Black & Decker PW1370DW Original Instructions Manual page 23

USE OF THE APPLIANCE (Fig. D)
CONTROLS
Starter device (13)
Set the starter switch on (ON/I) to:
a) start the motor (in models without TSS device);
b) set the motor ready to start (in models with TSS
device). If there is a pilot light on the starter device, it
should light up. Set the starter device switch on
(OFF/0) to stop the appliance. If there is a pilot light
on the starter device, it should go out.
f Water jet control lever (18).
Warning! - Danger!
During operation the appliance must be positioned as
shown in Fig. D. on a firm, stable surface.
Start-up (Fig D)
1. Turn on the water supply tap fully.
2. Release the safety catch (16).
3. Depress the gun trigger for a few seconds and start up
the appliance using the starter device (ON/I).
Warning! - Danger!
Before starting up the appliance check that it is receiving water
correctly; use of the appliance without water will damage it. Do
not cover the ventilation grilles when the appliance is in use.
TSS models
- In TSS models
(with automatic delivery flow cut-off system):
f when the gun trigger is released the dynamic
pressure automatically cuts out the motor;
f when the gun trigger is depressed the automatic
drop in pressure starts the motor and the pressure is
restored after a very slight delay;
f if the TSS is to function correctly, all gun trigger
releasing and depressing operations must be at
least 4-5 seconds apart.
To prevent damage to the appliance, do not allow it to
operate dry and check that it is properly supplied with
water. For models without TSS, to prevent damage to
the appliance due to an increase in water temperature,
do not cut off the jet of water for more than 5 minutes
with the appliance running. Beware of kickback force
when opening the trigger gun.
Stopping the appliance
1. Set the starter device switch on (OFF/0).
2. Depress the gun trigger and discharge the residual
pressure inside the hoses.
3. Engage the gun safety catch (16).
Restarting
1. Release the safety catch (16).
2. Depress the gun trigger and discharge the residual
air inside the hoses.
3. Set the starter device on (ON/I).
Storage
1. Switch the appliance off (OFF/0).
2. Remove the plug from the socket.
3. Turn off the water supply tap.
4. Discharge the residual pressure from the gun until
all the water has come out of the nozzle.
5. Drain and wash out the detergent tank at the end of
the working session. To wash out the tank, use clean
water instead of the detergent.
6. Engage the gun safety catch (16).
Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to
the surface while still dry.
When dealing with vertical surfaces work from the bottom
upwards. Leave the detergent to act for 1-2 minute but do
not allow the surface to dry. Starting from the bottom, use
the high pressure jet at a minimum distance of 30 cm. Do
not allow the rinse water to run onto unwashed surfaces.
In some cases, scrubbing with brushes is needed to
remove dirt. High pressure is not always the best solution
for good cleaning results, since it may damage some
surfaces. The finest adjustable nozzle jet setting or the
rotating nozzle should not be used on delicate or painted
parts, or on pressurised components (e.g. tyres, inflation
valves, etc.). Effective cleaning depends on both the
pressure and volume of the water used, to the same degree.
MAINTENANCE (Fig. E)
Any maintenance operations not covered by this chapter should
be carried out by an Authorized sales and service Centre.
¡Important! To ensure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be performed
by authorized service centers or other qualified organizations,
always using identical replacement parts. Unit contains no
user service able parts inside.
Caution! Always disconnect the plug from the power
socket before carrying out any work on the appliance.
Cleaning the nozzle
1. Disconnect the lance from the nozzle.
2. Remove any dirt deposits from the nozzle hole using
the tool (4).
Cleaning the filter
Inspect the intake filter (7) and detergent filter (if fitted)
before each use, and clean in accordance with the
instructions if necessary.
ENGLISH • 23