Related Manuals for ADEMCO 6220
Summary of Contents for ADEMCO 6220
- Page 1 ADEMCO Model 6220 Printer Series ADEMCO 165 Eileen Way, Syosset, NY 11791 Ph: 516-921-6704 User's Manual Fax: 516-677-9559 http://www.ademco.com A Pitway Company...
- Page 2 ADEMCO reserves the right to change ADEMCO reserves the right to change ADEMCO reserves the right to change ADEMCO reserves the right to change ADEMCO reserves the right to change specifications at any time.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Introduction .................... 1 Installation....................1 Installing the Paper ................1 To Remove the Paper Roll ..............4 Operation ....................5 Connecting and Powering up Your Printer .......... 5 Maintenance ................... 6 Changing the Printer Ribbon ............... 6 Inserting a Ribbon with Paper in the Printer ........ - Page 4 Specifications Custom Menu Custom Menu Custom Menu Custom Menu Custom Menu Configuration Menu Configuration Menu Configuration Menu Configuration Menu Configuration Menu Interface-Serial Available BAUD rates: 300, 600, 1200, 2400, T/D Format 1 - None Baud 1 - 300 2 - MM/DD/YY_hh:mm_?M 2 - 600 4800, 9600, 19200 3 3 3 3 3 - - - - - MM/DD/YY hh:mm ?M DOW...
- Page 5 Note the last two codes of the usual ASCII U/L approved Agencies character sets are not supported. Instead, if CHR$(126), which corresponds to hexadecimal External Dimensions 4"W x 4.5"L x 2"H 7E, is received by the 1220 printer, it will print the character defined in its RAM (Random Operating Temp 5°C to 40°C, 41°F to 104°F...
-
Page 6: Introduction
Cancel Reverse Field verse field mode that is selected using control Control Code 24 code 25. The ADEMCO Model 6220 dot matrix printer series consists of these models and electrical Reverse Field Send this control code to turn ON the reverse interfaces: field printing mode. - Page 7 The DATA statement in your program will read: 2. Press the rocker switch to the left. The light DATA 28, 34, 65, 65, 54, 34 will go off. The next step is to tell the printer your newly 3. Unroll several inches of the paper. designed character.
- Page 8 7. When an inch of paper has emerged from 1. Use quad ruled paper to design your the top of the printer, release the Paper Feed character. button. 2. Number 8 consecutive rows like this: 8. Now pull the paper through the printer, until several inches are exposed.
-
Page 9: To Remove The Paper Roll
Example 1: 12. Put the paper spindle into the paper roll as shown below, and place the roll with the spindle onto the snaps near the back of the printer. Turn the paper roll to take up any slack in the paper feeding to the printer. Make sure the roll of paper turns freely. -
Page 10: Operation
Operation be convenient. If such a large sheet of paper is not available, you could divide your pattern in Connecting and 1. Attach the appropriate cable between the half and work with 72 grid boxes across. Divide Powering Up printer and your computer. The connector on up your grid paper by drawing a heavy line down Your Printer the printer side is “keyed”... -
Page 11: Maintenance
it is desirable to eliminate the two blank lines Maintenance so the graphic characters connect together. Sending a CHR$(17), which is control code 17, When printing becomes faint or difficult to see, anywhere on a line of data will stop the printer replace the ribbon in your printer with an Epson from putting space between that line and the ERC-09 cartridge ribbon. - Page 12 3. When the printer cover is tilted up, lift it This control code tells the printer to switch to completely off. double width character printing. The control code should be sent as the first character on a 4. Push down on the right side of ribbon car- line.
-
Page 13: Printer Test And Setup
Upon receipt of this code, the printer erases Back Space from its buffer the previously received charac- Code 8 ter. This is useful in correcting typing errors for programs that send data both to a video screen and the hard copy printer. Remember that if you type more characters than the printer can print on a line, the printer will automatically start printing. - Page 14 According to the American Standard Code of T&D will be printed in the list Control Codes Information Interchange (ASCII), there are 32 to the right if the Time and control codes in addition to the codes for the Date option is installed. printable characters.
-
Page 15: Configure
If you wait less than three or more than five seconds R R R R R eady eady eady eady... . is printed and you will have eady . . . to try steps 1 and 2 again to access the setup menu. - Page 16 Equivalent to DB-25S (Canon) On the cable: 25-pin plug Equivalent to DB-25P (Canon) Shell: Equivalent to DB-C2-J9 (Canon) L L L L L O O O O O AD DEF AD DEF AD DEF AD DEFA A A A A UL AD DEF ULTS TS gives you the opportunity to...
- Page 17 D D D D D A A A A A T T T T T A BITS A BITS A BITS A BITS A BITS is the next parameter. Choose the Data Bits PIN NO PIN NO PIN NO..SIGNAL SIGNAL DIRECTION...
-
Page 18: Reset Seq
Model 6220S This section shows the cable differences in the out of the configuration menu and the setup models of the 6220 series printer and the con- RS-232 Serial Version menu and is ready to print. trol codes and communication protocols. - Page 19 The cursor now appears over the 2nd position. Press NEXT NEXT NEXT NEXT (left side) to increment this num- NEXT ber if needed and OK OK if it is right. Continue this This manual assumes the time sequence of accepting or changing the year, and date option are installed month, day, and DOW (Day Of Week).
- Page 20 A A A A A UT UTO SEQUENCE NUMBER O SEQUENCE NUMBER O SEQUENCE NUMBER O SEQUENCE NUMBER O SEQUENCE NUMBER is the next YES - Allows you to use hexidecimal Auto Seq# The choice to use the parameter. Choices are: numbers above 80 (true only for 8 data bits.) extended character set is available only when 8 data...