CommSky Technologies, Corp. - Page 21 ×: At least one source materials used for this part contains toxic or hazardous substances whose level is above the SJ / T11363-2006 prescribed limits. Note: Environmental aging effect is determined in accordance with the referenced product under normal operating conditions (such as temperature and humidity). CommSky Technologies, Corp.
-
Page 22: A3 Warranty Card
15 days after the date of product manufacture. 4. All CommSky exchanged / repaired products are entitled to 180 days of warranty service, counting from the day of exchange / repair, or continue with existing warranty service, whichever is longer. - Page 23 6. Contact CommSky technical support at +86-400-826-8847 or website www.commsky.com obtain warranty service. Warranty Service Locations： Through your purchasing product agent / distributor, or contact CommSky service personnel. ※ CommSky Technologies Corporation reserves the final right to interpret and modify contents of this warranty card. Warning This device complies with part 15 of the FCC Rules.
- Page 24 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. CommSky Technologies, Corp.
- Page 25 Com m Sk y Te chnologie s U.S．California Hang Zhou．China CommSky Technologies(Hang Zhou)Co.,Ltd Com m Sky Technologies，Corp. Jiang Nan Xing Zuo,Unit B2,F6 Chun Xiao Road 529# 4677 Old I ronsides Drive, # 400 Hang Zhou, China Sant a Clara, California 95054...