1. Manuals
  2. Brands
  3. Pyle Manuals
  4. Security Sensors
  5. PHMD1
  6. Instruction manual

Pyle PHMD1 Instruction Manual

Treasure hunter bronze metal
Hide thumbs
Table of Contents

Advertisement

Quick Links

Treasure Hunter Bronze Metal
Detector
PHMD1
www.pyleaudio.com
Instruction Manual
This Metal Detector is a versatile and easy-to-use metal detector. It has higher
sensitivity and has the ability to differentiate between ferrous metals and nonferrous
metals. It is suitable for beginners.
Please read the manual carefully before using the unit.

Advertisement

Table of Contents
loading

Related Manuals for Pyle PHMD1

Summary of Contents for Pyle PHMD1

  • Page 1 Treasure Hunter Bronze Metal Detector PHMD1 www.pyleaudio.com Instruction Manual This Metal Detector is a versatile and easy-to-use metal detector. It has higher sensitivity and has the ability to differentiate between ferrous metals and nonferrous metals. It is suitable for beginners.

  • Page 2: Table Of Contents

    CONTENTS Specification Assembly Batteries Panel and Controller Quick-Start Field Operation Caution Trouble Shooting Guide Specification: • Single mode operation • No-motion Mode: As long as there is metal object around the search coil, the detector will have a response. • Adjusting DISCRIMINATION •...

  • Page 3: Assembly

    Assembly Assembly is easy and requires no special tools. 1. Align the plastic trapeziform raised part on the handle, with the trapeziform lower groove at the control box bottom (Figure.1).push the two parts tightly. Figure.1 2. Align the threaded bolts at the handle bottom, with the knobs under the control box, lock it with the bolts(Figure.2).

  • Page 4: Batteries

    Figure.4 Batteries Please use six AA alkaline batteries. 1. Press the “key” on the battery compartment in the direction of the arrow, pull out the battery compartment cover (Figure.5). Note: the word UP is engraved on the battery compartment, don’t mistake the direction. Figure.5 2.

  • Page 5: Panel And Controller

    3. Close the battery compartment cover, please note that the UP-side is facing up. 4. Six alkaline batteries may be used for more than 40 hours. If you do not plan to use the detector for a long time, remove the batteries. 5.

  • Page 6: Figure

     Wave the search coil properly, keep the angle between search coil and aluminum stem is about 140°. Please note improper backwards installation (Figure.8) Figure.8  Place the detector on a wooden or plastic table. Let the search coil hang over the edge exceeding the table edge more than 5 inches(15cm).

  • Page 7: Figure

    Figure.10  Adjust the Volume potentiometer, let you can hear the light hum tone, don’t adjust it too loud.  Once you adjust the “DISC” button, you should adjust the balance over again. In general, you should only press the Red Button to let the detector return to the balance state.
  • Page 8  Let other nonferrous metals approach the search coil, the meter pointer will deflect to the right, and the sound will turn louder. (Figure.12) Figure.12 6. Discriminate silver  Set the “DISC” knob to “MAX”. Adjust the balance to let the meter pointer points “0”and the detector sound a light hum tone.

  • Page 9: Knob

    Figure.14 7. Discriminate different metals approximately We take 5￠nickel coin and pull tab as an example to explain the approximate discrimination method.  Set the DISCRIMINATION to about “12:00” position (Figure.15). Adjust the balance to let the detector sound a hum tone, and the show is “0” Figure.15 ...

  • Page 10: Field Operation

    Field Operation Metal detector is used outdoors. There are too many metals indoors, and also all kinds of electrical equipments that will cause interference signals, so it’s not fit for using the metal detector. Field detection is more complicated, the composition of the detected regional soil, the component, size, shape and the oxidation degree of the underground metals will all affect the detection results.

  • Page 11: Caution

    Figure.16 Figure.17 When finding metal objects, you should move the search coil on the ground according to figure 16, In order to determine the metal position exactly. The nearer the search coil from the object, the more strong the response is. Figure.18 6.

  • Page 12: Trouble Shooting Guide

    1) Before detection every time, you should press Red Button to adjust balance, release the button when detecting, you should not press the Red Button while detecting. 2) The volume should be adjusted so that you can hear the sound, not adjust it too loud.
  • Page 13 Screw M3X8 Screw M3X12 Adhesive Sticker Right Arm Rest Support Support Arm Adjustment Knob View Meter Outer Stem Washer 3mm Washer Screw M3X8 Inner Stem Control Panel Lock Nut Interior Support Arm(Right Side) Lock Nut Exterior Nut M4 Look Nut Cover Screw M3X18 Bushing Screw M3X14...

Table of Contents