Poulan Pro 96192001600 Owner's Manual
  1. Manuals
  2. Brands
  3. Poulan Pro Manuals
  4. Snow Blower
  5. 96192001600
  6. Owner's manual
Poulan Pro 96192001600 Owner's Manual

Poulan Pro 96192001600 Owner's Manual

Poulan pro snow thrower owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

IMPORTANT MANUAL
OWNER'S MANUAL
MODEL NUMBER:
PR5524ES
SNOW THROWER
Always Wear Eye Protection During Operation
Do Not Throw Away
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
In struc tions. Fail ure to do so
can result in serious injury.
414643 Rev 3 12.07.07 TH
Printed in the U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Poulan Pro 96192001600

Summary of Contents for Poulan Pro 96192001600

  • Page 1 IMPORTANT MANUAL OWNER'S MANUAL MODEL NUMBER: PR5524ES SNOW THROWER Always Wear Eye Protection During Operation Do Not Throw Away WARNING: Read the Owner's Manual and fol low all Warnings and Safety In struc tions. Fail ure to do so can result in serious injury. 414643 Rev 3 12.07.07 TH Printed in the U.S.A.

  • Page 2: Safety Rules

    Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. Look for this symbol to point out im- por tant safety precautions.

  • Page 3: Table Of Contents

    6. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

  • Page 4: Assembly / Pre-Operation

    PARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.
  • Page 5 ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely.
  • Page 6 ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

  • Page 7: Operation

    OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product.
  • Page 8 SPARK PLUG SAFETY IGNITION CHOKE CON- TROL THROTTLE / ENGINE CONTROL RECOIL POWER (AUXILIARY) CORD STARTER PLUG ELECTRIC HANDLE START BUTTON PRIM ER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.
  • Page 9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - 00155 ments or repairs.

  • Page 10: To Move Forward And Backward

    CHUTE DEFLECTOR LOW POSITION FIG. 13 TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. •...

  • Page 11: Before Starting The Engine

    TO ADJUST SKID PLATES (See Fig. 17) TO ADJUST SKID PLATES (See Fig. 17) NOTE: The wrench provided in your parts bag may be NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. used to adjust the skid plates.
  • Page 12 COLD START - ELECTRIC STARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place. 2. Place throttle control in FAST position. 3.

  • Page 13: Maintenance

    GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made periodically to properly maintain your snow thrower.

  • Page 14: To Change Engine Oil

    AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease.

  • Page 15: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: To avoid serious injury, before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4.

  • Page 16: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating po si tion and hold the snow thrower han dles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt chang ing process.

  • Page 17: Storage

    SERVICE AND ADJUSTMENTS NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and cor ro sion. ENGINE See engine manual. CARBURETOR Your carburetor is not adjustable.

  • Page 18: Troubleshooting

    TROUBLESHOOTING See appropriate section in manual unless directed to a qualified service centre. PROBLEM CAUSE Does not start 1. Fuel shut-off valve (if so equipped) in OFF position. 2. Safety ignition key is not inserted. 3. Out of fuel. 4. Throttle in STOP position. 5.
  • Page 19 SERVICE NOTES...

  • Page 20: Repair Parts

    SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY 07 AIG plug_r1...
  • Page 21 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY KEY PART 191079 188909 155377 180355 72270505 163183 404928X428 404931X479 178675X008 175322 10040500 19111507 74940516 405637 179582 73800400 155377 178777X479 72270506 174658 174697 198636 174762X479...
  • Page 22 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE 07_Chute-knob_2...
  • Page 23 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
  • Page 24 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS HANDLES...
  • Page 25 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS HANDLES KEY PART NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
  • Page 26 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS DRIVE...
  • Page 27 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS DRIVE NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
  • Page 28 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS CHASSIS / ENGINE / PULLEYS 07Chassis-chain-cord-Tec_3 10 21...
  • Page 29 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS CHASSIS / ENGINE / PULLEYS KEY PART DESCRIPTION 414557 Spring, Traction Idler 180522 Pulley, Idler (2-1/4) - - - Engine, Tecumseh, Model Number LH195SP-67510D (For engine service and replacement parts, call Tecumseh...
  • Page 30 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS WHEELS / DECALS...
  • Page 31 SNOW THROWER - - MODEL NO. PR5524ES (96192001600) REPAIR PARTS WHEELS / DECALS NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

  • Page 32: Warranty

    This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975. LIMITED WARRANTY In Canada contact: Poulan Pro, Customer Service Department 5855 Terry Fox Way Mississauga, Ontario L5V 3E4...

This manual is also suitable for:

Pr5524es

Table of Contents