About this Manual ......................................1 Overview ..................................................1 Manual Conventions ............................................. 2 References ........................................2 Technical Support ......................................2 Wasp Website Support ............................................2 Telephone Technical Support ..........................................2 About the Reader ......................................3 Programming the Reader ....................................3 Configuration Methods ............................................3 SETUP ........................................
Page 4
1D Symbologies..................................79 1D Code Selection ......................................79 DISABLE ALL SYMBOLOGIES ..............................80 CODE EAN/UPC .................................... 81 Coupon Control ..........................................81 UPC-A ..............................................82 UPC-A Enable/Disable ........................................82 UPC-A Check Character Transmission ..................................82 Expand UPC-A to EAN-13 ......................................83 UPC-A Number System Character Transmission ..............................83 WDI4600...
Page 5
UPC-A 2D Component ........................................84 UPC-E ......................................84 UPC-E Enable/Disable ........................................84 UPC-E Check Character Transmission ..................................85 UPC-E 2D Component ........................................85 Expand UPC-E to EAN-13 ......................................86 Expand UPC-E to UPC-A .......................................86 UPC-E Number System Character Transmission ..............................87 GTIN FORMATTING ..................................87 EAN 13 (JAN 13) ................................... 88 EAN 13 Enable/Disable .........................................88 EAN 13 Check Character Transmission ...................................88 EAN-13 Flag 1 Character .......................................89...
Page 6
Code 11 Enable/Disable ......................................146 Code 11 Check Character Calculation .................................. 146 Code 11 Check Character Transmission ................................147 Code 11 Length Control ......................................147 Code 11 Set Length 1 ......................................... 148 Code 11 Set Length 2 ......................................... 149 GS1 DATABAR™ OMNIDIRECTIONAL ............................150 WDI4600...
Page 8
Aiming Duration Time ............................................. 231 Flash On Time ..............................................232 Flash Off Time ..............................................233 Multiple Labels Ordering by Code Symbology ..................................234 Motion Features ......................................236 Motionless Timeout ............................................236 TECHNICAL SPECIFICATIONS..............................237 Imager Labeling ......................................241 Standard Cable Pinouts .....................................242 WDI4600...
Page 9
LED and Beeper Indications ..................................243 Error Codes ........................................244 STANDARD DEFAULTS ................................245 SAMPLE BARCODES..................................257 KEYPAD ......................................261 SCANCODE TABLES ..................................263 Control Character Emulation ..................................263 Single Press and Release Keys ........................................263 Interface Type PC AT PS/2, USB-Keyboard or USB-Keyboard for APPLE ....................264 Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode ......................266 Digital Interface ......................................268 IBM31xx 102-key ......................................269...
Chapter 1 Introduction About this Manual This Product Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming, maintenance and specifications. The Quick Reference Guide (QRG) and other publications associated with this product are downloadable free of charge from the website listed on the back cover of this manual. Overview Chapter 1, (this chapter) presents information about manual conventions, and an overview of...
Telephone Technical Support If you do not have internet or email access, you may contact Wasp Barcode Technologies technical support at 214-547-4100, or check the back cover of this manual for more contact information.
About the Reader Introduction About the Reader Typically, units are factory-programmed for the most common terminal and communications settings. If you need to modify any programmable settings, custom configuration can be accomplished by scanning the programming bar codes within this guide. Advancements in the LED technology used in the imager-based readers significantly improve the illumination of the target field of view, resulting in higher scan efficiency.
Page 14
Introduction Programming the Reader NOTES WDI4600...
Setup Unpacking Check carefully to ensure the reader and any accessories ordered are present and undamaged. If any damage occurred during shipment, contact Wasp Barcode Technologies Technical Support. Information is shown on page 2 KEEP THE PACKAGING. Should the unit ever require service, it should be returned in its original shipping container.
Terminal) to supply reader power, use the approved power supply (AC Adapter). Plug the AC Adapter barrel connector into the socket on the RS-232 cable connector and the AC Adapter plug into a standard power outlet. Figure 2. RS-232 Connection WDI4600...
Page 17
Installing the Interface Cable Setup Keyboard Wedge Connection The Keyboard Wedge cable has a ‘Y’ connection from the reader. Connect the female to the male end from the keyboard and the remaining end at the keyboard port at the terminal/PC. Reference Figure 3 Figure 3.
Some interfaces require the scanner to start in the disabled state when powered up. If additional scanner configuration is desired while in this state, pull the trigger and hold it for five seconds. The scanner will change to a state that allows programming with barcodes. WDI4600...
Page 19
Interface Selection Setup Table 1. Available Interfaces RS-232 FEATURES RS-232 standard interface Select RS232-STD $P,HA12,P(CR) RS-232 Wincor-Nixdorf Set RS-232 Select RS232-WN Interface Features $P,HA13,P(CR) starting on page 19 RS-232 for use with OPOS/UPOS/JavaPOS Select RS-232 OPOS $P,HA47,P(CR) USB Com to simulate RS-232 standard interface Select USB-COM-STD USB-OEM FEATURES...
Page 20
80, 90 & 95 w/Alternate Key starting on page Select KBD-AT-ALT $P,HA10,P(CR) Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Select KBD-AT-ALT-NK $P,HA28,P(CR) PC/XT w/Standard Key Encoding Select KBD-XT $P,HA14,P(CR) Keyboard Wedge for IBM Terminal 3153 Select KBD-IBM-3153 WDI4600...
Page 21
Interface Selection Setup KEYBOARD (continued) FEATURES $P,HA15,P(CR) Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make only key- board Select KBD-IBM-M $P,HA16,P(CR) Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break key- board Select KBD-IBM-MB Set KEYBOARD $P,HA1B,P(CR) WEDGE Keyboard Wedge for DIGITAL Termi-...
Software Version Transmission The software version of the device can be transmitted over the RS-232 and Keyboard interfaces by scanning the following label. RevA Transmit Software Version WDI4600...
Customizing Configuration Settings Setup Resetting the Product Configuration to Defaults Restore Custom Defaults If you aren’t sure what programming options are in your imager, or you’ve changed some options and want to restore the Custom Default Configuration that may have been saved in the scanner, scan the Restore Custom Default Configuration barcode below.
Chapter 3 Configuration Using Barcodes This and following sections provide programming barcodes to configure your reader by changing the default settings. For details about additional methods of programming, see "Configuration Methods" on page You must first enable your reader to read barcodes in order to use this Setup, starting on page 5 section.
Page 26
By default, the handheld will decode barcode labels only when they are close to the center of the aiming pattern. This allows the handheld to accu- rately target labels when they are placed close together, such as on a pick Pick Mode, starting on page sheet. See WDI4600...
Global Interface Features Enter/Exit Programming Mode GLOBAL INTERFACE FEATURES The following interface features are configurable by all interface types. Host Commands — Obey/Ignore This option specifies whether the reader will obey or ignore host commands. When set to ignore, the reader will ignore all host commands except for those necessary for: •...
Page 28
Enter/Exit Programming Mode Global Interface Features NOTES WDI4600...
RS-232 INTERFACE on page 20 on page 21 on page 21 ARITY on page 22 ANDSHAKING ONTROL on page 23 Use the programming barcodes in this section if modifications to the standard RS-232 interface settings are necessary to meet your system’s requirements. Additional settings which apply to both the RS-232 and USB interfaces are available in the next section, "RS-232/USB-Com Interfaces"...
RS-232 Interface Enter/Exit Programming Mode Data Bits This parameter allows the reader to interface with devices requiring a 7-bit or 8-bit ASCII protocol for sending and receiving data. $CR2DA00(CR) 7 Data Bits $CR2DA01(CR) DEFAULT 8 Data Bits Stop Bits Set the number of stop bits to match host device requirements. See page 206 for more information on this feature.
Parity This feature specifies parity required for sending and receiving data. Select the parity type according to host device requirements. See page 206 for more information. $CR2PA00(CR) DEFAULT Parity = None $CR2PA01(CR) Parity = Even $CR2PA02(CR) Parity = Odd WDI4600...
