ND IP 39-60 ePCR Quick Installation Manual

Door access control with the voip interface

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Door Access Control with the VoIP interface

IP 39-60 ePCR

Release 1.02

Table of Contents

Summary of Contents for ND IP 39-60 ePCR

Page 3 NISTA DEVICES GmbH 2013 © All Rights Reserved NOTICE This document refers to the Nista Devices GmbH Door Access Control devices with VoIP protocol capabilities. Additional copies of this manual may be obtained from Nista Devices GmbH. Reproduction of this manual or parts thereof without written permission from Nista Devices GmbH is strictly prohibited.
Page 4: Table Of Contents
NISTA DEVICES GmbH 2013 © All Rights Reserved Table of Contents Introduction ................................5 List of Available Models ............................ 5 Product Overview ............................... 5 IP Door Phone package content ..........................6 IP 39-60ePCR Front Panel ............................7 IP Door Phone main functionality..........................8 Installation ..................................
Page 5: Introduction
NISTA DEVICES GmbH 2013 © All Rights Reserved 1 Introduction The Nista Device's IP Door Phones are standalone SIP phones, which maximize functionality of the VoIP network. Integrated into SIP Proxy as extension IP Door Phone allows voice and video communication and doors control within an enterprise multiple branches, which is operated under single IP network.
Page 6: Ip Door Phone Package Content
NISTA DEVICES GmbH 2013 © All Rights Reserved 3 IP Door Phone package content • IP Door phone unit • Wall Installation kit • Set of connectors • Hex key wrench for security screw 1. In case if POE powering is not available it is possible to use the External Power Adapter (not supplied). External Power Adapter shall correspond to following technical parameters: •...
Page 7: Ip 39-60Epcr Front Panel
NISTA DEVICES GmbH 2013 © All Rights Reserved 4 IP 39-60ePCR Front Panel Figure 4-1 The IP Door Phone Unit Front Panel • ▲▼ – scroll a speed dial directory. • C – enter the programing mode or use as a “Backspace” button •...
Page 8: Ip Door Phone Main Functionality
NISTA DEVICES GmbH 2013 © All Rights Reserved 5 IP Door Phone main functionality. • The IP Door Phone unit can be integrated with IP PBX (Server / SIP-Proxy) as a SIP extension. IP Door Phone can be connected to IP PBX directly or via IP router, HUB or Switch. •...
Page 9: Installation
NISTA DEVICES GmbH 2013 © All Rights Reserved 6 Installation 6.1 Mounting The Door phone shall be mounted on the wall or into the wall using the rear metal installation rack provided with the unit. 1. Unscrew the secret Torx t-6 screws on the bottom part of the unit.
Page 14: Ip 39-60 Connections
NISTA DEVICES GmbH 2013 © All Rights Reserved 6.2 IP 39-60 Connections The IP Door Phone can be installed as standalone access control device. Figure 6-1 shows the terminal locations on the wire connectors provided with the unit. This connector is then inserted into the mating connector located at the base of the internal PCB.
Page 15 NISTA DEVICES GmbH 2013 © All Rights Reserved Figure 6-1The IP Door Phone PCB Module 1. Remove the front panel cover from the Door Phone unit and find the wiring connector on the PCB module. ( See Figure 6-1 ) 2.
Page 16 NISTA DEVICES GmbH 2013 © All Rights Reserved Note: 1. Draw attention on NO/NC jumper position. The closed ‘Center’ Pin +’NO’ pin means the ‘Normally open’ relays status in powered mode. The closed ‘Center’ Pin +’NC’ pin means the ‘Normally Close’ relays status in powered mode Important: To set device in operational mode, switch 1 on PCB shall be switched to...
Page 17 NISTA DEVICES GmbH 2013 © All Rights Reserved Connector’s PINs Description Speaker Connector POE/LAN connection 6- Ethernet External power supply 5VDC 2A input (if no POE applied). 5VD (5V DC) Draw attention on connection polarity: +5V and GND marked on PCB (Figure 6-1) The External Power Supply does not included in standard IP39-60 package Door status detector.
Page 18: Access To Web Programming
NISTA DEVICES GmbH 2013 © All Rights Reserved 7 Access to WEB Programming 10. The unit comes configured with the default IP address: 10.10.10.6 . To access to the unit’s WEB programming if your LAN configured with different subnet please make following: 11.
Page 19 NISTA DEVICES GmbH 2013 © All Rights Reserved • In LAN properties window select ‘Internet Protocol Version 4 (TCP/IPv4) option and click on ‘Properties’ button • Select 'Use the following IP address:' and insert IP Address and Subnet mask as shown on the picture below...
Page 20 NISTA DEVICES GmbH 2013 © All Rights Reserved • Press ‘OK’ to accept settings Launch Internet browser and type 10.10.10.6 in address bar. 13. Log in to the Nista web GUI using the appropriate user’s credentials IP 39-60 provides different management levels for WEB-Management: Administrator and User •...
Page 21 NISTA DEVICES GmbH 2013 © All Rights Reserved Note: 14. The default IP Door Phone IP address is 10.10.10.6 and it is configured as ‘Static’ IP Address. 15. The default web-programming Administrator credentials are: • User name: ‘admin’ – For Administrator management level and ‘user’ – for User management level •...
Page 23: Reset Device To Factory Default Configuration
NISTA DEVICES GmbH 2013 © All Rights Reserved 8 Reset device to Factory Default Configuration IP Door phone can be reset to its Factory default configuration by using following actions: 1. Via WEB-Management interface ( See Chapter 7.8 in User Manual document) 2.