Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision User’s Manual of 4-channel Video over Fiber Bundle Kit (VF-402-T + VF-402-R) Model: VF-402-KIT Rev: 2 (May, 2017)
1.1 Package Contents Check the contents of your package for the following parts: z VF-402-T – Video over Fiber Media Converter (Transmitter) x 1 z VF-402-R – Video over Fiber Media Converter (Receiver) x 1 z 5V / 2A Power Adapter x 2 z User’s Manual x 1...
Page 6
Fiber Optic Communication for Video and Serial Data The VF-402-KIT consists of a Video Transmitter and a Video Receiver: z VF-402-T: 4-channel Video over Fiber Transmitter z VF-402-R: 4-channel Video over Fiber Receiver The VF-402-KIT is a digital fiber-optic transmission system that brings users a cost-effective solution for transmission of 4-channel uncompressed digital video and one reverse RS485 async data over one single fiber cable.
Page 7
Thus, it can observe working condition visually with LED. It can be a standalone or rack-mounted structure, and is simple to operate with no field adjustment needed. V id VF-402-T Transmitter Up to 20km V G A VF-402-R...
Analog Camera Long Distance IR Speed Dome Video Video Video Analog Camera Analog Camera Analog Camera Analog Camera Video Video Video Video Video VF-402-T VF-402-T RS-485 Transmitter Transmitter RS-485 RS-485 RS-485 VF-402-R Receiver VF-402-T Transmitter Video Analog Camera Video Video...
Typical Applications z Intelligent Transportation Systems (ITS) z Toll Collection z Traffic Surveillance z Air Traffic Management (ATM) z Rail Signaling z Perimeter Alarms and Area Monitoring z Telemedicine and Teleconference z Industrial Surveillance z Intelligent Building z CCTV Network 1.4 Product Features z Compliant with hybrid video (AHD/TVI/CVI/CVBS) z 20km long-distance data transmission...
1.5 Product Specifications Model VF-402-T VF-402-R Video Characteristics Video Channel 4-channel bi-direction Video Connector 1080p: AHD/TVI/CVI Supported Video Type 480p: CVBS Video Input/Output Impedance 75ohm/unbalanced interface Video Input/Output Voltage 1.0 Vpp / typical peak to peak value Video Bandwidth 25 to 60MHz...
Page 11
Temperature: -20 ~ 70 degrees C Operating Relative Humidity: 0 ~ 95% (non-condensing) Temperature: -40 ~ 85 degrees C Storage Relative Humidity: 0 ~ 95% (non-condensing) Standard Accessories VF-402-T x 1 VF-402-R x 1 Packet Contents User’s Manual x 1 5V/2A power adapter x 2...
Chapter 2. Hardware Description 2.1 Panel Overview Front Panel: Video interface Item Description VIDEO/V1…V4 Video input interface LED definition PWR: Power indicators -- when powered on, PWR LED is on. LNK: Optical link indicator -- after connecting the fiber connector, the indicator will show green when optical signal is detected.
Page 14
Rear Panel: There is a power interface on the rear panel; the description of each is as follows: 5V DC Power Supply Power supply Output 5V DC, 2A 1. The device is a power-required device, meaning it will not work till it is powered.
This section describes how to install your VF-402-KIT Video over fiber and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET VF- 402-KIT Video over fiber Converter does not need software configuration. To install your VF-402-KIT on a desktop or shelf, check the following sections.
(2) VF-402-T (Transmitter): Connect coaxial cable from analog camera to video BNC port of the VF-402-T. (3) Attach FC single mode fiber cable from the VF-402-T to VF-402-R in the remote side. After the VF-402-KIT is powered on, wait for at least 15 seconds before connecting the connector to the optical fiber port or else the connector may be damaged or you may get an electric shock.
(5) Connect the 5V DC power adapter to the VF-402-T/VF-402-R and verify that the Power LED lights up. (6) Turn on the power of the analog camera/monitor; the video LED (green) should be lit when all cables are connected. Video...
Page 18
Wall Mount: Mount device on the wall with screws...
Chapter 4. Precautions (1) Insert fiber rightly into the fiber interface; avoid breaking off fiber because of applying too much force. The rolling diameter shall not be too short (not less than 20cm). (2) Fasten the retaining screw after connecting terminal blocks. (3) Do not remove the dust cap before installation.
Chapter 5. Troubleshooting Question Answer or Solution Power supply indicator Check if the power plug is tightly connected and is off. check the fuse wire of chassis. Check if local interference, poor-quality monitor and Abnormal video data. optical output power are normal and in the range of receiving sensitivity.