Problems When Using The Auto Mcacc Setup; The Input Setup Menu - Pioneer Elite VSX-33 Operating Instructions Manual

Basic Setup
• If Reverse Phase is displayed, the speaker's wiring
(+ and –) may be inverted. Check the speaker
1
connections.
– If the connections were wrong, turn off the power,
disconnect the power cord, then reconnect properly.
After this, perform the Full Auto MCACC procedure
again.
– If the connections were right, select GO NEXT and
continue.
7 Make sure 'OK' is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings.
Again, try to be as quiet as possible while this is
happening. It may take 3 to 10 minutes.
8 The Auto MCACC Setup procedure is completed and
the Home Menu menu reappears automatically.
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC Setup.
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using The
Advanced MCACC menu on page 73 or The System Setup
and Other Setup menus on page 82.

Problems when using the Auto MCACC Setup

If the room environment is not optimal for the Auto
MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the
microphone) the final settings may be incorrect. Check
for household appliances (air conditioner, fridge, fan,
etc.), that may be affecting the environment and switch
them off if necessary. If there are any instructions
showing in the front panel display, please follow them.
• Some older TVs may interfere with the operation of
the microphone. If this seems to be happening,
switch off the TV when doing the Auto MCACC Setup.
Note
1 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase (dipole speakers, reflective
speakers, etc.), Reverse Phase may be displayed even if the speakers are properly connected.
2 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with
different size settings. You can correct the setting manually using the Manual speaker setup on page 82.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking
delay and room characteristics into account) and generally does not need to be changed.
• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend
adjusting the settings manually.

The Input Setup menu

You only need to make settings in the Input Setup menu
if you didn't hook up your digital equipment according to
the default settings (see Input function default and
possible settings on page 40). In this case, you need to
tell the receiver what equipment is hooked up to which
terminal so the buttons on the remote control
correspond to the components you've connected.
1
HOME MENU.
A Graphical User Interface (GUI) screen appears on your
TV. Use /// and ENTER to navigate through the
screens and select menu items. Press RETURN to
confirm and exit the current menu.
2
3
2
4
The default names correspond with the names next to the
terminals on the rear panel (such as DVD or VIDEO)
which, in turn, correspond with the names on the remote
control.
5
component.
For example, if your DVD player only has an optical
output, you will need to change the DVD input function's
Digital In setting from COAX-1 (default) to the optical
input you've connected it to. The numbering (OPT-1 to 3)
corresponds with the numbers beside the inputs on the
back of the receiver.
6
other inputs.
There are optional settings in addition to the assignment
of the input jacks:
• Input Name – You can choose to rename the input
Press RECEIVER on the remote control, then press
Select 'System Setup' from the Home Menu.
Select 'Input Setup' from the System Setup menu.
4.System Setup
A/V RECEIVER
a.Manual SP Setup
b. Input Setup
c. OSD Language
d. Network Setup
e. Other Setup
Exit Return
Select the input function that you want to set up.
Select the input(s) to which you've connected your
When you're finished, proceed to the settings for
function for easier identification. Select Rename to
do so, or Default to return to the system default.
4b.Input Setup
A/V RECEIVER
Input : DVD
Input Name : Rename
Input Skip : OFF
Digital In : COAX-1
HDMI Input : - - -
Component In : Comp-1
12V Trigger1 : OFF
12V Trigger2 : OFF
Exit Finish
04
39
En