RS-232 Interface Enter/Exit Programming Mode Handshaking Control page 206 for more information about this feature. $CR2HC00(CR) DEFAULT Handshaking Control = RTS $CR2HC01(CR) Handshaking Control = RTS/CTS $CR2HC02(CR) Handshaking Control = RTS/XON/XOFF $CR2HC03(CR) Handshaking Control = RTS On/CTS $CR2HC04(CR) Handshaking Control = RTS/CTS Scan Control Product Reference Guide...
RS-232/USB-COM INTERFACES NTERCHARACTER ELAY on page 25 ASCII BEL on page 25 OT ON on page 26 ACK NAK O PTIONS on page 26 ACK C HARACTER on page 27 NAK C HARACTER on page 27 ACK NAK T IMEOUT ALUE on page 28 ACK NAK R...
RS-232/USB-Com Interfaces Enter/Exit Programming Mode Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments.
RS-232/USB-Com Interfaces Enter/Exit Programming Mode ACK Character This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII characters or any hex value from 0 to 0xFF can be selected. See page 208 for more information. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal Data Bits operation of these characters.
Select ACK NAK Retry Count Setting scanning the ENTER/EXIT barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 003 = 3 Retries DEFAULT WDI4600...
RS-232/USB-Com Interfaces Enter/Exit Programming Mode ACK NAK Error Handling This feature specifies the method the reader uses to handle receive errors detected while waiting for an ACK character from the host. $CR2EH00(CR) DEFAULT ACK NAK Error Handling = Ignore Errors Detected $CR2EH01(CR) ACK NAK Error Handling = Process Error as Valid ACK Character...
8-bit data is not recognized when the option has been set as 7 Data Bits. page 213 in “References” for more information on setting this feature. $CR2EC Select Enable Character Setting 0x45 = Enable Character is ‘E’ DEFAULT WDI4600...
KEYBOARD SETTINGS OUNTRY on page 32 ONTROL HARACTERS on page 36 EDGE UIET NTERVAL on page 37 NTERCODE ELAY on page 37 TATE on page 38 UMLOCK on page 38 USB K EYBOARD PEED on page 39 USB K EYBOARD UMERIC EYPAD on page 40...
Mode feature description. Country Mode = Croatia $CKBCO0E(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Czech Republic $CKBCO03(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Denmark WDI4600...
Page 43
Keyboard Settings Enter/Exit Programming Mode Country Mode (continued) $CKBCO04(CR) Country Mode = France $CKBCO13(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = French Canadian $CKBCO05(CR) Country Mode = Germany $CKBCO0D(CR) Supports only the interfaces listed in the Country Mode feature description.
Page 44
Mode feature description. Country Mode = Portugal $CKBCO10(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Romania $CKBCO0F(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Slovakia WDI4600...
Page 45
Keyboard Settings Enter/Exit Programming Mode Country Mode (continued) $CKBCO09(CR) Country Mode = Spain $KBCO0A(CR) Country Mode = Sweden $CKBCO0B(CR) Supports only the interfaces listed in the Country Mode feature description. Country Mode = Switzerland Product Reference Guide...
Special keys are located from 00 to 0x1F and characters from 0x80 to 0xFE are intended as an extended ASCII table (see "Microsoft Windows Codepage 1252" on page 271). $CKBSC00(CR) DEFAULT Wedge Send Control Characters = 00 $CKBSC01(CR) Wedge Send Control Characters = 01 $CKBSC02(CR) Wedge Send Control Characters = 02 WDI4600...
Keyboard Settings Enter/Exit Programming Mode Wedge Quiet Interval Specifies amount of time to look for keyboard activity before scanner breaks keyboard connection in order to transmit data to host. The selectable range for this setting is 00 to 990 milliseconds (00-0x63 by 01) in increments of ten milliseconds. See page 214 in “References”...
Caps Lock State = Caps Lock ON $CKBCL02(CR) Caps Lock State = AUTO Caps Lock Enable Numlock This option specifies the setting of the NUMLOCK key in the Keyboard Wedge interface. $CKBNL00(CR) DEFAULT Numlock = NUMLOCK key unchanged $CKBNL01(CR) Numlock = Numlock key toggled WDI4600...
Keyboard Settings Enter/Exit Programming Mode USB Keyboard Speed This option specifies the USB poll rate for a USB keyboard. This feature applies ONLY to the USB Keyboard interface. $CKBSP01(CR) DEFAULT USB Keyboard Speed = 1ms $CKBSP02(CR) USB Keyboard Speed = 2ms $CKBSP03(CR) USB Keyboard Speed = 3ms $CKBSP04(CR)
$CKBSP09(CR) USB Keyboard Speed = 9ms $CKBSP0A(CR) USB Keyboard Speed = 10ms USB Keyboard Numeric Keypad This option Controls whether numeric characters will be sent using standard keys or the numeric keypad. $CKBKP00(CR) DEFAULT Standard Keys $CKBKP01(CR) Numeric Keypad WDI4600...
USB-OEM INTERFACE USB-OEM D EVICE SAGE on page 42 NTERFACE PTIONS on page 42 Feature settings for USB interfaces differ depending upon which host type the reader will be connected with. Use the feature settings in this chapter to specifically configure for the USB- OEM interface.
DATA FORMAT LOBAL REFIX UFFIX starting on page 44 AIM ID LOBAL starting on page 45 ABEL starting on page 48 • Label ID: Pre-Loaded Sets • Individually Set Label ID • Label ID Control • Label ID Symbology Selection • 1D Symbologies •...
Set Global Prefix $CLFSU Set Global Suffix Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the begin- ning. CANCEL No Global Prefix DEFAULT Global Suffix = 0x0D (CR) WDI4600...
Data Format Enter/Exit Programming Mode Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. See Table 2 on page 3-45 for a listing of AIM IDs.
Page 56
PLESSEY POSTAL AUSTRALIAN POSTAL IMB POSTAL JAPANESE POSTAL KIX POSTAL PLANET POSTAL PORTUGAL POSTAL POSTNET BB POSTAL ROYAL MAIL POSTAL SWEDISH POSTNET QR CODE TRIOPTIC UPCA UPCA P2 UPCA P5 UPCA COMPOSITE UPCE UPCE P2 UPCE P5 UPCE COMPOSITE WDI4600...
Data Format Enter/Exit Programming Mode Set AIM ID Individually for GS1-128 This feature configures a Label ID individually for the GS1-128 symbology and the programming for this works the same way as Label ID. See Label ID: Set Individually Per Symbology, starting on page 224 for detailed instructions on setting this feature.
Any custom config- uration or custom defaults will be lost. CAUTION $AE(CR) Label ID Pre-loaded Set = USA Set $Ae(CR) DEFAULT Label ID Pre-loaded Set = EU Set WDI4600...
Data Format Enter/Exit Programming Mode Individually Set Label ID This feature configures a Label ID individually for a single symbology. To set, first define whether you want it as a prefix or suffix by scanning a label below. Then turn to Label ID Symbology Selection •...
Set EAN 13 Label ID Character(s) Set Code 11 Label ID Character(s) $C3MID $CC8ID Set EAN 13 Composite Label ID Character(s) Set Code 128 Label ID Character(s) $C32ID $CC3ID Set EAN 13 P2 Label ID Character(s) Set Code 39 Label ID Character(s) WDI4600...
Page 61
Data Format Enter/Exit Programming Mode Label ID Symbology Selection − 1D Symbologies (continued) $CCCID $C35ID Set EAN 13 P5 Label ID Character(s) Set Code 39 CIP Label ID Character(s) $CXCID $C8BID Set EAN 8 Label ID Character(s) Set GS1 DataBar Expanded Composite Label ID Character(s) $C8MID $CU8ID...
Page 62
Set ISBN Label ID Character(s) Set Portugal Postal Code Label ID Character(s) $CINID $CPNID Set ISSN Label ID Character(s) Set Postnet Label ID Character(s) $CPKID $CPJID Set Japan Postal Code Label ID Character(s) Set Kix Postal Code Label ID Character(s) WDI4600...
