Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datavideo VP-840
Summary of Contents for Datavideo VP-840
- Page 1 4K HDMI DISTRIBUTION AMPLIFIER 1X4 VP-840 Instruction Manual...
-
Page 2: Table Of Contents
Table of Contents FCC COMPLIANCE STATEMENT ........4 WARNINGS AND PRECAUTIONS ........4 WARRANTY ..............5 ............5 TANDARD ARRANTY ............. 6 HREE ARRANTY DISPOSAL ..............6 INTRODUCTION ............. 7 ................ 7 EATURES CONNECTIONS AND CONTROLS ........8 ..............8 RONT ANEL .............. - Page 3 Further advice on the content of this manual or on the product can be obtained by contacting your local Datavideo Office or...
-
Page 4: Fcc Compliance Statement
This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. -
Page 5: Warranty
Warranty Standard Warranty • Datavideo equipment are guaranteed against any manufacturing defects for one year from the date of purchase. • The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty. -
Page 6: Three Year Warranty
PCIe Card are covered for 1 year. The three-year warranty must be registered on Datavideo's official website • or with your local Datavideo office or one of its authorized distributors within 30 days of purchase. Disposal For EU Customers only - WEEE Marking... -
Page 7: Introduction
The Datavideo VP-840 is an HDMI 1x4 Distribution Amplifier featuring the capability to repeat HDMI source to 4 displays simultaneously. The VP-840 supports data rate up to 18 Gpbs and resolutions of 4K2K@60Hz, and is compliant with HDMI 2.0 and HDCP 2.2. -
Page 8: Connections And Controls
Connections and Controls Front Panel Power LED Turned ON when power adapter is connected. Input LED Turned ON when an HDMI source player is connected. Output LED Turned ON upon connection of HDMI monitors. F/W Upgrade Connect the PC to this port for firmware upgrade. - Page 9 EDID for incoming HDMI source players. While connecting a new monitor to the VP-840 in mode 1 (Auto EDID Analysis Learning Mode), experiencing a short period of time without display might be expected. The VP-840 will do automatic EDID learning and generate the best Extended Display Identification Data (EDID) among all connected monitors.
-
Page 10: Rear Panel
HDMI monitor to output port 1 and set the VP-840 to mode 8 (EDID-8). Once the VP-840 is set to EDID-8, it will always learn the EDID information from output port 1. -
Page 11: Hardware Installation
Hardware Installation Follow the steps outlined below to set up your VP-840 system. Switch off all devices, including monitors. Connect the output ports of the VP-840 to the displays. Connect an HDMI source (such as a Blu-ray Disc player) to the VP- 840 HDMI IN. -
Page 12: Firmware Update
Windows PC EPConsole UI Firmware Upgrade Procedure 1. Connect the USB Upgrade port of the VP-840 to the PC via a mini- USB cable. The USB Upgrade port can be found on the front panel of the VP-840. - Page 13 3. Click the FILE button to browse the hard drive for the firmware file. Double click the *.H00 file to import the firmware file, which should automatically bring in the *.H01 and *.H02 files.
- Page 14 4. Press the F/W Upgrade button on the front panel of the VP-840 while connecting the 12V power adapter to the device. 5. Release the F/W Upgrade button approximately 5 seconds after the 12V power adapter is connected. 6. Click the Program MCU button (highlighted by a red rectangle...
- Page 15 7. The firmware update is complete as soon as “BANK0 BANK1 BANK2 OK” appears in the progress bar which is found at the bottom of the EP Console interface. 8. Power cycle the device to finish the firmware upgrade process.
-
Page 16: Frequently-Asked Questions
Frequently-Asked Questions This section describes problems that you may encounter while using the VP-840. If you have questions, please refer to related sections and follow all the suggested solutions. If problem still exists, please contact your distributor or the service center. -
Page 17: Dimensions
Dimensions All measurements in millimeters (mm) -
Page 18: Specifications
Specifications Interfaces Video Inputs HDMI Type A x 1 Video Outputs HDMI Type A x 4 EDID Mode Selection DIP Switch Power LED x 1, Input Signal x 1, Output Indicator Signal x 4 DC Jack 5.5 mm lock-type Power Supply 12 V / 0.5A Power Input FW Upgrade Mini USB Port x 1... - Page 19 YCbCr4:2:0 10 bits • 4K2K 30Hz YCbCr4:4:4 8 bits DTS-HD Master Audio, Dolby TrueHD, Dolby Audio Support Digital, DTS, DVD-Audio, LPCM, SACD, MPCM General Operating 0 °C to 40 °C (32 °F to 104 °F) Temperature Humidity 10% to 80% Dimensions (mm) 174.31 x 63.2 x 35 Weight...
-
Page 20: Service And Support
It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo.com for answers to DATAVIDEO WORLDWIDE OFFICES common questions, support requests or contact your local office below.