Table of Contents
Advertisement
Quick Links
HBM200/HBMX200
SERIES
*
*For use in Hazardous Locations Class I, Division 1, Groups C & D
SUBMERSIBLE BASIN MIXER
*
INSTALLATION AND SERVICE MANUAL
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # E-03-545 | Part # 5625-545-1 | © 2014 Pentair Pump Group, Inc. | 09/05 /14
Advertisement
Table of Contents
Summary of Contents for Pentair HBM 200 series
- Page 1 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # E-03-545 | Part # 5625-545-1 | © 2014 Pentair Pump Group, Inc. | 09/05 /14...
-
Page 2: Mixer Installation
WARNING: Severe injury may General Mixer Installation result from accidental contact Information with moving propeller. Keep Unpacking: clothing, hands and feet away Remove from carton. When Attention: from propeller any time power is un pack ing unit, check for connected to the mixer. This manual contains important concealed damage. -
Page 3: Mixer Maintenance
using two screwdrivers, slide the Electrical Connections: position of mixer mounting carbon assembly off by prying on brackets until desired mixing Make all connections from motor the retaining ring. action is achieved in the basin. to control panel to com ply with local codes. -
Page 4: Troubleshooting
Using a good quality dielectric Troubleshooting oil, lube the rubber material on the carbon seal assembly and Below is a list of troubles and press it on the shaft. Place the their probable causes: spring and the seal retainer on Insufficient mixing the shaft as removed. - Page 5 HBM200 Parts List Part Part Item Eng. No. Description Qty. Item Eng. No. Description Qty. 144240115 Cord Assembly 152120002 Propeller – Mixer 000640011 Spring – Bearing Adj. 152220001 Seal – Lip 4" 000650011 Bearing – Ball (Upper) 19100A004 Screw – Cap 5/16 SST x 3/4 000650271 Bearing –...
- Page 6 HBMX200 Parts List Part Part Part Item Eng. No. Description Qty. Item Eng. No. Description Qty. Item Eng. No. Description Qty. 22407C607 Cord Cap – 35 Ft. 526033065 Bracket – Mixer 001780041 Screw – Cap 5/16-18 05013A027 Screw – Set 5/16-18 21576A010 Seal –...
- Page 7 THIS PAGE INTENTIONALLY LEFT BLANK...
-
Page 8: Standard Limited Warranty
Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility. - Page 9 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # E-03-520 | Part # 5625-520-1 | © 2012 Pentair Pump Group, Inc. | 11/05/12...
-
Page 10: General Information
the bottom right of the box. The General Power ground lug should be fastened to a good driven earth ground by Information Supply one of the methods described in the National Electric Code. NEC Thank you for purchasing your WARNING: Do not attempt to does not permit using ground Hydromatic Basin Mixer Control... - Page 11 appropriate ter mi nal blocks in HBM (Pre December 2011) the control panel. c. Before connecting power to the control panel, make sure all con trol switches (e.g. H-O-A switch) and protective devices (e.g. breakers) are in the Off po si tion. Now connect power to the terminal block or the circuit break er as directed by the sche mat ic.
-
Page 12: Start-Up Operation
on hit the Menu button iii. Set 1-29 AMT; set to 2 Start-up until the pointer is above and follow instructions main menu. then set back to 0. Operation b. Use up and down key to iv. Set 3-02 speed in Hz; 1. - Page 13 ON TIME “On Time” adjustment “On Time” within range selected range selection Example dial positions shown: On Time 10 sec Off Time 18 sec “Off Time” adjustment within range selected “Off Time” range selection OFF TIME Dial Setting Timing Range Dial Setting Timing Range Dial Setting...
- Page 14 circuitry for moisture and heat 9. Check labels to verify they Seal sensor connections. have not been damaged. Failure 10. Lubricate enclosure hinges. Your mixer is equipped with temperature fail sensor thermostats Spare Parts List: Your mixer is equipped with a attached directly to the motor seal fail (moisture) sensor.
- Page 15 d. With the power off, check in the junction box may 4. Again read the amperage of motor heat sensor continuity. cause relays to energize each lead. intermittent ly. e. Check wiring of mixer to 5. Move each lead to the next con trol panel.
- Page 16 (Pre December 2011) 230V, 3 Phase, 60 Hz Wiring Schematic 230V-2.0HP 230 VAC, 3 PHASE, 60 HZ VFD10 175A 1x4 (133) MIXER_MOTOR 102A 102B 102C 102D L1-1 T1-1 T1-2 CUSTOMER 103A 103B 103C 103D SUPPLIED L2-1 T2-1 POWER T2-2 104A 104B 104C 104D...
- Page 17 (Pre December 2011) 460V, 3 Phase, 60 Hz Wiring Schematic 460V-2.0HP 460 VAC, 3 PHASE, 60 HZ VFD10 175A 1x4 (133) MIXER_MOTOR 102A 102B 102C 102D L1-1 T1-1 T1-2 CUSTOMER 103A 103B 103C 103D SUPPLIED L2-1 T2-1 T2-2 POWER 104A 104B 104C 104D...
- Page 18 (Post December 2011) 230V, 3 Phase, 60 Hz Wiring Schematic...
- Page 19 (Post December 2011) 460V, 3 Phase, 60 Hz Wiring Schematic...
- Page 20 HBMX (Post December 2011) 230V, 3 Phase, 60 Hz Wiring Schematic...
- Page 21 HBMX (Post December 2011) 460V, 3 Phase, 60 Hz Wiring Schematic...
- Page 22 THIS PAGE INTENTIONALLY LEFT BLANK...
- Page 23 THIS PAGE INTENTIONALLY LEFT BLANK...
- Page 24 Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.