Page 63
Data Format Enter/Exit Programming Mode Label ID Symbology Selection − 1D Symbologies (continued) $CPBID $CPZID Set PZN Code Label ID Character(s) Set Postnet BB Label ID Character(s) $CPRID $CAMID Set Royal Postal Code Label ID Character(s) Set UPC-A Composite Label ID Character(s) $CS2ID $CA2ID Set Standard 2 of 5 Label ID Character(s)
Page 64
Set China Sensible Label ID Character(s) Set PDF 417 Label ID Character(s) $CDMID $CMIID Set Data Matrix Label ID Character(s) Set Micro PDF 417 Label ID Character(s) $CMQID $CQRID Set Micro QR Label ID Character(s) Set QR Code Label ID Character(s) WDI4600...
Data Format Enter/Exit Programming Mode Advanced Formatting: User Label Edit Advanced formatting is available to create user label edit scripts. Contact Wasp Technical Support for information. Case Conversion This feature allows conversion of the case of all alphabetic characters to upper or lower case.
FF, then no conversion is done. If less than the expected string of 16 characters are selected, scan the ENTER/ EXIT barcode twice to accept the selections and exit Programming Mode. $CLFCH Configure Character Conversion 0xFFFFFFFFFFFFFFFF DEFAULT (No character conversion) WDI4600...
READING PARAMETERS OUBLE IMEOUT starting on page 58 EEPER NDICATORS starting on page 60 • Power On Alert • Good Read: When to Indicate • Good Read Beep Type • Good Read Beep Frequency • Good Read Beep Length • Good Read Beep Volume •...
This feature specifies when the reader will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. $CBPIN00(CR) DEFAULT Indicate Good Read = After Decode $CBPIN01(CR) Indicate Good Read = After Transmit $CBPIN02(CR) Indicate Good Read = After CTS goes inactive then active WDI4600...
Reading Parameters Enter/Exit Programming Mode Good Read Beep Type Specifies whether the good read beep has a mono or bitonal beep sound. $CBPTY00(CR) DEFAULT Good Read Beep Type = Mono $CBPTY01(CR) Good Read Beep Type = Bitonal Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below.
Reading Parameters Enter/Exit Programming Mode Good Read Beep Volume Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume levels. $CBPVO00CR) Good Read Beep Volume = Beeper Off $CBPVO01CR) Good Read Beep Volume = Low $CBPVO02CR) Good Read Beep Volume = Medium $CBPVO03CR)
Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 003 = Good Read LED DEFAULT stays on for 300 ms. Indicators are dimmed during sleep. WDI4600...
Stand Mode scanning is active. If reader detects motion and switches out of Stand Mode into Triggered Mode, blinking will stop until Stand Mode is active again. $CSMFL00(CR) DEFAULT Stand Mode Indication = Disable $CSMFL01(CR) Stand Mode Indication = Enable WDI4600...
Reading Parameters Enter/Exit Programming Mode Stand Operation Specifies the behavior of the reader when stationary in a stand. When configured for Stand Mode, the reader will switch to Stand Mode when stationary. Below are further options concerning Stand Operation. Ignore Autorecognition. Disables mode switching when the reader is placed in a stand.
Pick Mode = Enable Stand Mode Sensitivity Sets the sensitivity level for stand mode wakeup. Choices are low, medium and high. $CSMSE00(CR) Stand Mode Sensitivity = Low $CSMSE01(CR) DEFAULT Stand Mode Sensitivity = Medium $CSMSE02(CR) Stand Mode Sensitivity = High WDI4600...
Reading Parameters Enter/Exit Programming Mode Stand Mode Illumination Off Time Specifies the amount of time reader illumination stays off after pulling the trigger when in Stand Mode. The configurable range is 01 to 32 by 01 in increments of 500ms (500ms to 16 seconds). page 229 in “References”...
Select Motion Still Timeout Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 14 = Motion Still Timeout for 2 seconds DEFAULT WDI4600...
Reading Parameters Enter/Exit Programming Mode Flash On Time This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. See page 232 in “References”...
End by scanning the ENTER/EXIT barcode. Set Aiming Duration Timer Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL WDI4600...
Reading Parameters Enter/Exit Programming Mode Green Spot Duration Specifies the duration of the good read pointer beam after a good read. $CLSSP00(CR) Green Spot Duration = Disable (Green Spot is Off ) $CLSSP01(CR) DEFAULT Green Spot Duration = Short (300 msec) $CLSSP02(CR) Green Spot Duration = Medium (500 msec) $CLSSP03(CR)
ENTER/EXIT barcode prior to scanning a Decode Negative Image barcode. When this feature is enabled, you will be unable to read other programming labels in this manual. CAUTION $P,CIPVR00,P(CR) DEFAULT Decode Negative Image = Disable $P,CIPVR01,P(CR) Decode Negative Image = Enable WDI4600...
Reading Parameters Enter/Exit Programming Mode CORDED ONLY FEATURES Corded Stand Mode Sets the Stand Mode Operation for Corded models This feature is available starting with firmware release 610001013. $CSMVS00(CR) DEFAULT Corded Stand Mode = Disable $CSMVS01(CR) Corded Stand Mode = Generic Stand $CSMVS02(CR) Corded Stand Mode = for All-in-one and Base $CSMVS03(CR)
Enter/Exit Programming Mode Reading Parameters Corded Stand Beep Enables/Disables the beep that indicates when Corded Stand position is detected. This feature is available starting on firmware release 610001013. $CBPVS00(CR) DEFAULT Corded Stand Beep = Disable $CBPVS01(CR) Corded Stand Beep = Enable WDI4600...
Reading Parameters Enter/Exit Programming Mode MULTIPLE LABEL READING In standard (default) mode, when the reader’s aiming system is activated (by a trigger pull, motion or other method depending on the mode), it then acquires and processes each image in the area in front of it (the Volume). In this case, the scanner stops processing the image once it decodes a label.
000000000000 = Random order DEFAULT Multiple Labels Ordering by Code Length Specifies the transmission ordering by code length, when Multiple Labels per Frame is enabled. $CSNMT00(CR) DEFAULT Multiple Labels Ordering = Disable $CSNMT01(CR) $CSNMT02(CR) Transmit Increasing Length Order Transmit Decreasing Length Order WDI4600...
1D SYMBOLOGIES 1D Code Selection The reader supports the following 1D symbologies (barcode types). See "2D Symbologies" starting on page 171 for 2D barcodes. Symbology-dependent options are included in each chapter. • Disable All Symbologies, page 80 • GS1-128, page 118 •...
1. Scan the ENTER/EXIT PROGRAMMING Mode barcode. 2. Scan the Disable All Symbologies barcode. 3. Complete the programming sequence by scanning the ENTER/EXIT PROGRAM- MING barcode. $AD(CR) Disable All Symbologies This does not disable the reading of programming labels. WDI4600...
Code EAN/UPC Enter/Exit Programming Mode CODE EAN/UPC Coupon Control This feature is used to control the reader’s method of processing coupon labels. $CCPLC00(CR) Coupon Control = Allow all coupon barcodes to be decoded $CCPLC01(CR) DEFAULT Coupon Control = Enable only UPCA coupon decoding $CCPLC02(CR) Coupon Control = Enable only GS1 DataBar™...
UPC-A = Disable $CABEN01(CR) DEFAULT UPC-A = Enable UPC-A Check Character Transmission Enable this option to transmit the check character along with UPC-A barcode data. $CABCT00(CR) UPC-A Check Character Transmission = Don’t Send $CABCT01(CR) DEFAULT UPC-A Check Character Transmission = Send WDI4600...
Code EAN/UPC Enter/Exit Programming Mode Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. $CAB3B00(CR) DEFAULT UPC-A to EAN-13 = Don’t Expand $CAB3B01(CR) UPC-A to EAN-13 = Expand UPC-A Number System Character Transmission This feature enables/disables transmission of the UPC-A number system character.
$CAB2D01(CR) EAN-13 2D Component = 2D component must be decoded UPC-E The following options apply to the UPC-E symbology. UPC-E Enable/Disable When disabled, the reader will not read UPC-E barcodes. $CEBEN00(CR) UPC-E = Disable $CEBEN01(CR) DEFAULT UPC-E = Enable WDI4600...
