Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Swann SW2020R
Summary of Contents for Swann SW2020R
- Page 1 6KG WASHING MACHINE SW2020R User Instructions Swan Helpline No. 0845 610 4118...
-
Page 2: Table Of Contents
THE CONTENTS SECTION 1: BEFORE USING Safety warnings Recommendations SECTION 2: INSTALLATION Removal of transportation screws Ensure the washing machine is level Electrical safety Water supply connection Water drain connection SECTION 3: TECHNICAL SPECIFICATIONS SECTION 4: CONTROL PANEL Start/Pause button Function indicator lights Function buttons Program knob... -
Page 3: Section 1: Before Using
SECTION 1: BEFORE USING KEEP THIS MANUAL IN A CONVENIENT PLACE SO YOU CAN REFER TO IT FOR THE SAFE AND PROPER USE OF THE APPLIANCE SAFETY WARNINGS Do not use a multiple socket or extension cord. Do not insert a plug with damaged or broken cord into the socket. If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. -
Page 4: Section 2: Installation
If you do not use your machine for a long time, unplug, turn off the water supply and leave the door open in order to prevent the formation of unpleasant odours. As a result of the quality control procedures, a certain amount of water may remain in your machine. -
Page 5: Electrical Safety
There are adjustable feet under the bottom of the washing machine. Before use, they should be adjusted so that the washing machine is level. This will minimize vibrations and thus noise during. First, loosen the plastic adjustment nut. Adjust by rotating the feet upwards or downwards. We recommend using a spirit level to check the item is level. -
Page 6: Water Supply Connection
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows (refer to the plug wiring diagram). The wire which is colored BLUE must be connected to the terminal which is marked with the letter N or colored Black. -
Page 7: Water Drain Connection
2) Connect the curved end of the hose to the water inlet valve located at the rear right hand top corner of the unit. Ensure the connection is tightened adequately so that it will not leak. 3) Make sure there a no kinks or bends in the hose. 4) Turn on the tap and check that there are no leeks from either connection. -
Page 8: Section 3: Technical Specifications
SECTION 3: TECHNICAL SPECIFICATIONS 47 LT Maximum dry laundry capacity (kg) Recommended loading (kg) Height (cm) Width (cm) 59,6 Depth (cm) Swan Helpline No. 0845 610 4118... -
Page 9: Section 4: Control Panel
SECTION 4: CONTROL PANEL 1-Detergent drawer 5-Program knob 2-Start/pause light 6-Start/pause button 3-Function indicator lights 7-Function buttons 4-Program ready light 8-Program end light START/PAUSE BUTTON Used to start a selected program or pause during running. WARNING! It is required for the program knob to be brought to O(off) position before selecting the program or changing a continuing program. - Page 10 If you do not want your sensitive clothes to be spinned or you want them to be spinned sensitively, turn the program knob to I (off) position. Bring the program knob on one of the draining or spinning programs you desire and press the start/pause button.
-
Page 11: Program Knob
PROGRAM KNOB The program knob also acts as the on/off switch. Position the indicator on the knob pointing towards I to turn the machine off. The program knob is also used to select the required program. This is done by rotating the knob in a clockwise or anti-clockwise direction. 13 SPORT CLOTHES PROGRAM... - Page 12 SECTION 5: OPERATING THE WASHING MACHINE ! Ensure the washing machine is plugged in and the water tap is on. ! There may be some residual water in the machine, when first opening the drum door. This is normal and is the result of factory testing. ! It is recommended that the washing machine is run without laundry in for the first time of use.
- Page 13 Selecting detergent The washing efficiency and the performance is determined by the quality of detergent used. Special non-foaming detergent produces good washing results. Use specific detergents for synthetic and woollen goods. Do not use dry cleaning agents such as trichloroethylene and similar products.
- Page 14 Starting a washing cycle 1. Select the program and additional functions appropriate the laundry load from Table-1. 2. Rotate the program knob, so that the indicator on the knob is pointing towards the required program mode (You should feel a slight click which will indicate when a program has been selected).
- Page 15 At the end of the wash cycle 1. Your machine will automatically stop when the program you have selected ends. 2. The program end light will be on. 3. Rotate the program knob to I (This will turn the unit off).
- Page 16 MAX DRY WASHING WATER ENERGY DETERGENT TEMP LOAD PROGRAM TIME CONS. CONS. TYPE OF LAUNDRY EXPLANATIONS COMPART. (°C) CAPACITY (MIN.) ** (lt) ** (kWH) ** (kg) Dirty, boil, cotton and 1 COTTON 90 2.06 linen textile 2 COTTON 60 Very dirty, cotton, 1.41 (PREWASH) coloured and linen textile...
