RS-WP1WT SERVICE MANUAL CD PORTABLE SYSTEM RS-WP1WT CD PORTABLE SYSTEM RS-WP1 STANDBY STANDBY/ON Areas suffix BAND J -------------------------- U.S.A TIMER CLOCK TIMER ON/OFF STAND BY/ON SLEEP DOWN PROGRAM RANDOM AUTO PRESET REPEAT TUNER TAPE BAND FM MODE REVERSE MODE MULTI CONTROL...
Page 2
RS-WP1WT 1. This design of this product contains special hardware and many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be performed by qualified personnel only.
RS-WP1WT Important for Laser Products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam.
RS-WP1WT Preventing static electricity 1.Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
RS-WP1WT Disassembly method Removing the front panel assembly / rear panel assembly (See Fig.1) Remove the nine screws A attaching the rear panel assembly on the back of the body. Pull out the front panel assembly and the rear panel assembly.
Page 6
RS-WP1WT Joint a Joint a Removing the function switch board (See Fig.4) Function switch board Prior to performing the following procedures, remove CN921 the rear panel assembly. Disconnect the card wire from connector CN921 on the function switch board. Remove the two screws D and move the function switch board in the direction of the arrow to disengage the two joints a.
Page 7
RS-WP1WT Removing the LCD board (See Fig.7 and 8) LCD board Prior to performing the following procedures, remove the rear panel assembly and the function switch Bracket board. Remove the four screws E attaching the bracket. Disconnect the card wire from connector CN421, CN422 and the wire from CN913 on the LCD board respectively.
Page 8
RS-WP1WT Removing the main board / sub (1) board Rear panel assembly / sub (2) board (See Fig.11 to 13) Prior to performing the following procedures, remove the rear panel assembly, the CD mechanism assembly section and the LCD board.
Page 9
RS-WP1WT Removing the remocon board (See Fig.14) Remocon board Prior to performing the following procedure, remove LCD board the rear panel assembly. CN913 Remove the screw M attaching the remocon board and disconnect the wire from connector CN913 on the LCD board.
Page 10
RS-WP1WT Removing the power board (See Fig.16 to 18) CN103 Prior to performing the following procedures, remove the rear panel assembly. CN102 Power board Disconnect the wire from connector CN101, CN102 and CN103 on the power board. Remove the four screws O attaching the power board.
Page 11
RS-WP1WT Removing the connection board (See Fig.19) Prior to performing the following procedures, remove the rear panel assembly. Disconnect the wire from connector CN102 on the power board. Remove the two screws P and pull out the connection board. Connection board CN112 Fig.19...
Page 12
RS-WP1WT <CD mechanism assembly section> CD mechanism cover Prior to performing the following procedures, remove the rear panel assembly and the CD mechanism assembly section. Removing the CD mechanism assembly (See Fig.22 to 26) CAUTION: Prior to disconnecting the flexible wire...
Page 13
RS-WP1WT Removing the CD servo board (See Fig.27) FW616 FW626 Prior to performing the following procedure, remove the CD servo assembly. Remove the four screws S retaining the CD servo board. OPEN / CLOSE switch board Unsolder FW616 where the wire extending from the OPEN / CLOSE switch board is soldered.
Page 14
RS-WP1WT <Cassette mechanism section> Cassette mechanism Removing the playback / recording & eraser head (See Fig. 1 to 3) While shifting the trigger arms seen on the right side of the head mount in the arrow direction, turn the flywheel R in counterclockwise direction until the Flywheel R head mount has gone out with a click (See Fig.
Page 15
RS-WP1WT Removing the head amplifier & mechanism control board (See Fig. 4) Remove the cassette mechanism assembly. Belt Disconnet the flexible wire from connctor CN31 to CN32 Main motor the flexible board. assembly After turning over the cassette mechanism assembly, remove the three screws A retaining the head amplifier &...
Page 16
RS-WP1WT Removing the flywheel (See Fig. 7 and 8) Remove the head amplifier & mechanism control P.C. board. Flywheel R Flywheel L Remove the main motor assembly. After turning over the cassette mechanism, remove the two slit washers 1 and fixing the capstan shafts R and L, and pull out the flywheel R and L respectively from behind the cassette mechanism.
RS-WP1WT Adjustment method Tuner section Measuring devices necessary for adjustment Voltage input to the tuner ......+B: DC 5.7 V 1. Low-frequency oscillator VT: DC 12 V It must have the ability to output 600ohm from 0 dBs Standard measuring output ..26.1 mV (0.28 V)/3ohm at an oscillation frequency of 20 Hz-50 Hz.
Page 18
RS-WP1WT Location of parts to be adjusted Cassette handling mechanism Cassette handling mechanism (reverse side) Head for recording, playing and erasing the tape Head azimuth adjusting Head azimuth adjusting screw (fast-forward) screw (rewind) CN31 Head for recording, Head azimuth adjusting...
Page 19
RS-WP1WT Adjustment of cassette handling mechanism Items Condition Method for adjustment Standard Parts to be and confirmation value adjusted Confirmation Test tape: VT-703 (10 kHz) (1) Play back the VT-703 test tape. Maximum Adjust the of head angle Measuring output terminal:...
Page 20
RS-WP1WT Standard values for confirmation of electronic performance Items Condition Method for adjustment Standard Parts to be and confirmation value adjusted Erasing Fast-forward and Load the test tape (AC-514 for TYPE II, TYPE II: 110 current rewind direction: AC-225 for TYPE I) into the tape...
RS-WP1WT Flow of functional operation until TOC read Check Point Slider turns REST Play Key Power ON Confirm that the voltage at the pin3 SW ON. of CN612 is "H"\"L"\"H". Automatic tuning of TE offset Check that the voltage at the...
RS-WP1WT Replacement of laser pickup Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to Turn off the power switch and, disconnect the clean the lens with a alcohol soaked cotton power cord from the ac outlet.
Page 23
RS-WP1WT Description of major ICs LA4905 (IC101) : Power amp IC 1. Terminal layout 2. Block diagram Vcc(SW) STBY Switching Standby SW regulator block Ripple H.L.S. SW B filter drive A B C D SW E H.L.S. : SW OUT1...
Page 25
RS-WP1WT KIA78R06PI(IC381) US 6V 1. Terminal layout 2. Block diagram V IN 1 V 0 BANDGAP REFERENCE PROTECTION OUTPUT ON/OFF 1 2 3 CONTROL Control OVERHEAT PROTECTION KIA78R08PI(IC301) SW 8V REGULATOR 1. Terminal layout 2. Block diagram V IN 1 V 0...
Page 27
RS-WP1WT LC75342 (IC501) : E. volume 1. Terminal layout 2. Block diagram LVref CONTROL CIRCUIT LOGIC CIRCUIT INTERFACE CONTROL RVref CIRCUIT 3. Pin function Function Function Symbol Symbol Serial data and clock input for IC control Input signal connections Chip enable...
Page 28
RS-WP1WT MN101C38CHX (IC901) : System controller Pin No. Symbol Function COM 3~0 FL grid control signal output VLC 3~1 Power supply +5V 9,10 OSC2,1 Oscillation terminal (8MHz) Connect to GND 12,13 XI,XO Sub clock (32.768kHz) MMOD Connect to GND VREF-...
Page 29
RS-WP1WT MN35530 (IC601) : Digital servo & processor 1. Terminal layout 2. Pin function Symbol Function Symbol Function DVD3V Power supply ADPVCC Vcc for A/D input Data input DSLF Loop filter pin for DSL Data input Bias pin for DSL input...
Page 30
RS-WP1WT MN101C30AHY (IC602) : CD micon 1. Terminal layout 2. Pin function Symbol Function Symbol Function Connect to GND DOOR Door open/close sw detection input Connect to GND O MUTE Muting output Connect to GND DMUTE Digtal mute output Connect to GND...
Page 33
RS-WP1WT M11L1644SA-50T (IC605) : D RAM 1. Terminal layout 2. Pin Function Symbol Function VSS1 A0-A10 Address Input Low Address strove Column Address Strove Write enable Input Output Enable Input DQ0-DQ3 Data in/out VCC, VCC1 Power Supply (+3.3V) VSS, VSS1...
Page 34
RS-WP1WT TA2104AN(IC1) : RadioTuner 1. Terminal layout & Block diagram FM RFout RF V CC AM RFin FM OSC AM OSC OSC OUT ST LED IF REQ DET OUT LPF1 LPF2 BUFF DECODE BUFF DIVIDE BUFF LEVEL BUFF 1 / 8...
Page 35
RS-WP1WT VICTOR COMPANY OF JAPAN, LIMITED AUDIO & COMMUNICATION BUSINESS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan No.20943 200105...
RS-WP1WT PARTS LIST [ RS-WP1WT ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J ----------------------------- U.S.A. - Contents - Exploded view of general assembly and parts list 3- 3 Cassette mechanism assembly and parts list...
Page 38
RS-WP1WT Exploded view of general assembly and parts list Block No. Switch board LCD board AUX board Function amplifier CD door board switch board Input board CD board Optical digital out board Tuner board Remocon board Headphone jack board Power...
Page 39
RS-WP1WT Parts list (General assembly) Parts list (General assembly) Block No. M1MM Block No. M1MM Item Parts number Parts name Q'ty Description Area Item Parts number Parts name Q'ty Description Area LV10484-002A FRONT CABI ASSY QYSBSF3010Z SCREW CD CHASSIS+SW PWB...
Page 40
RS-WP1WT Parts list (General assembly) Block No. M1MM Item Parts number Parts name Q'ty Description Area LV32701-001A STAND SUPPORT FMJA3001-00A ROD ANT ASS'Y VYH5012-002 LUG TERMINAL QYSDSP3008Z SCREW LV42244-001A ANT.HOLDER QYSBSF3010Z SCREW FOR ANT HOLDER LV42379-201A ANTENA HOLDER LV32539-001A LCD HOLDER...