UPC-E Enter/Exit Programming Mode UPC-E Check Character Transmission Enable this option to transmit the check character along with UPC-E barcode data. $CEBCT00(CR) UPC-E Check Character Transmission = Don’t Send $CEBCT01(CR) DEFAULT UPC-E Check Character Transmission = Send UPC-E 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded.
DEFAULT UPC-E to EAN-13 = Don’t Expand $CEB3B01(CR) UPC-E to EAN-13 = Expand Expand UPC-E to UPC-A Expands UPC-E data to the UPC-A data format. $CEBAB00(CR) DEFAULT UPC-E to UPC-A = Don’t Expand $CEBAB01(CR) UPC-E to UPC-A = Expand WDI4600...
GTIN Formatting Enter/Exit Programming Mode UPC-E Number System Character Transmission This feature enables/disables transmission of the UPC-E system number character. $CEBNS00(CR) UPC-E Number System Character = Do not transmit $CEBNS01(CR) DEFAULT UPC-E Number System Character = Transmit GTIN FORMATTING This feature enables/disables the ability to convert UPC-E, UPC-A, EAN 8, and EAN 13 labels into the GTIN 14-character format.
EAN 13 = Enable EAN 13 Check Character Transmission Enable this option to transmit the check character along with EAN 13 barcode data. $C3BCT00(CR) EAN 13 Check Character Transmission = Don’t Send $C3BCT01(CR) DEFAULT EAN 13 Check Character Transmission = Send WDI4600...
EAN 13 (Jan 13) Enter/Exit Programming Mode EAN-13 Flag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the first character of the label. $C3BF100(CR) EAN-13 Flag 1 Char= Don’t transmit $C3BF101(CR) DEFAULT EAN-13 Flag 1 Char= Transmit EAN-13 ISBN Conversion This option enables/disables conversion of EAN 13/JAN 13 Bookland labels starting with 978 to ISBN labels.
EAN-13 2D Component = 2D component must be decoded ISSN The following options apply to the ISSN symbology. ISSN Enable/Disable Enables/disables conversion of EAN/JAN13 Bookland labels starting with 977 to ISSN labels. $C3BIN00(CR) DEFAULT ISSN = Disable $C3BIN01(CR) ISSN = Enable WDI4600...
This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded. $C8B2D00(CR) DEFAULT EAN 8 2D Component = Disable (2D component not required) $C8B2D01(CR) EAN 8 2D Component = 2D component must be decoded WDI4600...
UPC/EAN Global Settings Enter/Exit Programming Mode UPC/EAN GLOBAL SETTINGS This section provides configuration settings for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for each feature description. UPC/EAN Price Weight Check This feature enables/disables calculation and verification of price/weight check digits. $CPWEN00(CR) DEFAULT Price Weight Check = Disabled...
10 times the width of the narrowest bar or space in the label. The property applies to all EAN-UPC symbologies globally and to the ADDONs. $CUNLO02(CR) DEFAULT UPC/EAN Quiet Zones = Two Modules $CUNLO03(CR) UPC/EAN Quiet Zones = Three Modules WDI4600...
Add-Ons Enter/Exit Programming Mode ADD-ONS Contact Customer Support for advanced programming of optional and conditional add-ons. Optional Add-ons The reader can be enabled to optionally read the following add-ons (supplementals): If a UPC/EAN base label and an add-on are both decoded, the reader will transmit the base label and add-on.
Add-Ons Enter/Exit Programming Mode Optional GS1-128 Add-On Timer This option sets the timer expiration value to read the added part after reading the linear EAN/ UPC part. For UPC/EAN add-ons other than those of that type, see "Optional Add-On Timer" on page 96. $CADUT00(CR) DEFAULT Optional GS1-128 Add-On Timer = Disable...
When disabled, any check character in the label is treated as a data character $CC3CC00(CR) Code 39 Check Character Calculation = Don’t Calculate $CC3CC01(CR) DEFAULT Code 39 Check Character Calculation = Calculate Std Check $CC3CC02(CR) Code 39 Check Character Calculation = Calculate Mod 7 Check WDI4600...
Code 39 Enter/Exit Programming Mode Code 39 Check Character Calculation (continued) $CC3CC04(CR) Code 39 Check Character Calculation = Enable Italian Post Check $CC3CC08(CR) Code 39 Check Character Calculation = Enable Daimler Chrysler Check Code 39 Check Character Transmission Enable this option to transmit the check character along with Code 39 barcode data. $CC3CT00(CR) Code 39 Check Character Transmission = Don’t Send $CC3CT01(CR)
Code 39 Enter/Exit Programming Mode Code 39 Quiet Zones This feature specifies the number of quiet zones for Code 39 labels. Quiet zones are blank areas at the ends of a barcode, typically 10 times the width of the narrowest bar or space in the label. $CC3LO02(CR) Code 39 Quiet Zones = Quiet Zones on two sides $CC3LO03(CR)
Select Code 39 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 02 = Length 1 is 2 Characters DEFAULT WDI4600...
Code 39 Enter/Exit Programming Mode Code 39 Set Length 2 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
Code 32 (Ital Pharmaceutical Code) Enter/Exit Programming Mode Code 32 Feature Setting Exceptions The following features are set for Code 32 by using these Code 39 settings: "Code 39 Quiet Zones" on page 105 "Code 39 Length Control" on page 105 "Trioptic Code"...
Code 128 Enter/Exit Programming Mode Code 128 Check Character Transmission Enable this option to transmit the check character along with Code 128 barcode data. $CC8CT00(CR) DEFAULT Code 128 Check Character Transmission = Don’t Send $CC8CT01(CR) Code 128 Check Character Transmission = Send Code 128 Function Character Transmission Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
10 times the width of the narrowest bar or space in the label. $CC8LO02(CR) Code 128 Quiet Zones = Quiet Zones on two sides $CC8LO03(CR) DEFAULT Code 128 Quiet Zones = Small Quiet Zones on two sides WDI4600...
Code 128 Enter/Exit Programming Mode Code 128 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 128 symbology. See page 217 for more information. $CC8LC00(CR) DEFAULT Code 128 Length Control = Variable Length $CC8LC01(CR) Code 128 Length Control = Fixed Length Product Reference Guide...
Select Code 128 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 01 = Length 1 is 1 Character DEFAULT WDI4600...
Code 128 Enter/Exit Programming Mode Code 128 Set Length 2 This feature specifies one of the barcode lengths for Code 128 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
GS1-128 = Do not transmit GS1-128 labels GS1-128 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CU82D00(CR) DEFAULT GS1-128 2D Component = Disable $CU82D01(CR) GS1-128 2D Component = Enable WDI4600...
Code ISBT 128 Enter/Exit Programming Mode CODE ISBT 128 The following options apply to the ISBT 128 symbology. ISBT 128 Concatenation Use this option to enable/disable ISBT128 concatenation of 2 labels. $CI8CE00(CR) DEFAULT ISBN 128 Concatenation = Disable $CI8CE01(CR) ISBN 128 Concatenation = Enable ISBT 128 Force Concatenation When enabled, this feature forces concatenation for ISBT.
Specifies the concatenation mode between Static and Dynamic. ISBT 128 Concate- This option is only valid when ISBT 128 Concatenation is enabled (see " nation" on page 119 $CI8CM00CR) DEFAULT ISBT 128 Concatenation Mode = Static $CI8CM01CR) ISBT 128 Concatenation Mode = Dynamic WDI4600...
The following options apply to the I 2 of 5 symbology. I 2 of 5 Enable/Disable When disabled, the reader will not read I 2 of 5 barcodes. $CI2EN00(CR) DEFAULT I 2 of 5 = Disable $CI2EN01(CR) I 2 of 5 = Enable WDI4600...
