Using The Wake Up Timer; Using The Sleep Timer - Sanyo DC D30 Instruction Manual

To set the timer again using the same settings
1. Press the TIMER switch. The timer ON time is displayed.
2. Press the SET/CLEAR switch within 5 seconds.
Every time steps 1 and 2 are repeated, the mode alternates
between timer standby and timer off modes.
3. Press the POWER switch to switch off the power.
Note:
If the SEVCLEAR switch is pressed while the timer is being set, the
original display returns.
The timer mode is released if a power failure occurs during timer
controlled operation.
The timer will not operate if a power failure lasts for more than 30
seconds durina standbv mode.
USiNG THE WAKE UP TiMER
Setthewake-uptime, source to be heard and volume level. Atthe set time,
the set source will be heard. The sound will be gradually increased from
a no-sound level to the volume setting (fade-in). The power will turn off
after 60 minutes. The WAKE UP timer will function every day unless it is
released.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Press the WAKE UP switch.
I I
I
WAKE UP
5:30
AM
I
The previous wake-up time setting appears.
Press the MEMORY switch within 5 seconds.
W)+(UP
Setthewake-uptime by pressing the V or A TUNING switch, then
mess the MEMORY switch.
I I
I
\l/
w9KffP
I I
t#
1/
\l/
Vwv
I
The previous source setting blinks.
Select the source using the V or A TUNING switch.
rCd_TA_TU~
For waking up to radio sound
Perform step 4 above until "TU" blinks on the display. Then follow the
steps "b" and "c" of "For radio reception" under "USING THE ON/
OFF TIMER".
Press the MEMORY switch.
I
The previous volume level setting blinks.
Select the volume level using the V or A TUNING switch.
0eje2m3w4w~6w7
To check the actual sound level, it is recommended that the timer
beset once and the level heard. This can be checked by setting the
timer 2 minutes later than the present time.
The sound will not be faded in at the "O" level. In this case, the
sound will be heard at the previous VOLUME control setting.
Except setting the "0" level, the audio muting function will not
operate at the set time even if it is on ("MUTE" is blinked).
Press the MEMORY switch.
The original display returns, then the wake-up standby mode is
activated. "WAKE UP" remains lit.
Prepare the sources to be used.
Press the POWER switch to switch off the power.
Press the POWER switch to switch off the power after the power is
turned on at the wake-up time.
Even after the WAKE UP timer operation has completed, "WAKE UP"
remains lit and the standby mode continues.
To check the timer settings
Press the WAKE UP switch repeatedly. The timer settings are displayed
in the following order:
- Wake-up time
Source (If the tuner is being used as the source, the band, preset
number and frequency are displayed.)
- Volume level
- Original disday returns.
To chang~the sett~ng~, press the WAKE UP switch to select the setting to
be changed, then press the MEMORY switch so that the display blinks.
Change the setting as explained above.
To release the WAKE UP timer
Press the WAKE UP switch, then press the S=/CLEAR switch. "WAKE
UP" disappears.
USiNG THE SLEEP TiMER
This timer automatically switches off the power after a preset time has
elapsed. The volume will gradually be reduced (fade-out) during the 1-
minute period before the unit turns off. There are 7 time periods available:
90, 60, 50, 40, 30, 20 and 10 minutes.
1.
2.
3.
Press the SLEEP switch.
I
I
J
The previous sleep time setting blinks.
Press the SLEEP switch within 5 seconds to select the desired sleep
time.
P90 -D60 ~50~40-30-20 -10- (released) 1
If the SET/CLEAR switch is pressed, the original display returns
and the SLEEP timer setting mode is released.
Allow 5 seconds to elapse or press the MEMORY switch.
The original display returns and the SLEEP timer starts. "SLEEP"
remains lit.
To check the remaining sieep time
Press the SLEEP switch. The remaining time is displayed. After several
seconds, the original display returns.
To reiease the SLEEP timer whiie in operation
Press the SLEEP switch, then press S~/CLEAR. The timer is also
released if the power is switched off.
Timer priorities
The ON/OFF timer settings are released if the actual time reaches the
ON time setting during WAKE UP timer operation.
During ON/OFF timer operation, the WAKE UP timer will not operate
but the WAKE UP timer setting is retained.
The SLEEP timer has priority over the ON/OFF and WAKE UP timers.
The power is switched off by the SLEEP timer. The ON/OFF timer
setting is released, but the WAKE UP timer setting is retained.
-15-