Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NAVI R330g
Summary of Contents for NAVI R330g
- Page 1 Router R330g Quick Setup Guide V1.0 Quick Setup Guide V1.0...
-
Page 2: Table Of Contents
End users must follow the specific operating instructions for satisfying RF exposure compliance. Table of Contents TABLE OF CONTENTS ............錯誤! 尚未定義書籤。 CHAPTER 1 NAVI R330G’S QUICK SETUP ............3 ’ ..........3 OUTER UICK... -
Page 3: Chapter 1 Navi R330G's Quick Setup
Chapter 1 Navi R330g’s Quick Setup Router Mode’s Quick Setup Instruction Please open a Microsoft Internet Explorer, and enter http://192.168.100.1 (Default Gateway) into browser’s blank, then you will see the configuration page below: Please input in the blanks, the factory default values for User Name and Password are “admin”... - Page 4 Please select the “Router”, and then click on “Apply Change”, so you will go to the page of “System Rebooting”. Quick Setup Guide V1.0...
- Page 5 After 60 seconds, you will go back to the main page of “Operation Mode”, and see the “Router Home” appearing on the left sub-menu, then please click on “Quick Setup”, and you will see the main page of “Router Quick Setup” shown below, which means you have already enabled the operation mode of “Router Quick Setup”.
-
Page 6: The Introduction Of Router Mode's Quick Setup
The Introduction of Router mode’s Quick Setup After you go to the main page of “Router Quick Setup”, please click on “Next” right side below, and go to the next page to do each setting step by step: Quick Setup Guide V1.0... -
Page 7: Time Zone Setting
1.2.1 Time Zone Setting The section provides to change the Time. However, change the router’s date and time does not affect the date and time on your PCs. Please select your time Zone Please click on “Next” button to connect to next step. Quick Setup Guide V1.0... -
Page 8: Lan Interface Setup
LAN Interface Setup If you are using the Mini Router with multiple PCs on your LAN, please set up this function for multiple users to connect it. The default LAN IP for R330g is 192.168.100.1. Please click on “Next” button to connect to next step. -
Page 9: Wan Interface Setup
1.2.3 WAN Interface Setup R330g supports 4 connection types to WAN, select one of the WAN connection modes required by your ISP in below “WAN Access Type” page, the WAN setting pages will differ depending on what kind of WAN Type you select. -
Page 10: Wan Interface Setup-Static Ip
Choose Static IP Address if all WAN IP information is provided to you by your ISP. R330g will not accept the IP address if it is not in this format, and the blanks of “IP Address”, “Subnet Mask” and “Default Gateway” must be input. -
Page 11: Wan Interface Setup- Dhcp Client
1.2.3.2 WAN Interface Setup– DHCP Client Choose DHCP Client to obtain IP address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. Please click on “Next” button to connect to next step. Quick Setup Guide V1.0... -
Page 12: Wan Interface Setup- Pppoe
1.2.3.3 WAN Interface Setup– PPPoE If your ISP uses PPPoE connection, your ISP will provide you with a username and password. Input it by your ISP provided. Input it by your ISP provided. Please click on “Next” button to connect to next step. Quick Setup Guide V1.0... -
Page 13: Wan Interface Setup- Pptp
1.2.3.4 WAN Interface Setup– PPTP Some DSL service providers supply a special DSL modem in Europe or Big Pond Cable in Australia. This kind of modem only supports the PPTP tunnel to access the Internet; Please enter the account’s information of Account and Password which provided by your ISP. -
Page 14: Wireless Basic Settings
1.2.4 Wireless Basic Settings The first step of setting up the “Wireless Basic Settings” is to give a name for SSID, herewith the default name of SSID is Navi_R330g, it’s suggested to use. Select the suitable item for you to use. It’s suggested to use. -
Page 15: Wireless Security Setup
1.2.5 Wireless Security Setup The “Encryption” item of “Wireless Security Setup” is optional; which means you can choose it under your demand, herewith it’s divided into two categories of “WEP” and “WPA”, if you want to protect your transmitting data; you can select it depended on the level of your request. - Page 16 It has low level (64-bit) and high level (128-bit). It has “10 characters” and “26 characters”; it will be listed under your selection is low level (64-bit) or high level (128-bit). No matter if you selection is either 10 or 26 hexadecimal digits (0~9, a~f, and A~F) in the pull-down menu bar of “Key Format”;...
- Page 17 Please select it under your demand Select it by your request Please input it as necessary After setting up, please click on Finished” button to connect to next step. Quick Setup Guide V1.0...
-
Page 18: Quick Setup Finish
1.2.6 Quick Setup Finish The Quick Setup has been completed successfully when you see this screen. The system will be rebooting automatically and goes to the Product’s Diagram Homepage after 60 seconds. Quick Setup Guide V1.0...