Interleaved 2 of 5 (I 2 of 5) Enter/Exit Programming Mode I 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional I 2 of 5 check character. $CI2CC00(CR) DEFAULT I 2 of 5 Check Character Calculation = Disable $CI2CC01(CR) I 2 of 5 Check Character Calculation = Check Standard (Modulo 10)
For variable length decoding, a minimum and maximum length may be set. Variable Length: Fixed Length: For fixed length decoding, two different lengths may be set. $CI2LC00(CR) DEFAULT I 2 of 5 Length Control = Variable Length $CI2LC01(CR) I 2 of 5 Length Control = Fixed Length WDI4600...
Interleaved 2 of 5 (I 2 of 5) Enter/Exit Programming Mode I 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode.
Select I 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 50 = Length 2 is 50 Characters DEFAULT WDI4600...
Interleaved 2 of 5 CIP HR Enter/Exit Programming Mode INTERLEAVED 2 OF 5 CIP HR The following options apply to the Interleaved 2 of 5 CIP HR symbology. Interleaved 2 of 5 CIP HR Enable/Disable Enables/Disables ability of reader to decode Interleaved 2 of 5 CIP HR labels. $CCHEN00(CR) DEFAULT Interleaved 2 of 5 CIP HR = Disable...
Standard 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional Standard 2 of 5 check character. $CS2CC00(CR) DEFAULT Standard 2 of 5 Check Character Calculation = Disable $CS2CC01(CR) Standard 2 of 5 Check Character Calculation = Enable WDI4600...
Standard 2 of 5 Enter/Exit Programming Mode Standard 2 of 5 Check Character Transmission This feature enables/disables transmission of an optional Standard 2 of 5 check character. $CS2CT00(CR) Standard 2 of 5 Check Character Transmission = Don’t Send $CS2CT01(CR) DEFAULT Standard 2 of 5 Check Character Transmission = Send Standard 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Standard 2...
Select Standard 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 08 = Length 1 is 8 Characters DEFAULT WDI4600...
Standard 2 of 5 Enter/Exit Programming Mode Standard 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length...
Industrial 2 of 5 Check Character Calculation Enables/Disables calculation and verification of an optional Industrial 2 of 5 check character. $CU2CC00(CR) DEFAULT Industrial 2 of 5 Check Character Calculation = Disable $CU2CC01(CR) Industrial 2 of 5 Check Character Calculation = Enable WDI4600...
Industrial 2 of 5 Enter/Exit Programming Mode Industrial 2 of 5 Check Character Transmission Enables/disables transmission of an Industrial 2 of 5 check character. $CU2CT00(CR) Industrial 2 of 5 Check Character Transmission = Disable $CU2CT01(CR) DEFAULT Industrial 2 of 5 Check Character Transmission = Enable Industrial 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Industrial 2 of 5 symbology.
Select Industrial 2 of 5 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 01 = Length 1 is 1 Character DEFAULT WDI4600...
Industrial 2 of 5 Enter/Exit Programming Mode Industrial 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Industrial 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length...
Codabar Enter/Exit Programming Mode CODABAR The following options apply to the Codabar symbology. Codabar Enable/Disable When disabled, the reader will not read Codabar barcodes. $CCBEN00(CR) DEFAULT Codabar = Disable $CCBEN01(CR) Codabar = Enable Codabar Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Codabar check character.
DEFAULT Codabar Check Character Transmission = Send Codabar Start/Stop Character Transmission Enable this option to enable/disable transmission of Codabar start and stop characters $CCBSS00(CR) Codabar Start/Stop Character Transmission = Don’t Transmit $CCBSS01(CR) DEFAULT Codabar Start/Stop Character Transmission = Transmit WDI4600...
Codabar Enter/Exit Programming Mode Codabar Start/Stop Character Set This option specifies the format of transmitted Codabar start/stop characters $CCBSC00(CR) Codabar Check Character Set = ABCD/TN*E $CCBSC01(CR) Codabar Check Character Set = ABCD/ABCD $CCBSC02(CR) Codabar Check Character Set = abcd/tn*e $CCBSC03(CR) DEFAULT Codabar Check Character Set = abcd/abcd Codabar Start/Stop Character Match...
For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. $CCBLC00(CR) DEFAULT Codabar Length Control = Variable Length $CCBLC01(CR) Codabar Length Control = Fixed Length WDI4600...
Codabar Enter/Exit Programming Mode Codabar Set Length 1 This feature specifies one of the barcode lengths for Codabar Length ControlCodabar Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode.
Scan ENTER/EXIT PROGRAMMING MODE $CCBL2 Select Codabar Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 50 = Length 2 is 50 Characters DEFAULT WDI4600...
ABC Codabar Enter/Exit Programming Mode ABC Codabar Force Concatenation Forces labels starting or ending with D to be concatenated. $CCBFC00(CR) DEFAULT ABC Codabar Force Concatenation = Disable $CCBFC01(CR) ABC Codabar Force Concatenation = Enable Product Reference Guide...
This option enables/disables calculation and verification of optional Code 11 check character. $CC1CC00(CR) Code 11 Check Character Calculation = Disable $CC1CC01(CR) Code 11 Check Character Calculation = Check C $CC1CC02(CR) Code 11 Check Character Calculation = Check K $CC1CC03(CR) DEFAULT Code 11 Check Character Calculation = Check C and K WDI4600...
Code 11 Enter/Exit Programming Mode Code 11 Check Character Transmission This feature enables/disables transmission of an optional Code 11 check character. $CC1CT00(CR) Code 11 Check Character Transmission = Don’t Send $CC1CT01(CR) DEFAULT Code 11 Check Character Transmission = Send Code 11 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 11 symbology.
Select Code 11 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 04 = Length 1 is 4 Characters DEFAULT WDI4600...
Code 11 Enter/Exit Programming Mode Code 11 Set Length 2 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
GS1 DataBar™ Expanded Enter/Exit Programming Mode GS1 DataBar™ Omnidirectional 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label for this symbology is decoded. $C4B2D00(CR) DEFAULT GS1 DataBar™ Omnidirectional 2D Component = Disable (2D component not required) $C4B2D01(CR) GS1 DataBar™...
GS1 DataBar™ Expanded 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CXB2D00(CR) DEFAULT GS1 DataBar™ Expanded 2D Component = Disable $CXB2D01(CR) GS1 DataBar™ Expanded 2D Component = Enable WDI4600...
GS1 DataBar™ Expanded Enter/Exit Programming Mode GS1 DataBar™ Expanded Length Control This feature specifies either variable length decoding or fixed length decoding for the GS1 DataBar™ Expanded symbology. Variable Length: For variable-length decoding, a minimum length may be set. Fixed Length: For fixed-length decoding, two different lengths may be set.
Select GS1 DataBar™ Expanded Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 01 = Length 1 is 1 Character DEFAULT WDI4600...
GS1 DataBar™ Expanded Enter/Exit Programming Mode GS1 DataBar™ Expanded Set Length 2 This feature specifies one of the barcode lengths for GS1 DataBar™ Expanded Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if Fixed Length Mode.
Code 93 Enter/Exit Programming Mode GS1 DataBar™ Limited 2D Component This feature enables/disables a requirement that a 2D label component be decoded when a base label of this symbology is decoded. $CLB2D00(CR) DEFAULT GS1 DataBar™ Limited 2D Component = Disable (2D component not required) $CLB2D01(CR) GS1 DataBar™...
Code 93 Check Character Calculation = Enable Check C and K Code 93 Check Character Transmission Enables/disables transmission of an optional Code 93 check character. $CC9CT00(CR) Code 93 Check Character Transmission = Disable $CC9CT01(CR) DEFAULT Code 93 Check Character Transmission = Enable WDI4600...
Code 93 Enter/Exit Programming Mode Code 93 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 93 symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set.
Select Code 93 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 01 = Length 1 is 1 Character DEFAULT WDI4600...
Code 93 Enter/Exit Programming Mode Code 93 Set Length 2 This feature specifies one of the barcode lengths for Code 93 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
DEFAULT Code 93 Quiet Zones = Small Quiet Zones on two sides The following options apply to the MSI symbology. MSI Enable/Disable Enables/Disables ability of reader to decode MSI labels. $CMSEN00(CR) DEFAULT MSI = Disable $CMSEN01(CR) MSI = Enable WDI4600...
