Table of Contents
Advertisement
™
ProSeries Blocker
™
AUTOMATICALLY BLOCKS AND ROUTES
SCREENED CALLS WITH CALLER ID
With Back Lighted Display
1,000 Blocked Memory Slots
Virtual Memory Management
Patent Pending
Operations Manual
Color version of manual available
at http://www.digitone.com/
OS Version Digitone ProSeries Blocker
Copyright MCMXC-MMXVI. All Rights Reserved. Digitone ProSeries Blocker and
Personal Communicator are trademarks of Digitone Communications.
Advertisement
Table of Contents
Summary of Contents for Digitone proseries blocker
- Page 1 With Back Lighted Display 1,000 Blocked Memory Slots Virtual Memory Management Patent Pending Operations Manual Color version of manual available at http://www.digitone.com/ OS Version Digitone ProSeries Blocker Copyright MCMXC-MMXVI. All Rights Reserved. Digitone ProSeries Blocker and Personal Communicator are trademarks of Digitone Communications.
- Page 2 Just connect your telephone and you’re ready to go. You don’t need to set any codes as Digitone’s DPB can operate right out of the box. No Battery Backup is Needed - If there is a power outage, all of the program settings remain intact.
- Page 3 Each new call received thereafter will replace old calls from the Top of the list (FIFO). Only one Digitone DPB is needed for any single telephone line you want to monitor. It can be connected to any analog telephone service; cable modem, gateway, VoIP adapter, wall plate or phone jack in your home or office.
- Page 4 ™ Automatic Caller ID Call Routing Caller ID service from your phone company is required for Digitone’s DPB to work. The first call to your DPB unit will initialize the Clock and Date to the current date and time. Automatic call routing will begin to work right after the first call when Caller ID information is displayed.
- Page 5 Block Button – Blocking Names This feature only works with the Block button on Call History entries and not in Programming. Block up to twenty individual names with or without numbers that use the same name with different numbers. Using the Call History Up or Down view buttons, press the Block button Once quickly on the front panel on the selected Name you want to block.
- Page 6 Service” until line service is connected to the LINE port. Power must be connected to the DPB with the Digitone supplied 24VDC power adapter. You will not be able to program the DPB unless the above conditions are met. Leave all other phone devices you have connected to their own power supplies.
- Page 7 from ringing and receiving Caller ID. If the caller is an Invited caller then the Caller ID information will display on the next ring to the phones connected to the TEL phone port thereafter. This stops unwanted Caller ID information from being received by the phones connected to the DPB TEL phone port. If you want to hear the first ring, enter programming: press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code”...
- Page 8 Deleting Code 40 Blocked Numbers “Can Not Delete” will display on numbers stored using Code 40 when reviewing Code 41 entries. To delete a single number you have stored using Code 40, enter programming: press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code”...
- Page 9 the TEL phone port except those you want to block. This mode also works with your phone company’s voice mail but also blocks those phone numbers you have entered into the Blocked Callers List. Blocked callers will be immediately answered and after eight seconds get hung-up on. To enable this Mode, press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code”...
- Page 10 when the prompt for “Enter Code” displays enter 58, display shows function. To return to the default mode when the prompt for “Enter Code” displays, enter 59. “Unknown or Anonymous” Out of Area, Private and X Code 72 If you want to have an answer machine or your voice mail to take these types of calls and not ring your phone connected to the DPB you can program in Code 72 (OPX override).
- Page 11 for “Enter Code” displays enter 82, then enter the Start time of day Ex. 1700, 5:00pm, display shows function. Next, when the prompt for “Enter Code” displays enter 83, then enter your End time of day Ex. 0645, 6:45am, display shows function. Full Day After Hours Mode can be enabled when both Code 82 and Code 83 are the same number.
- Page 12 Global Block Method Code 97#* If you want to block all callers and invite only specific numbers, you can use Code 97 # * to disable the default Global Invited List and create your own invited call list. To enable this feature, press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code”...
- Page 13 56. Code 98 [number] * Delete specified number 57. Code 99 # * DIGITONE DEFAULT On reset, operating codes return to default list 58. Last Call Remote Entry Code * 1 # Invite, Code * 2 # Block, Code * 3 # VIP...
- Page 14 Next, when the prompt for “Enter Code” displays again, enter 99 # *. This fully resets the DPB to Digitone Default settings from the factory. “I have program blocked an area code with number but the caller is not being blocked.”...
- Page 15 DPB Compatibility * Digitone’s ProSeries Blocker works with all makes of analog telephony equipment and on all U.S. Domestic and Foreign standard 2-wire telephone lines with FSK/DTMF (ETSI) Caller ID, DSL, FIOS, Cable Modems and VoIP Digital services using (ATA) adapters from Skype™, Vonage™, Ooma™ or Magic Jack™.
- Page 16 1-877-610-5693 to obtain a Return Merchandise Authorization (RMA). The purchaser would then put this code on the exterior of the package shipped to Digitone. Any unit returned without this code will be refused and returned at sender's expense. Product should be shipped freight prepaid along with evidence...