Table of Contents
Advertisement
Quick Links
Coldroom TectoCell Compact 80
Coldroom and deep-freezing room
TectoCell Compact 100
Please read this assembly manual carefully prior to
assembling or commissioning the unit. Your specialist
refrigeration technician will be glad to explain the
functions of the coldroom and instruct you in its operation.
All work on the device and the refrigeration unit must be
carried out by an authorised refrigeration specialist.
General notice (liability): the details of this technical documents serve for description. Consents regarding the availability of certain features or
regarding a certain purpose always require a special written agreement.
Page 1 GB
Assembly and
Operating Manual
6026901-02 GB
Any work on the electrical parts of the coldroom must be
done by qualified electricians. The plug must be separated
from the socket and protected from reinsertion and/or
the power supply must be turned off at the source and
protected from being switched on while work is in progress.
GB
Right reserved to make technical changes!
Advertisement
Table of Contents
Summary of Contents for Viessmann TectoCell Compact 80
- Page 1 Coldroom TectoCell Compact 80 Coldroom and deep-freezing room TectoCell Compact 100 Assembly and Operating Manual 6026901-02 GB Please read this assembly manual carefully prior to Any work on the electrical parts of the coldroom must be assembling or commissioning the unit. Your specialist done by qualified electricians.
-
Page 2: Table Of Contents
Table of contents Gerneral notes Area of validity Extract from the conditions of guarantee Supplied condition Unpacking and Handling Assembly of the coldroom Disposing of the coldroom Preliminary work Compensation for uneven floor Coldrooms with flooring ventilation (Coldroom temperature under - 5°C) Coldrooms without flooring ventilation Coldroom assembly Connecting the coldroom panels... -
Page 3: Gerneral Notes
- Any damage must be noted immediately on the freight papers and these must be sent to Viessmann. Please note „Conditions in case of damage“! As a rule, Caution! the „General Condtions for Transport Damage and Hidden Transport Damage”... -
Page 4: Assembly Of The Coldroom
An electrical floor heating can be used instead of floor plating. Installation outdoor The Viessmann coldrooms are suitable for installation outdoor - but this must be done under a protective roof. (local construction measures) lf coldrooms are installed outdoor, discolouring of the paint may occur as a result of UV radiation. -
Page 5: Preliminary Work
2. Preliminary work Compensation for uneven floor 051-4-0/1 (Please note accompanying coldroom drawing) Mark shape of coldroom on floor with chalk. Coldrooms with flooring ventilation (Coldroom temperature under - 5°C) The flooring gratings are laid loosely at a distance of 200 to 300 mm from each other. -
Page 6: Coldroom Assembly
3. Coldroom assembly Important! The panels are provided with seal at the plant - do not damage! When transporting or moving the elements, do not grasp them by the overlap of the spring side or in their groove. Always hold the elements at the bot tom, to prevent the sheets from coming loose. -
Page 7: Assembly Of The Flooring Panels
Assembly of the flooring panels Flooring panels with stainless steel covering plate: The flooring panels are equipped with a sealing gasket (R) on the tongue side at the underlapping point. Ensure that this seal is not damaged. For flooring panels with one or two sided connections, fill the points marked on the drawing with sealant. -
Page 8: Assembly Of The Wall Panels
Assembly of the wall panels Clean the interior flooring panel in the area of the interior wall plating C with isopropanol. Adhere the enclosed sealing gasket (D) to the cleaned edge of the interior flooring plate. Remove the protective foil from the sealing gasket. Begin the wall assembly with the corner panels. -
Page 9: Removing Transportation Securing Plates
Removing transportation securing plates The magnetic gasket seal on the door is protected from mechanical damage by means of the securing plates (M). Prior to adjusting the door and/or activation of the coldroom, these must be removed. Adjusting the hinges Important! lf the magnetic gasket profile does not fit properly around the whole periphery of the door and the sealing... -
Page 10: Mechanical Works On The Door Or The Hatch
3.10 Mechanical works on the door or the hatch Important! For door and view hatch panels, mechanical work in the marked area (e.g. drilling, sawing) is prohibited. This applies both for the exterior and for the interior. Electrical components have been foamed in here. Danger to life may result from damaging the integrated electrical wires! 3.11 Coldroom without flooring panels... -
Page 11: Electrical Connections
4. Electrical connections Attention! Note! Work on the electrical network and protective measures If the temperature drops and reaches a level of (FI-safety switch) is to be done by a specialist electrician approx. 0°C, the thermal actuator in the distributor according to the current regulations (EN, ISO, VDE...) and box of heated doors switches on the window and conditions of the local energy supply company. -
Page 12: Miscellaneous
5. Miscellaneous Replacement of cylinder lock on rotary handle lock Unscrew the stud bolt (K) from the side of the outside handle using a 2.5 mm hexagon key (L). Insert key (H) into the cylinder (F), turn to the horizontal position with ¼... -
Page 13: Commissioning
(e.g. ETOLIT, Fa. 1000 30.000 Viessmann). Seal the stainless steel surface with an appropriate material for stainless steel (e.g. Chromadur, Fa. Assindia-Chemie or Inox Top, Fa. Viessmann). Deactivation Pay attention to the product information! -
Page 14: Energy Saving And Storage Of Refrigerated Products
7. Energy saving and storage of refrigerated products Notes on energy savings Storing refrigerated goods Do not install coldrooms or refrigeration units near heating When the desired temperature of storage is achieved sources; if the ambient temperature is too high, this will in the coldroom, the refrigerated goods can be cfrome the refrigeration unit to run to activate too often. -
Page 15: Gb Right Reserved To Make Technical Changes
General notice (liability): the details of this technical documents serve for description. Consents regarding the availability of certain features or regarding a certain purpose always require a special written agreement. Page 15 GB Right reserved to make technical changes! - Page 16 Austria Latvia Viessmann Kühlsysteme Austria GmbH Viessmann Refrigeration Systems Latvia fi liále Telephone +43 72 35 66367-0 Telephone +371 6782 8449 o ce_vk_at@viessmann.com info.lv@viessmann.com www.viessmann.at www.viessmann.com Belgium Netherlands Viessmann Nederland B.V. Viessmann Nederland B.V. Telephone +31 10 4584444 Telephone +31 10 4584444 info-ref-be@viessmann.com...