1. Manuals
  2. Brands
  3. Curtis Manuals
  4. Industrial Monitor
  5. enGage IV
  6. Manual

Curtis enGage IV Manual

Microprocessor based instrument panel
Hide thumbs

Advertisement

Table of Contents

M M A A N N U U A A L L
DIGITAL INSTRUMENTATION

Advertisement

Table of Contents
loading

Summary of Contents for Curtis enGage IV

  • Page 1 M M A A N N U U A A L L DIGITAL INSTRUMENTATION...

  • Page 2: Technical Specifications

    Case H x W 91.8 mm x 137.8 mm 82.6 mm x 128.5 mm Depth 53.5 mm 38.8 mm Weight 400 g max 200 g max Display Dot Matrix LCD (128 X 240 pixels), Backlit page 1 Curtis enGage™ IV Manual...

  • Page 3: Panel Cutout

    (Applicable To Enclosed Units Only): frequency sweep from 10-80-10 Hz (20 g max.) at intervals of 1 minute. IP Ratings Face sealed to IP65. Rear seal Sealed to IP40. (Applicable To Enclosed Units Only): Curtis enGage™ IV Manual page 2...

  • Page 4: Installation

    Section 3.0) LCD Heater V + Dimming Control *Speedometer, Odometer **Tachometer Note: Sender 1, 2, 3 and 4 inputs are limited to 60V max. Voltages beyond that, will damage the instrument. page 3 Curtis enGage™ IV Manual...

  • Page 5: Main Connector

    +7V Out (<10mA – unregulated) 2.2 Mounting Enclosed unit snaps into panel cutout using molded-in fingers. An optional mounting bracket (Curtis P/N 17644307) can be used for additionsal support. Module units are attached via screw holes in the four corners of the PCB.

  • Page 6: User Interface

    2.5 User Interface Curtis enGage™ IV series instruments include 3 front panel buttons for navigating through a menu system and programming the following specific functions: • Time Of Day Clock • Battery Discharge Indicator • Maintenance Intervals • Settable Hour Meters •...
  • Page 7 2.6.3 enGage™ IV Menu System Navigation The diagram below illustrates the navigation through the menu system. enGage IV Menu System FUNCTIONALITY: Press ENTER for 3 Sec mode = NORM mode = MENU to enter MENU mode Press UP/DN to navigate...

  • Page 8: Maintenance Monitor

    Once the desired choice is made, press the select button on the left side of the panel to accept the data. Return to the main menu by utilizing the up / down arrows on panel and selecting "Exit". page 7 Curtis enGage™ IV Manual...

  • Page 9: Operation

    Buttons are utilized for menu navigation as described earlier. 3.1 Auto-range (BDI) Curtis enGage™ IV has an operating voltage range for V+ from 12 to 80 VDC +/- 25%. The source to which pin J1-17 is connected will configure the instrument for the correct Battery Discharge Indicator system voltage.

  • Page 10: Troubleshooting

    Battery may be defective. Resets Without Not connected directly to battery terminals. Charging Battery Empty Too Soon Range Select V+ connected to wrong terminal. Instrument voltage does not match battery voltage. Terminals not connected directly to battery. page 9 Curtis enGage™ IV Manual...

  • Page 11: Maintenance Function

    Sender connected to wrong terminal. Incorrect sender used. Maintenance Function Problem Possible Cause Will Not Reset Procedure as described in Section 2.6 not being followed. 5.0 Maintenance The enGage™ IV 3210 series is not serviceable. Curtis enGage™ IV Manual page 10...
  • Page 12 URTIS NSTRUMENTS, 200 Kisco Avenue Mt. Kisco, New York 10549 USA Tel. 914.666.2971 Fax 914.666.2188 www.curtisinstruments.com Specifications subject to change without notice © 2004 CURTIS INSTRUMENTS, INC. 53040 REV A 2/04...

Table of Contents