For variable length decoding, a minimum and maximum length may be Variable Length: set. For fixed length decoding, two different lengths may be set. Fixed Length: $CMSLC00(CR) DEFAULT MSI Length Control = Variable Length $CMSLC01(CR) MSI = Fixed Length WDI4600...
Enter/Exit Programming Mode MSI Set Length 1 This feature specifies one of the barcode lengths for . Length 1 is the MSI Length Control minimum label length if in Mode, or the first fixed length if in Variable Length Fixed Mode.
Scan ENTER/EXIT PROGRAMMING MODE $CMSL2 Select MSI Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 50 = Length 2 is 50 Characters DEFAULT WDI4600...
Plessey Enter/Exit Programming Mode PLESSEY The following options apply to the Plessey symbology. Plessey Enable/Disable Enables/Disables ability of reader to decode Plessey labels. $CPLEN00CR) DEFAULT Plessey = Disable $CPLEN01CR) Plessey = Enable Plessey Check Character Calculation Enables/Disables calculation and verification of an optional Plessey check character. $CPLCC00(CR) Plessey Check Character Calculation = Disable $CPLCC01(CR)
Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. $CPLLC00(CR) DEFAULT Plessey Length Control = Variable Length $CPLLC01(CR) Plessey = Fixed Length WDI4600...
Plessey Enter/Exit Programming Mode Plessey Set Length 1 This feature specifies one of the barcode lengths for Plessey Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode.
Scan ENTER/EXIT PROGRAMMING MODE $CPLL2 Select Plessey Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 50 = Length 2 is 50 Characters DEFAULT WDI4600...
2D SYMBOLOGIES 2D Global Features • 2D Maximum Decoding Time, page • 2D Normal/Inverse Symbol Control, page 173 • 2D Structured Append, page 173 The reader supports the following 2D symbologies (barcode types). Symbology-dependent options for each symbology are included in this chapter. See "1D Code Selection"...
2D Maximum Decoding Time = 350 msec $CDETM80(CR) 2D Maximum Decoding Time = 500 msec $CDETM16(CR) 2D Maximum Decoding Time = 1 Second $CDETMC8(CR) 2D Maximum Decoding Time = 2 Seconds $CDETMFF(CR) 2D Maximum Decoding Time = 2.55 Seconds WDI4600...
2D Global Features Enter/Exit Programming Mode 2D Structured Append Enables/disables ability of reader to append multiple 2D Codes labels in a structured format. The structured append property is globally applied to the following symbologies, if these are enabled: • Data Matrix •...
For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. $CAZLC00(CR) DEFAULT Aztec Code Length Control = Variable Length $CAZLC01(CR) Aztec Code Length Control = Fixed Length WDI4600...
Aztec Code Enter/Exit Programming Mode Aztec Code Set Length 1 Specifies one of the barcode lengths for Aztec Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 3,832 characters in increments of 0001 (pad with zeroes).
End by scanning the ENTER/EXIT Select Aztec Code Length 2 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL Length 2 is 3,832 Characters DEFAULT WDI4600...
China Sensible Code Enter/Exit Programming Mode China Sensible Code China Sensible Code Enable / Disable Enables/disables the ability of the reader to decode China Sensible Code labels. $CCSEN00(CR) DEFAULT China Sensible Code = Disable $CCSEN01(CR) China Sensible Code = Enable China Sensible Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology.
Select China Sensible Code Length 1 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 0001 = Length 1 is 1 Character DEFAULT WDI4600...
China Sensible Code Enter/Exit Programming Mode China Sensible Code Set Length 2 This feature specifies one of the barcode lengths for China Sensible Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
The configuration item can also be configured as a bit mask to filter one or more Data Matrix labels with different symbol size AND shape styles. $CDMDM3FFF0BDF) Data Matrix Dimensions Mask = Square Style $CDMDM0000420 Data Matrix Dimensions Mask = Rectangular Style $CDMD03FFFFFF DEFAULT Data Matrix Dimensions Mask = Both Square and Rectangular Style WDI4600...
Data Matrix Enter/Exit Programming Mode Data Matrix Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. $CDMLC00(CR) DEFAULT Data Matrix Length Control = Variable Length...
End by scanning the ENTER/EXIT Select Data Matrix Length 2 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL Length 2 is 3,116 Characters DEFAULT WDI4600...
Maxicode Enter/Exit Programming Mode Maxicode Maxicode Enable / Disable Enables/disables ability of reader to decode Maxicode labels. $CMXEN00(CR) DEFAULT Maxicode = Disable $CMXEN01(CR) Maxicode = Enable Maxicode Primary Message Transmission Enables/disables the transmission of only the Primary Message when the Secondary Message is not readable.
Select Maxicode Length 1 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 0001 = Length 1 is 1 Character DEFAULT WDI4600...
Maxicode Enter/Exit Programming Mode Maxicode Set Length 2 This feature specifies one of the barcode lengths for Maxicode Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. $CP4LC00(CR) DEFAULT PDF417 Length Control = Variable Length $CP4LC01(CR) PDF417 Length Control = Fixed Length WDI4600...
PDF417 Enter/Exit Programming Mode PDF417 Set Length 1 Specifies one of the barcode lengths for PDF417 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only.
End by scanning the ENTER/EXIT Select PDF417 Length 2 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL Length 2 is 2,710 Characters DEFAULT WDI4600...
Select Micro PDF417 Length 1 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 0001 = Length 1 is 1 Character DEFAULT WDI4600...
Micro PDF417 Enter/Exit Programming Mode Micro PDF417 Set Length 2 This feature specifies one of the barcode lengths for Micro PDF417 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length includes the barcode’s data characters only.
For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. $CQRLC00(CR) DEFAULT QR Code Length Control = Variable Length $CQRLC01(CR) QR Code Length Control = Fixed Length WDI4600...
QR Code Enter/Exit Programming Mode QR Code Set Length 1 Specifies one of the barcode lengths for QR Code Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Characters can be set from 0001 to 7,089 characters in increments of 0001 (pad with zeroes).
End by scanning the ENTER/EXIT Select QR Code Length 2 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL Length 2 is 7,089 Characters DEFAULT WDI4600...
Micro QR Code Enter/Exit Programming Mode Micro QR Code Micro QR Code Enable/Disable Enables/disables the ability of the reader to decode Micro QR Code labels MQEN00 DEFAULT Micro QR Code = Disable MQEN01 Micro QR Code = Enable Micro QR Code Length Control This feature specifies either variable length decoding or fixed length decoding for this symbology.
Select Micro QR Code Length 1 Setting barcode again. Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 0001 = Length 1 is 1 Character DEFAULT WDI4600...
Micro QR Code Enter/Exit Programming Mode Micro QR Code Set Length 2 This feature specifies one of the barcode lengths for Micro QR Code Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode.
Enables/disables the ability of the reader to decode the stacked part of a UCC Composite label. Global This feature is not effective when Global AIM IDs are enabled (see " AIM ID" on page 45 $CCMEN00(CR) DEFAULT UCC Composite = Disable $CCMEN01(CR) UCC Composite = Enable WDI4600...
UCC Composite UCC Optional Composite Timer Specifies the amount of time the system will wait for the stacked part of a UCC Composite label before transmitting the linear label without an add-on. $CCMOT00(CR) DEFAULT UCC Optional Composite Timer = Timer Disabled $CCMOT01(CR) UCC Optional Composite Timer = 100msec $CCMOT02(CR)
Postal Code Selection = Disable All Postal Codes $CPOEN01(CR) Postal Code Selection = Enable Postnet $CPOEN02(CR) Postal Code Selection = Enable Planet $CPOEN03(CR) Postal Code Selection = Enable Royal Mail $CPOEN04(CR) Postal Code Selection = Enable Kix $CPOEN05(CR) Postal Code Selection = Enable Australia Post WDI4600...
Postal Code Selection Postal Code Selection (continued) $CPOEN06(CR) Postal Code Selection = Enable Japan Post $CPOEN07(CR) Postal Code Selection = Enable IMB $CPOEN08(CR) Postal Code Selection = Enable Sweden Post $CPOEN09(CR) Postal Code Selection = Enable Portugal Post Postnet BB Control Controls the ability of the scanner to decode B and B' fields of Postnet labels.
