Getting To Know Your Cleaner; Using Your Cleaner; Cleaner Maintenance - Hoover DIVA User Manual

GETTING TO KNOW YOUR CLEANER

A. Main Handle
B. Permanent Exhaust Filter
C. Floor type selector*
D. Carpet and Floor nozzle (GP)**
D1. Carpet Nozzle (CA)**
D2. Hard Floor Nozzle (Hf)**
D3. Hard Floor Nozzle (HF)**
E. Bin Door Release Button
F. Bin Door
G. Power Control Knob*
H. Cord Grip
I. Carry Handle
J. Rotating Upper Cord Hook
K. Lower Cord Hook
L. Bin Top Cover
M. Filter mesh
N. Pre-motor Filter
O. Dust Bin
P. Parquet Nozzle*
PREPARING YOUR CLEANER
1. Remove the accessories from the main packaging. You will find the following:
• Cleaner body
• Cleaner handle
• Parquet nozzle*
• Carpet and Floor nozzle (GP)**
• Hard Floor Nozzle (HF)**
• Carpet Nozzle (CA)**
2. Assemble the cleaner handle and fix in position with the supplied screw. [1a,1b]
3. secure the nozzle to the product [1c].
For models equipped with Carpet & Floor nozzle*:
Secure the nozzle to the product. Press the floor type selector pedal on the nozzle [1d]
to select the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
For models equipped with Parquet nozzle*:
Secure the nozzle to the product in the same way as the main nozzle. For parquet floors
and other delicate floors.
*Certain Models Only ** Certain models only, nozzles may vary according to model
For models equipped with Carpet Nozzle*:
secure the nozzle to the product in the same way as the main nozzle. Use the Carpet
nozzle for deep cleaning on carpets.
Cord storage:
To store the cord after cleaning wrap the cord around the two cord hooks. [2]
NOTE: During cleaning, the cord can be clipped in the cord grip on the rear of the handle
to avoid any interference while cleaning.

USING YOUR CLEANER

Power switch:
1. To switch the cleaner on, rotate the power control knob. [3]
2. To switch off the product, rotate the same knob.

CLEANER MAINTENANCE

EMPTYING THE DUST BIN ASSEMBLY *
a) Lay the cleaner on a flat surface, pull back the door release button and remove the
transparent door. [4]
b) Remove the bin assembly. [5]
c) Remove the bin top cover assembly from the container, by rotating the container and
bin top cover in opposite directions. [6]
d) Empty the debris from the container into a bin.[8] Check if it is necessary to clean the
relative filters, as described in the "Maintaining the filters" section.
e) Refit bin top cover to container assemble the dust container and filter assembly to the
product ensuring you keep the container ribs aligned with the cleaner body as shown
[9b], once aligned push dust bin assembly fully into position.
NOTE: Hoover recommends to inspect and wash if necessary, the mesh and the filters
after each full container, see maintaining filters section.
MAINTAINING THE FILTERS *
a) To access the washable HEPA filter, rotate the mesh filter assembly in the opposite
direction from the bin top cover. [7]
b) Remove the mesh and remove all dust and debris, wash mesh if required but ensure
it is dry before refitting. [8a]
c) Gently tap the filter to remove any excess dust and if required wash the HEPA filter
thoroughly under hand warm water until water runs clear. [8b]
d) Remove excess water by shaking and leave to dry for 24 hours. [8c] Refit filters to the
cleaner only when completely dry.
e) When refitting the filter ensure mesh is assembled correctly as per [8d] then reassemble
filter to bin top cover [8e] and finally fit to container ensuring correct alignment. [9a]
2
GB