TP-Link CPE220 Installation Manual
Outdoor cpe
Hide thumbs
Also See for CPE220:
- Installation manual ,
- User manual (141 pages) ,
- Installation manual (21 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TP-Link CPE220
Summary of Contents for TP-Link CPE220
-
Page 1: Installation Guide
Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520... -
Page 3: Table Of Contents
Contents Overview Hardware Connection Site Consideration Connection and Installation Lightning & ESD Protection Software Configuration Logging into the PharOS Configuration for Typical Applications Antenna Alignment Specifications... -
Page 4: Overview
Overview TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to products including CPE210, CPE220, CPE510 and CPE520. • Package Contents Power Cord Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520... -
Page 5: Panel Layout
• Panel Layout Pharos CPE220 / CPE520: Grounding Shielded Ethernet Shielded Ethernet RESET Terminal Port LAN0 (Passive Port LAN1 PoE in) Pharos CPE210 / CPE510: RESET Grounding Shielded Ethernet Port Terminal LAN (Passive PoE in) - Page 6 Passive PoE Adapter: Remote Reset Power LED Press and hold for 8 seconds to The Power LED is on when the reset the CPE to its factory defaults. passive PoE adapter is working normally.
-
Page 7: Hardware Connection
Hardware Connection 1. Site Consideration • Mounting Height Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting height of the devices. - Page 8 Install the CPE devices with the front facing the intended signal receiving devices. You can orient the devices with the assistance of Google Maps, GPS and some landmarks according to the horizontal beamwidth listed below. Models CPE210 CPE220 CPE510 CPE520 Horizontal Beamwidth 65° 60°...
-
Page 9: Connection And Installation
2. Connection and Installation Please connect and install the device as shown in the figure below. The following introduction takes CPE520 as an example. LAN0 Ethernet cable length up to 60m You should prepare an adequate Connect to a computer, Ethernet cable to connect the CPE router or switch. -
Page 10: Lightning & Esd Protection
3. Lightning & ESD Protection Proper grounding is extremely important for outdoor devices. By using shielded CAT5e (or above) cable with ground wire for the connection and the provided PoE adapter (method 1 ), you can effectively eliminate ESD attacks. If you use the general CAT5e cable for the connection, then it is necessary to connect the grounding terminal of the CPE to earth ground through grounding cable (method 2 ). - Page 11 Sheath Twisted Pair Ground Wire Cable Shield Secondary Cable Shield Shielded RJ45 Connector Shielded CAT5e (or above) Cable with Ground Wire...
-
Page 12: Software Configuration
Software Configuration This chapter introduces the login to the PharOS Web Interface and the software configurations. 1. Logging into the PharOS Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.X (X ranges between 2 and 253, e.g. 192.168.0.10) to your computer. - Page 13 Enter admin for both User Name and Password. Read and agree the terms of use, then click Login. Change the default User Name and Password to protect your CPE. Let’s start configuring the CPE. For subsequent logins, use the new username and password.
-
Page 14: Configuration For Typical Applications
2. Configuration for Typical Applications The typical topology is as follows. A wireless bridge is built between two locations that are far from each other. Follow the instructions below to configure the Access Point and the Client. IP camera Computer Access Point Client LAN: 192.168.0.254... - Page 15 LAN Settings: Change the IP Address to 192.168.0.X (X ranges between 2 and 253), the same subnet with the access point, and click Next. Wireless Client Settings: a. Click Survey and select the SSID of the Access Point in the AP list, then click Connect.
-
Page 16: Antenna Alignment
Antenna Alignment In order to get the best performance, you can precisely align the direction of the CPE with the assistance of Wireless Signal Quality on STATUS page of the PharOS Web Interface. Adjust the direction of the CPE until the device reaches the highest SNR. -
Page 17: Specifications
Specifications HARDWARE FEATURES CPE520/CPE220: 275.83*79*60.3mm Dimensions CPE510/CPE210: 224.34*79*60.3mm CPE520/CPE220 CPE510/CPE210 LAN0: 10/100Mbps LAN: 10/100Mbps Ethernet Port(PoE IN) Ethernet Port(PoE IN) LAN1: 10/100Mbps Interface Ethernet Port GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default... -
Page 18: Faq
Q1. How to restore the CPE to its factory default settings? With the CPE powered on, press and hold the RESET button on the CPE or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. Method 1: The following picture takes CPE520 as an example. - Page 19 Q2. How to calculate the minimum mounting height of the devices? In order to maximize the received signal strength of the devices, installers need to minimize the effect of the out-of-phase signals, which is caused by obstacles in the path between the transmitter and the receiver.
- Page 20 Q3. What is Pharos MAXtream? Pharos MAXtream is a proprietary protocol developed on the basis of Time Division Multiple Access (TDMA) by TP-Link. The MAXtream technology has the following advantages: • Eliminates hidden node collisions & improves channel efficiency. • Lower latency, higher throughput, larger network capacity &...
- Page 21 average curve indicates less radio noise. Here, we use the figure below as an example. The select box of Frequency Range at the top-left corner is only available for CPE510 and CPE520. Select the desired range and then click Start. When choosing channel/frequency, you should avoid the spectrum with large radio noise.
- Page 22 FCC STATEMENT (For CPE220/CPE510/CPE520) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
-
Page 23: Canadian Compliance Statement
The device complies with RF specifications when the device used at 20 cm from your body. (For CPE220/CPE510/CPE520) This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. -
Page 24: Safety Information
(c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Industry Canada Statement (For CPE220/CPE510/CPE520) CAN ICES-3 (A)/NMB-3(A) Industry Canada Statement (For CPE210) - Page 25 時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業 之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機 設備之干擾。 安全諮詢及注意事項 • 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 • 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 • 注意防潮，請勿將水或其他液體潑灑到本產品上。 • 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 • 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 • 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 (For CPE220/CPE510/CPE520) 此為甲類資訊技術設備，于居住環境中使用時，可能會 造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
- Page 26 User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. (For CPE220/CPE510/CPE520) この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を 引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求され VCCI-A ることがあります。 ...
- Page 28 GNU General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (http://www.tp-link.com/en/support/gpl/). The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors.