Page 2
No part of this document may be used for distribution, reproduction, transmission, transcription, storage in a data retrieval sys- ® tem, or translated into any language in any form by any means without the prior written permission of ARRI . If you are down- ®...
Content Dimensions ..............................3 Safety Information ............................6 Explanations of Warning Signs and Indications ............6 General Notes .
• Always follow all safety information for your own protection. objects. ® • Please contact a trained ARRI service technician to do any Explanations of Warning Signs and Indications service and maintenance not described in this manual Possible risk of injury or damage to equipment.
Maintenance and repair work is only to be Other accessories or spare parts may cause hazards, carried out by an authorized ARRI service center. damage the product or invalidate the warranty. Do not operate the product if the ambient tempera- Check all cables and devices for visible damage ture exceeds 45°...
In addition to regular visible checks ARRI recom- Never use the cables for transportation. Never hang mends that all electric components are checked for the product on its cables. electrical safety by a professional every 12 month. CAUTION! High voltage! Always disconnect the prod- Keep the protocol of the check.
The ARRI logo, the ARRI name and all other trade- Maintenance Information marks in this document pertaining to services or products by ARRI or its affiliates and subsidiaries are trademarks or li- •...
DMX512-A protocol or the fixture menu. gamut color mixing enables the rendition of all color shades, The L10 can be powered by AC power. Please find more de- making color filters dispensible. tailed information in the section “Power” on page 17.
DMX-control All functions of the L10 are controllable through DMX. The L10 is also fully RDM compatible and is equipped with a feedback channel for reporting all set parameters including system sta-...
Overview Stirrup Tilt lock Spigot Top latch Latch Focus knob Fixture menu Stirrup bracket Connectors Tilt lock lever Focus knob Safety catch Front view and back view, manual version...
Physical Installation To adjust the stirrup You need WARNING! Attach an approved safety-cable to • a Torx20 screw driver, secure the product against clamp or bracket failure. Lead the safety-cable through the stirrup and keep it • a 10 mm allen key and as short as possible.
Loose the mounting screw of the tripod or the appropriate fixing screw of the mounting clamp to pan the L10. Tighten the screw • Be aware of the maximum tilt angle 90° upwards and 90° to avoid unintended movement. Loose the tilt-lock to tilt the L10 downwards.
• Close the top latch. Make sure that the hook of the top latch Control options engages into the holding ring of the accessory. You can set up or control the L10 with the options listed in the DMX/RDM-interface table below: The L10 has a DMX/RDM-interface.
L10 with power must be located near connect the product electrically to ground (earth) the product and easily accessible so that the L10 can easily be when connected to AC power. The AC mains power disconnected from power.
Overview of the fixture menu FUNCT (3) The FUNCT button has two functions: • Normal operation: Switches between CCT and HSI mode (only ARRI L10-C). • Fixture menu open: Jump UP one menu level. ENTER (4) The ENTER button has three functions: •...
Page 19
IN CCT mode the L10 generates white light with optimized col- or rendition. In HSI mode the L10 generates colored light. If sat- uration is set very low, the L10 generates white light, but not with optimized color rendition.
Page 20
To set the fan mode To set the DMX address • Press the + / [up] or - / [down] button, until SETUP is displayed Set the fan mode using the fixture menu: left in the display. • Press the + / [up] or - / [down] button, until SETUP is displayed left in the display.
• Press the + / [up] or - / [down] button to select the DMX mode. Confirm the selected mode with the ENTER button. The DMX • HOLD: The last received DMX values are used until the L10 mode blinks three times for confirmation.
• Confirm with the ENTER button. The current operating Recent temperature hours are displayed (e.g. 501h). To display the recent temperature of the light engine: • Press the + / [up] or - / [down] button, until STATUS is dis- •...
Demo mode The L10 offers, depending on the model, up to 15 DMX modes. In demo mode the L10 calls up an endless loop with all features Use the 8 bit modes with basic DMX controllers like dimmer the L10 supports.
Pin 3 = Data + (hot). RGBW Pins 4 and 5 are not used by the ARRI L10 but are bridged be- Simple mode for controlling the overall intensity and the red, tween input and output sockets. These pins can therefore be...
To connect the data link • Connect the DMX data output from the controller to the data input (male XLR) of the L10. • Run the data link from the data output (female XLR) to the data input of the next product.
%. Only in CCT mode: Displays the recent color temperature when turning the CCT/HUE knob in K Only in HUE mode (only L10-C): Displays the recent hue when turning the CCT/HUE knob in ° (0-360°) Only in CCT mode:...
Status Messages From firmware-version 1.0 Note: The small, horizontal arrow in the displays indicates sub-menus. Press the ENTER button to access the sub-menus. Note: In setup and status mode the options keep available until another function is called up. All other modes return to the appropriate mode after 2 sec.
Fixture Menu From firmware-version 1.0 Note: The small, horizontal arrow in the displays indicates sub-menus. Press the ENTER button to access the sub-menus. Note: In setup and status mode the options keep available until another function is called up. All other modes return to the appropriate mode after 2 sec.
Software Version Label Shows the software version string from main, e.g. Main 1.66.1 Yes 16 2012 19:10:26 DMX Start Address DMX address Identify Flag -> physically fl ash the light, ARRI L10-C flashes Blue and all other Identify Service White...
This parameter is utilized to retrieve technical details of a fixture. ARRI L10 shows Product Detail ID List LED with PWM control A text description of up to 32 characters for the model type of the fixture. ARRI L10- Device Model Description C, ARRI L10 Daylight Tuneable or ARRI L10 Tungsten Tuneable...
Page 31
Command Description Lamp Hours Shows the actual lamp hours of the fixture Factory Defaults This command deletes all user parameters and sets the fixture to factory default Device Power Cycles Shows the power cycle value, counts every cold start (switch or power-up) Reset Device Fixture makes a software reset (warm start) and carries out a reboot Power state of the fixture, supported power states:...
ARRI Lighting Service Manager Please find information about the features and the functionality of the ARRI Lighting Service Manager in the user manual for the ARRI Lighting Service Manager, which can be downloaded with the ARRI Lighting Service Manager software-bundle from the...
If the fixture menu is working, error E.011 can be ignored. However, if the fixture menu Fixture menu module not be E.011 remains dark (no LED lights up) we recommend to contact the ARRI service. They can detected. then carry out detailed analyses.
Channel Value Percent Function DMX protocol V3.x is set as default. Use the ALSM to change Dimmer to DMX protocol V4.x. ARRI advises to reserve 4 DMX chan- → 0-255 0-100 closed open nels more for each fixture when using DMX protocol V3.x. This...
Page 35
Mode 2: 16 bit resolution per function Mode 3: Coarse / fine channel per function Each of the 256 coarse steps is divided in 256 fine steps. Use Channel Value Percent Function this mode when your lighting control desk does not support true 16 bit resolution.
ARRI L10-DT (Daylight Tuneable) Mode 1: 8 bit resolution per function From firmware-version 1.0 Channel Value Percent Function Dimmer Overview closed → open 0-255 0-100 8 bit, 1 channel 16 bit, 2 channels Coarse / fine, 2 chan- Color temperature CCT 5.000 K →...
Page 37
Mode 2: 16 bit resolution per function Mode 3: Coarse / fine channel per function Each of the 256 coarse steps is divided in 256 fine steps. Use Channel Value Percent Function this mode when your lighting control desk does not support true 16 bit resolution.
ARRI L10-C Mode 1: White & RGBW, 8 bit resolution per function From firmware-version 1.0 Channel Value Percent Function Dimmer Overview closed → open 0-255 0-100 8 bit, 1 channel 16 bit, 2 cannels Coarse/fine, 1-2 chan- Color temperature CCT 2.800 K →...
Page 39
Mode 2: White, 8 bit resolution per function Mode 3: White & HSI, 8 bit resolution per function Channel Value Percent Function Channel Value Percent Function Dimmer Dimmer closed → open closed → open 0-255 0-100 0-255 0-100 Color temperature CCT Color temperature CCT 2.800 K →...
Page 40
Mode 4: RGBW, 8 bit resolution per function Mode 5: HSI, 8 bit resolution per function Channel Value Percent Function Channel Value Percent Function Dimmer Dimmer closed → open closed → open 0-255 0-100 0-255 0-100 Intensity red 0% → 100% 0°...
Page 41
Mode 6: White & RGBW, 16 bit resolution per function Mode 7: White, 16 bit resolution per function Channel Value Percent Function Channel Value Percent Function Dimmer Dimmer closed → open closed → open 0-65535 0-100 0-65535 0-100 GN saturation Color temperature CCT 0-5.000 neutral / no effect...
Page 42
Mode 8: White & HSI, 16 bit resolution per function Mode 9: RGBW, 16 bit resolution per function Channel Value Percent Function Channel Value Percent Function Dimmer Dimmer closed → open closed → open 0-65535 0-100 0-65535 0-100 Color temperature CCT Intensity red 2.800 K →...
Page 43
Mode 10: HSI, 16 bit resolution per function Channel Value Percent Function GN saturation Channel Value Percent Function 0-10 neutral / no effect 11-20 full minus green Dimmer -99% → -1% 21-119 8-46 closed → open 0-65535 0-100 120-145 47-57 neutral / no effect 1% →...
Page 44
Mode 12: White, Coarse / fine channel per function Mode 13: White & HSI, Coarse / fine channel per function Channel Value Percent Function Channel Value Percent Function Dimmer coarse Dimmer coarse closed → open closed → open 0-255 0-100 0-255 0-100 0-255...
Page 45
Mode 14: RGBW, Coarse / fine channel per function Mode 15: HSI, Coarse / fine channel per function Channel Value Percent Function Channel Value Percent Function Dimmer coarse Dimmer coarse closed → open closed → open 0-255 0-100 0-255 0-100 0-255 0-100 Dimmer fine...
Page 46
Overview of typical CCT values as DMX values CCT values for the ARRI L10 models: L10-TT (Tungsten Tuneable) CCT- DMX-Value (8 bit) DMX-Value (16 bit) = 2.600 K Value = 3.600 K L10- L10-DT (Daylight Tuneable) 3.200 K 39.321 3.670 = 5.000 K...