Page 41
RS-WP1WT Parts list (General assembly) Block No. M1MM Item Parts number Parts name Q'ty Description Area QUQ412-0909CJ FFC WIRE FUNCTION-CD QUQ412-0920CJ FFC WIRE FUNCTION-TUNER QUQ412-0910DJ FFC WIRE FUNCTION-SLC QUQ412-1010DJ FFC WIRE FUNCTION-SLC QUQ412-1807CJ FFC WIRE FUNCTION-MICOM QUQ412-1707CJ FFC WIRE FUNCTION-MICOM...
Page 42
RS-WP1WT Cassette mechanism assembly and parts list Block No. SLC-S31M Grease = EM-30L =UD-24 =UD-24H2 =LEN-320M =JC-888B =MOBIL-1 The lower side Cassette switch board Head amplifier & mechanism board...
Page 43
RS-WP1WT Parts list (Cassette mechanism) Block No. M2MM Item Parts number Parts name Q'ty Description Area VKS1165-00J CHASSIS B.ASS'Y VKS2274-002 REEL GEAR VKW5286-002 B.T. SPRING VKS5559-001 PLAY IDLE GEAR VKS5597-00B BLIND VKW5296-001 EARTH SPRING SLC-RP1SVM HEAD MOUNT ASSY VKY3149-002 CASSETTE SP.
Page 44
RS-WP1WT Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area BS401 VYH5483-101 SPRING FOR UM-1 C5202 QTE1H28-475Z E CAPACITOR BS402 VYH5483-101 SPRING FOR UM-1 C5203 QETN1HM-105Z E CAPACITOR 1.0MF 20% 50V...
Page 45
RS-WP1WT Electrical parts list (Main board) Block No. 01 Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area L5351 QQL244K-100Z INDUCTOR R2701 NRSA63J-153X MG RESISTOR Q2101 2SC2412K/R/-X TRANSISTOR R2802 NRSA63J-472X MG RESISTOR Q2103 2SC2412K/R/-X TRANSISTOR...
Page 46
RS-WP1WT Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area R7209 NRSA63J-222X MG RESISTOR R7210 NRSA63J-102X MG RESISTOR R7251 NRSA63J-0R0X MG RESISTOR R7252 NRSA63J-183X MG RESISTOR R7254 NRSA63J-393X MG RESISTOR R7351 NRSA63J-472X MG RESISTOR...
Page 47
RS-WP1WT Electrical parts list (Micom board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area CN101 QGA2501C1-06 6P CONNECTOR C9045 NCB31HK-102X C CAPACITOR CN102 QGA2501C1-04 4P CONNECTOR C9046 NCB31HK-103X C CAPACITOR CN103...
Page 48
RS-WP1WT Electrical parts list (Micom board) Block No. 02 Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area R1102 QRE141J-2R2Y C RESISTOR 2.2 5% 1/4W R9050 NRSA63J-222X MG RESISTOR R1111 NRSA63J-152X MG RESISTOR R9051 NRSA63J-103X...
Page 49
RS-WP1WT Electrical parts list (CD servo board) Block No. 03 Item Remarks Item Remarks Parts number Parts name Area Parts number Parts name Area CN611 QGF1004F4-16 16PIN CONNECTOR D6301 1SS133-T2 SI DIODE CN612 QGA2001C1-06 6P PLUG ASSY D6302 1SS133-T2 SI DIODE...
Page 50
RS-WP1WT Electrical parts list (CD servo board) Block No. 03 Item Parts number Parts name Remarks Area R6401 NRSA63J-223X MG RESISTOR R6402 NRSA63J-333X MG RESISTOR R6403 NRSA63J-473X MG RESISTOR R6404 NRSA63J-393X MG RESISTOR R6405 QRZ9006-4R7X F RESISTOR 4.7 1/0W R6406...
Page 51
RS-WP1WT Electrical parts list (Tuner board) Block No. 04 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area QCSB1HK-5R6Y C CAPACITOR 5.6PF 10% 50V QRE141J-473Y C RESISTOR 47K 5% 1/4W QDYB1CM-103Y C CAPACITOR QRE141J-220Y C RESISTOR...
Page 52
RS-WP1WT Electrical parts list (Head amplifier & mechanism board) Block No. 05 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 101 NCS21HJ-821X C CAPACITOR IC 33 BU4094BCF-X C 102 NCS21HJ-221X C CAPACITOR L 301...
Page 53
RS-WP1WT Electrical parts list (Head amplifier & mechanism board) Block No. 05 Item Parts number Parts name Remarks Area R 315 NRSA63J-100X MG RESISTOR R 316 NRSA63J-223X MG RESISTOR R 317 NRSA63J-100X MG RESISTOR R 319 NRSA63J-152X MG RESISTOR R 322...
Page 54
Parts list (Accessories) Block No. M4MM Item Parts number Parts name Q'ty Description Area LVT0682-001B INST.BOOK BT-52004-1 WARRANTY CARD BT-51018-2 WARRANTY CARD BT-20044G WARRANTY CARD BT-20071B JVC CENTER LIST BT-51020-2 J=REGIST CARD LV32785-001A SHOULDER BELT QAL0325-001 AC ADAPTOR RM-SRSWP1J REMOCON 3-19...
Page 55
RS-WP1WT In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "...