Planet ICA-151 Quick Installation Manual
Dual mode cmos internet camera
Hide thumbs
Also See for ICA-151:
- User manual (48 pages) ,
- User manual (48 pages) ,
- Quick installation manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet ICA-151
Summary of Contents for Planet ICA-151
- Page 1 Dual Mode CMOS Internet Camera ICA-151 Version 1.1 Quick Installation Guide...
-
Page 2: Table Of Contents
1. PACKAGE CONTENTS ... 3 2. SYSTEM REQUIREMENTS ... 4 3. OUTLOOK ... 5 3.1 Front Panel ... 5 3.2 Rear Panel ... 6 4. Physical Installation ... 7 5. Setup Wizard Configuration ... 8 6. Cam Viewer Lite Installation ...15 Appendix A: Feature Listing for Cam Viewer ...19 Appendix B: Suggest Hardware / System Requirement ...20 Appendix C: Ordering Information for Cam Viewer Pro ...20... -
Page 3: Package Contents
1. PACKAGE CONTENTS 1 x ICA-151 ó 1 x Camera Stand ó 1 x Power Adapter ó 1 x CD-ROM ó 1 x Quick Installation Guide ó Please use the power adapter in this package. Using a power supply with a different voltage rating will damage and void the warranty for this product. -
Page 4: System Requirements
• Memory Size : 512 MB or above • VGA card resolution : 1024 x 768 or above • Network bandwidth: In VGA resolution mode, System Hardware minimum upload bandwidth is 1Mbps. Optional: • Sound Card • Microphone (for PC) • Speaker (for PC and ICA-151) -
Page 5: Outlook
3. OUTLOOK 3.1 Front Panel Microphone Status LED Description No power. Power on. Blinking The Power LED will blink during start up (15 ~ 20 sec). Camera is not capturing video. Blinking Camera is capturing video. LAN is not connected or camera is not sending/receiving data. Blinking Data is being transmitted or received via the LAN connection. -
Page 6: Rear Panel
Reset to manufacturer default valued and reboot. When pressed and held over 10 seconds, the settings of IP Camera will be set to the default values. Upon completion, the PWE LED will blink three times. Reset Bottom Panel of ICA-151... -
Page 7: Physical Installation
4. Physical Installation 1. Connect an Ethernet cable Connect one end of an Ethernet cable to the LAN port located on the IP camera’s rear panel and connect the other end to the network device (hub or switch). 2. Attach the external power supply Attach the provided power adapter to the IP camera’s connector labeled “PWR”... -
Page 8: Setup Wizard Configuration
5. Setup Wizard Configuration Initial setup should be performed by using the supplied Windows-based Setup Wizard as follows: 1. Insert the bundled Product CD disk into CD-ROM drive to launch the autorun program. 2. After the web page displayed, click the “Setup Wizard” hyperlink on the list to start the configuration process. - Page 9 4. After clicking the setup camera button, it will auto search for the IP Cameras on your network. Click on 5. The next screen below will list the IP Camera on your network. Select it from the list on the left side, the current settings table will be displayed on the right side.
- Page 10 6. The administrator login window will pop up. If the Administrator Name and Administrator Password have been set, you will be prompted to enter them. If using the default values, please enter “admin” for both the name and the pass- word.
- Page 11 8. You can choose “Fixed IP Address” or “Dynamic IP Address” here. Click on to continue. 1. Fixed IP Address is recommended, and can always be used. 2. Dynamic IP Address can only be used if your LAN has a DCHP Server.
- Page 12 10. The next screen below will display all details of the IP Camera. Click on continue if those settings are correct, or click on rect values. 11. In this confirmation window below, click on “OK” to confirm that you want to save the new settings.
- Page 13 12. After confirming, the wizard will start to save the new settings as below screen. 13. When the saving process is completed, the prompt window will be displayed as below screen. Click on “OK” to finish.
- Page 14 14. The setup wizard now is completed. Click on “Exit” to close the setup wizard. After modifications, you may now connect the IP camera with the new configuration via web browser.
-
Page 15: Cam Viewer Lite Installation
6. Cam Viewer Lite Installation The Cam Viewer Lite / Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Lite. Note 1. Insert the bundled Cam Viewer CD disk into the CD-ROM drive to launch the autorun program. - Page 16 3. The “Welcome to the InstallShield Wizard for Planet Cam Viewer Lite 1.0.3” will display on the screen, please click “Next”. 4. Please read the license agreement and then check “I accept the terms of the license agreement” if you are agreed and click “Next” to continue the installation...
- Page 17 5. Please key in user name and company name for which you want and click “Next” to continue installation. 6. Check the option “Complete”, all program features will be installed (Requires the most disk space) and click “Next” to continue installation.
- Page 18 7. “Ready to Install the Program” will appear to prompt you to start the installation. Please click “Install” to start. 8. Please click “No” to finish the Cam Viewer Lite installation. In above step, when Cam Viewer works with MBM5 (Motherboard Monitor 5), Cam Viewer will display CPU temperature and fan speed.
-
Page 19: Appendix A: Feature Listing For Cam Viewer
Appendix A: Feature Listing for Cam Viewer Software Version IP Camera Input Dual Monitor Smart Guard I/O Device Hotline Address Book Log Viewer Counting Application Remote Playback Server Concurrent Playback Counting Function Smart Search Remote Live Viewer Cam Viewer Lite Cam Viewer Pro 4 / 8 / 16 / 32 / 64 Unusual event... -
Page 20: Appendix B: Suggest Hardware / System Requirement
Appendix B: Suggest Hardware / System Requirement Total FPS ~600 Intel Core 2 Duo QX6800 4 GB Chipset of Intel 946 or 965 chip, Intel Chipset recommended Motherboard ATI Radeon 9200, nVIDIA GeForce FX-5200, VGA Card Intel 945/965 or above (ATI recommended) Ethernet 100Base-TX or Above, Gigabit LAN recommended Hard Disk...