MOTION FEATURES OTION IMING ONTROL on page 203 OTION ENSITIVITY on page 204 OTIONLESS IMEOUT on page 204 Use this chapter to configure motion settings for the handheld. Reference Appendix B for a listing of standard factory settings. Motion Aiming Control Configures the ability of the scanner to Enable/Disable the Aiming system when motion is detected.
End by scanning the ENTER/EXIT barcode again. Select Motionless Timeout Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL 020 = Motionless Timeout = 2 seconds DEFAULT WDI4600...
Chapter 4 References This section contains explanations and examples of selected barcode features. See "Configuration Using Barcodes" starting on page 15 for the actual barcode labels used to configure the reader. RS-232 P ARAMETERS starting on page 206 • RS-232 •...
RTS/XON/XOFF — RTS is asserted during transmissions. CTS is ignored. XON and XOFF gate transmissions. • RTS On/CTS — RTS is always asserted. CTS gates transmissions. RTS/CTS Scan Control — RTS is asserted during transmissions. CTS gates transmissions and controls enable and disable state of scanner. WDI4600...
RS-232 Parameters RS-232/USB COM Parameters Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments.
Page 218
Hex equivalent from ASCII 0x06 0x24 0x40 0x3E Chart Scan ENTER/EXIT PROGRAMMING MODE Scan SELECT ACK CHARACTER SETTING Scan Two Characters from ‘0’ and ‘6’ ‘2’ and ‘4’ ‘4’ and ‘0’ ‘3’ AND ‘E’ Appendix D, Keypad Scan ENTER/EXIT PROGRAMMING MODE WDI4600...
Page 219
RS-232 Parameters NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected. Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters.
Page 220
15,000ms (15 sec.) Divide by 200 Scan ENTER/EXIT PROGRAMMING MODE Scan SELECT ACK NAK TIMEOUT VALUE SETTING Scan Two Characters From ‘0’ and ‘1’ ‘0’ and ‘5’ ‘2’ and ‘6’ ‘7’ and ‘5’ Appendix D, Keypad Scan ENTER/EXIT PROGRAMMING MODE WDI4600...
Page 221
RS-232 Parameters ACK NAK Retry Count This feature specifies the number of times the reader retries a label transmission due to a retry condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and a selection of 255 specifies unlimited retries.
Page 222
Hex equivalent from 0x64 0x7D 0x44 0xFF Chart Scan ENTER/EXIT PROGRAMMING MODE Scan SELECT DISABLE CHARACTER VALUE SETTING Scan Two Characters From ‘6’ and ‘4’ ‘7’ and ‘D’ ‘4’ and ‘4’ ‘F’ AND ‘F’ Appendix D, Keypad Scan ENTER/EXIT PROGRAMMING MODE WDI4600...
Page 223
RS-232 Parameters Enable Character Specifies the value of the RS-232 host command used to enable the reader. ASCII characters or any hex value from 0 to 0xFF can be selected. Setting to previously defined characters such as XON, XOFF, or host com- mands conflicts with normal operation of these characters.
Divide by 10 (and pad with leading zeroes) Scan ENTER/EXIT PROGRAMMING MODE Scan SELECT WEDGE QUIET INTERVAL SETTING Scan Two Characters From ‘0’ and ‘1’ ‘1’ and ‘5’ ‘6’ and ‘0’ ‘8’ and ‘5’ Appendix D, Keypad Scan ENTER/EXIT PROGRAMMING MODE WDI4600...
Keyboard Interface Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. This feature applies ONLY to the Keyboard Wedge interface.
60 Seconds 99 Seconds Pad with leading zero(es) Scan ENTER/EXIT PROGRAMMING MODE Scan SELECT INTERCODE DELAY SETTING Scan Two Characters From ‘0’ and ‘0’ ‘0’ and ‘5’ ‘6’ and ‘0’ ‘9’ AND ‘9’ Appendix D, Keypad Scan ENTER/EXIT PROGRAMMING MODE WDI4600...
Symbologies Symbologies Set Length Length Control allows you to select either variable length decoding or fixed length decoding for the specified symbology. Variable Length: For variable length decoding, a minimum and maximum length may be set. Fixed Length: For fixed length decoding, two different lengths may be set. Set Length 1 This feature specifies one of the barcode lengths for Length Control.
Label ID Suffix AIM ID: This function is used to identify and display the common label identifier for its symbology. When enabled, this ID code will be transmitted before the scanned bar code data. 00 - 20 Characters (ASCII) WDI4600...
Data Editing Please Keep In Mind... • Modifying a message string is not a mandatory requirement. Data editing is a sophisti- cated feature allowing highly customizable output for advanced users. Factory default set- tings for data editing is typically set to NONE. •...
Code 11 a. UPC-A and UPC-E labels are converted to EAN 13 when adding AIM IDs. b. ISBN (X with a 0 modifier character) Figure 8. AIM ID Prefix Label ID AIM ID Bar Code Data Label ID Suffix WDI4600...
Data Editing Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x01- 0xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled.
Page 233
Data Editing USA Label ID set EU Label ID set Symbology Default Default Default Default Character ASCII Character ASCII 400000 5A0000 PDF417 500000 720000 PLESSEY 610000 610000 POSTAL AUSTRALIAN 244B00 244B00 POSTAL IMB 245600 245600 POSTAL JAPANESE 245200 245200 POSTAL KIX 245500 245500 POSTAL PLANET...
Page 234
7. Scan the ENTER/EXIT barcode once again to exit Programming Mode. This completes the steps to configure a Label ID for a given symbology. Figure 9. Label ID Position Options Prefix Label ID Aim ID Bar Code Data Label ID Suffix WDI4600...
Page 235
Data Editing Table 36 . Label ID Examples STEP ACTION EXAMPLES Scan the ENTER/EXIT barcode (Scanner enters Programming Mode) Determine placement of the Label ID characters BEFORE or AFTER with regard to scanned Enable as Prefix Enable as Suffix Enable as Prefix Enable as Suffix data using "Label ID...
5. Scan the ENTER/EXIT barcode to exit Programming Mode. If less than the expected string of 16 characters are selected, scan the ENTER/ EXIT barcode twice to accept the selections and exit Programming Mode. WDI4600...
Reading Parameters Reading Parameters Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 10 milliseconds to 2,550 milliseconds (0.001 to 2.55 seconds) in 100ms increments.
No trigger pull is required to read a barcode. Scanning is turned on automatically when an item is placed in the reader’s field of view. If the trigger is pulled, the reader acts as if it in single read mode. Double Read Timeout prevents undesired multiple reads while in this mode. WDI4600...
Scanning Features Stand Mode Off Time This feature specifies the amount of time reader illumination stays off after pulling the trigger when in Stand Mode. The configurable range is 01 to 32 by 01 in increments of 500ms (500ms to 16 seconds). Follow these instructions to set this feature: 1.
Scanning Features Aiming Duration Time Specifies the frame of time the aiming pointer remains on after decoding a label, when in trigger single mode. The range for this setting is from 1 to 255 seconds in 1-second increments. Follow these instructions to set this feature: 1.
Scan ENTER/EXIT PROGRAMMING MODE Scan SELECT FLASH ON TIME SETTING Scan Two Characters From ‘0’ and ‘5’ ‘1’ and ‘0’ ‘5’ and ‘2’ ‘9’ and ‘9’ Appendix D, Keypad Scan ENTER/EXIT PROGRAMMING MODE WDI4600...
Scanning Features Flash Off Time This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1.
Scan SELECT SYMBOLOGIES FOR MULTIPLE LABELS ORDERING Scan Two Characters From ‘2’ and ‘4’ ‘0’ and ‘E’ ‘0’ and ‘C’ ‘4’ and ‘E’ Appendix D, Keypad RESULT 0x240E0C4E0000 Scan ENTER/EXIT PROGRAMMING MODE Table 44 on page 235 shows the hex value associated with each symbology. WDI4600...
Page 245
Scanning Features Table 44 . Symbology Hex Values Value Symbology ID Value Symbology ID Don't care GTIN5 UPC-A GTIN8 UPC-E S2OF5 EAN8 PDF417 EAN13 CODE11 UPC2 IATA UPC5 MICRO_PDF C128_ADDON GS1 DataBar_LIM_ID EAN128 GS1 DataBar_LIM_COMP C128_PROGRAMMING_LABEL GS1 DataBar_Omnidirectional_COMP CODE128 GS1 DataBar_EXP_COMP FNC3_C128_LABEL GENERIC_DATA DATA MATRIX...
Appendix A Technical Specifications Table contains Physical and Performance Characteristics, User Environment and Regulatory information. Table 46 . Technical Specifications Item Description Physical Characteristics Color Black/Yellow Height 7.1”/181 mm Dimensions Length 3.9”/100 mm Width 2.8”/71 mm Weight (without cable) Approximately 6.9 ounces /195.6 g Performance Characteristics Scanning Illumination LEDs...
Page 248
QR Code 15mil: 0.4” to 7.5” (1.0 - 19cm) Standard Range: 1D Minimum Resolution = 4 mil Minimum Element Width PDF-417 Minimum Resolution = 5 mil Data Matrix Minimum Resolution = 7 mil Print Contrast Minimum 25% minimum reflectance WDI4600...
Page 249
GS1 DataBar Limited; GS1 DataBar Expanded; GS1 DataBar Truncated; DATABAR Expanded Coupon. 2D / Stacked Codes The WDI4600 scanner is capable of decoding the Decode Capability following symbologies using multiple frames (i.e. Multi-Frame Decoding): PDF-417; QR Code; Aztec; Data Matrix; Inverse Data Matrix; Data Matrix is configurable for the following parameters:;...
Page 250
Technical Specifications Item Description User Environment WDI4600 Operating Temperature 32° to 131° F (0° to 55° C) Charging Temperature Storage Temperature -4° to 158° F (-20° to 70° C) Humidity Operating: 5% to 90% relative humidity, non-condensing Drop Specifications Scanner withstands 18 drops from 1.8 meters (5.9 feet) to concrete...
Technical Specifications Imager Labeling Sample labels are shown for illustrative purposes only. Please view the labels on your product for actual details, as they may vary from those depicted. Scanner Regulatory Label Product Reference Guide...
Technical Specifications LED and Beeper Indications The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The tables below list these indications. One exception to the behaviors listed in the tables is that the reader’s functions are programmable, and may or may not be turned on.
Selftest and has entered FRU (Field Replaceable Unit) isolation mode. If the reader is reset, the sequence will be repeated. The following table describes the LED flashes/beep codes associated with an error found. NUMBER OF LED ERROR CORRECTIVE ACTION FLASHES/BEEPS Configuration Interface PCB Contact Helpdesk for assis- Digital PCB tance Imager Accelerometer WDI4600...
Appendix B Standard Defaults The most common configuration settings are listed in the “Default” column of the table below. Page references are also provided for feature descriptions and programming barcodes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features.
Page 256
Individually Set Label ID Disable Case Conversion Disable Character Conversion No Char Conversion READING PARAMETERS Double Read Timeout 0.6 Second Power On Alert Power-up Beep Good Read: When to Indicate After Decode Good Read Beep Type Mono Good Read Beep Frequency High WDI4600...
Page 257
Standard Defaults Page Parameter Default Your Setting Number Good Read Beep Length 80 ms Good Read Beep Volume High Good Read LED Duration 300 ms Scanning Features Scan Mode Trigger Single Stand Mode Indication Disable Stand Operation Switch to Stand Mode Pick Mode Disable Stand Mode Sensitivity...
Page 258
EAN 13 (Jan 13) EAN 13 Enable/Disable Enable EAN 13 Check Character Transmission Send EAN-13 Flag 1 Character Transmit EAN-13 ISBN Conversion Disable 2D Component Not EAN-13 2D Component Required ISSN ISSN Enable/Disable Disable EAN 8 EAN 8 Enable/Disable Enable WDI4600...
Page 259
Standard Defaults Page Parameter Default Your Setting Number EAN 8 Check Character Transmission Send Expand EAN 8 to EAN 13 Disable 2D Component Not EAN 8 2D Component Required UPC/EAN Global Settings UPC/EAN Price Weight Check Disable UPC/EAN Quiet Zones Two Modules Add-Ons Optional Add-ons...
Page 260
I 2 of 5 Check Character Calculation Disable I 2 of 5 Check Character Transmission Send I 2 of 5 Length Control Variable I 2 of 5 Set Length 1 I 2 of 5 Set Length 2 Interleaved 2 of 5 CIP HR WDI4600...
Page 261
Standard Defaults Page Parameter Default Your Setting Number Interleaved 2 of 5 CIP HR Enable/Disable Disable Follett 2 of 5 Follett 2 of 5 Enable/Disable Disable Standard 2 of 5 Standard 2 of 5 Enable/Disable Disable Standard 2 of 5 Check Character Calculation Disable Standard 2 of 5 Check Character Transmission Send...
Page 263
Standard Defaults Page Parameter Default Your Setting Number 2D component not GS1 DataBar™ Limited 2D Component required Code 93 Code 93 Enable/Disable Disable Code 93 Check Character Calculation Enable Check C and K Code 93 Check Character Transmission Enable Code 93 Length Control Variable Code 93 Set Length 1 Code 93 Set Length 2...
Page 264
Micro PDF417 Length Control Variable Micro PDF417 Set Length 1 Micro PDF417 Set Length 2 0366 QR Code Enable / Disable Enable QR Code Length Control Variable QR Code Set Length 1 QR Code Set Length 2 7,089 WDI4600...
Page 265
Standard Defaults Page Parameter Default Your Setting Number Micro QR Code Enable/Disable Disable Micro QR Code Length Control Variable Micro QR Code Set Length 1 0001 Micro QR Code Set Length 2 0035 UCC Composite Enable / Disable Disable UCC Optional Composite Timer Timer Disabled Postal Code Selection Disable all Postal codes...
Appendix C Sample Barcodes The sample barcodes in this appendix are typical representations for their symbology types. 1D Barcodes UPC-A EAN-13 978033029095 Code 39 Code 128 Code 128 Interleaved 2 of 5 Product Reference Guide...
Appendix E Scancode Tables Control Character Emulation Control character emulation selects from different scancode tables as listed in this appendix. Each of the control character sets below are detailed by interface type in the tables. These apply to Wedge and USB Keyboard platforms. Control Character 00 : Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1.
ð ñ ò ó ô õ ö ÷ ø ù ú û ü ý þ ÿ Extended characters (sky blue) are sent through dedicated keys (when available in the selected country mode) or by using an Alt Mode sequence. WDI4600...
Page 275
Interface Type PC AT PS/2, USB-Keyboard or USB-Keyboard for APPLE (continued) Table 52. Scancode Set When Control Character is 02 Enter Ar↓ Ar↑ Al↓ Al ↑ Cl ↓ Cl ↑ Cr ↓ Cr ↑ S+ Tab Enter Pg Up Keypd Pg Dwn Home...
Page 277
Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode (continued) Table 54. Scancode Set When Control Character is 02 Enter Ar↓ Ar↑ Al↓ Al ↑ Cl ↓ Cl ↑ Cr ↓ Cr ↑ S+ Tab Enter Pg Up ...
Sh↓ Sh↑ (keyp) Cl ↓ Cl ↑ Table 56. Scancode Set When Control Character is 02 Enter Cl ↓ Cl ↑ à S+ Tab Enter Keypd Space “ & ‘ < > WDI4600...
Table 60. Scancode Set when Control Character 02 Enter Ar↓ Ar↑ Al↓ Al ↑ Cl ↓ Cl ↑ Cr ↓ Cr ↑ S+ Tab Enter Pg Up Keypd Pg Dwn Home Space “ & ‘ < > ‘ WDI4600...
Scancode Tables Microsoft Windows Codepage 1252 Windows-1252 is a character encoding of the Latin alphabet, used by default in the legacy components of Microsoft Windows in English and some other Western languages. Product Reference Guide...