- Page 17 MAX DRY WASHING WATER ENERGY DETERGENT TEMP LOAD PROGRAM TIME CONS. CONS. TYPE OF LAUNDRY EXPLANATIONS COMPART. (°C) CAPACITY (MIN.) ** (lt) ** (kWH) ** (kg) 13 SPORT All sport clothes 0.47 Sport clothes and jeans CLOTHES Slightly dirty, synthetic or 14 SYNTHETIC synthetic mixture sensitive Nylon socks,...
-
Page 18: Section 6: International Washing Signs
SECTION 6: INTERNATIONAL WASHING SIGNS Washing Do not wash Lukewarm iron. Medium hot iron. temparature. (hand wash) Do not tumble Hot iron. Do not iron. Hang to dry. dry. Drip dry. Dry flat. Do not bleach. Handy to bleach. All of these are dry cleaning symbols. The letters are to instruct the cleaner what type of solvent to be used. -
Page 19: Section 7: Maintenance And Cleaning
SECTION 7: MAINTENANCE AND CLEANING Unplug your machine. Close the water tap. WATER INLET FILTERS On the tap part of your machine’s water inlet hose and at the ends of water inlet valves, there are filters to prevent entrance of the dirt and foreign materials in the water to the machine. -
Page 20: Pump Filter
PUMP FILTER ! WARNING - The water inside the pump maybe hot, wait for it to cool before performing this task. The filter system prevents lint from entering pump this will increase the pumps lifespan. It is recommended that the filter is checked and cleaned every month. -
Page 21: Detergent Drawer
DETERGENT DRAWER Detergents may form a sediment in your detergent drawer or in housing of the detergent drawer over time. To clean the detergent drawer. Pull the detergent drawer to the end. (DIAGRAM-1) Lift the front of the drawer, press down the blue tab and continue to pull until the drawer is out. -
Page 22: The Drum
5. The program ready light will be on. 6. Run the program by pressing the start/pause button. 7. Unplug your machine when the program is over (program end light is on). The remaining water inside the machine will be drained and thus formation of ice in the machine will be prevented. -
Page 23: Section 8: Trouble Shooting
SECTION 8: TROUBLE SHOOTING FAILURE PROBABLE CAUSE SOLUTION Insert the plug into the It is unplugged. socket. Your fuse is defective. Change your fuse. Check the power in The power is off. household. Start/pause button has Press the start/pause Your machine does not not been pressed. - Page 24 FAILURE PROBABLE CAUSE SOLUTION There is a small It does not prevent amount of clothes in operation of the the device. machine. Do not exceed the Excessive amount of recommended quantity clothes are filled in the Your machine is of clothes and spread machine or the clothes vibrating.
- Page 25 FAILURE PROBABLE CAUSE SOLUTION Clothes exceeding the Reduce the amount of maximum capacity laundry placed in the has been filled in your drum. machine. Use the amount of The washing result is Your water may be detergent according to not good. hard.
-
Page 26: Section 9: Automatic Failure Detection System
SECTION 9: AUTOMATIC FAILURE DETECTION SYSTEM Your machine is equipped with systems which will both take the necessary precautions and warn you in case of any failure by controlling it self constantly during the washing processes. FAILURE FAILURE PROBABLE THE PROCESS CODE INDICATOR FAILURE... -
Page 27: Swan Helpline No. 0845 610 4118
FAILURE FAILURE PROBABLE THE PROCESS CODE INDICATOR FAILURE TO BE DONE Ensure the water tap is fully open and their is a constant flow of water.If the problem is still There is no continuing,your The program supply of water machine will Err 02 ready light or the water... - Page 28 FAILURE FAILURE PROBABLE THE PROCESS CODE INDICATOR FAILURE TO BE DONE Shut down your machine and The heater of your The start/pause unplug. Turn off machine or the Err 05 light and program your tap and heat sensor has end light blink. contact a service failed.
- Page 29 Still not solved the problem? If a visit is required and the conditions of the Guarantee are fully satisfied a repair may be offered without charge. If a replacement appliance is required a charge may be made which reflects the wear and tear on the original appliance. If no fault is found with the appliance a ‘Call out Charge’...
- Page 30 WASTE ELECTRICAL RECYCLING This symbol indicates that this product is classed as Electrical or Electronic Equipment and should not be disposed of with other household waste. The Waste Electrical and Electronic Equipment (WEEE) Directive has been introduced across the European Union: to recycle waste electrical products using the best available recovery and recycling techniques in order to minimize the impact on the environment...